CommScope ION-M17EHP/19P Manuel utilisateur

ION®-M17EHP/19P

Optical Remote Unit

(M-Cabinet)

Manual

MF0150A1A

Page 2 MF0150A1A.doc Manual for ION-M17EHP/19P

DISCLAIMER:

This document has been developed by CommScope, and is intended for the use of its

customers and customer support personnel. The information in this document is subject to

change without notice. While every effort has been made to eliminate errors, CommScope

disclaims liability for any difficulties arising from the interpretation of the information

contained herein. The information contained herein does not claim to cover all details or

variations in equipment, nor to provide for every possible incident to be met in connection

with installation, operation, or maintenance. This document describes the performance of the

product under the defined operational conditions and does not cover the performance under

adverse or disturbed conditions. Should further information be desired, or should particular

problems arise which are not covered sufficiently for the purchaser’s purposes, contact

CommScope.

CommScope reserves the right to change all hardware and software characteristics without

notice.

This document is protected by copyright. No part of this document may be reproduced,

stored in a retrieval system, or transmitted, in any form or by any means, electronic,

mechanical photocopying, recording, or otherwise without the prior written permission of

CommScope.

TRADEMARKS

All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of

CommScope. Names of products mentioned herein are used for identification purposes only

and may be trademarks and / or registered trademarks of their respective companies.

Andrew Wireless Systems GmbH, 09-December-2015

Table of Contents

MF0150A1A.doc Manual for ION-M17EHP/19P Page 3

TABLE OF CONTENTS

1.GENERAL 5

1.1.USED ABBREVIATIONS 5

1.2.HEALTH AND SAFETY 6

1.3.PROPERTY DAMAGE WARNINGS 6

1.4.COMPLIANCE 7

1.5.ABOUT COMMSCOPE 9

1.6.INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT 10

2.INTRODUCTION 12

2.1.PURPOSE 12

2.2.ION-M17EHP/19P 12

3.FUNCTIONAL DESCRIPTION 13

3.1.ACCESSORY EQUIPMENT 13

3.1.1.Fan-Protection Kit 13

3.1.2.Accessories 13

4.COMMISSIONING 14

4.1.MECHANICAL INSTALLATION 14

4.1.1.Health and Safety for Mechanical Installation 14

4.1.2.Property Damage Warnings for Mechanical Installation 14

4.1.3.Wall-Mounting Procedure 16

4.1.4.Pole Mounting 17

4.1.5.Mounting of Fan Protection 19

4.2.ELECTRICAL INSTALLATION 20

4.2.1.Health and Safety for Electrical Installation 20

4.2.2.Property Damage Warnings for Electrical Installation 20

4.2.3.Connections 21

4.2.4.Grounding (Earthing) 21

4.2.5.Connection of the Antenna Cables 22

4.2.6.Cleaning Procedure for RF Cable Connectors 23

4.2.7.Antenna Cable Connector Assembly 26

4.2.8.Optical-Fiber-Cable Connection - Rules 27

4.2.9.Protective Plug 29

4.2.10.Protective-Tube Kit 31

4.2.11.External-Alarm Inputs and Outputs 33

4.2.12.Power Connection 36

4.2.13.Commisioning Flowchart 37

5.ALARMS AND TROUBLESHOOTING 39

Figures and Tables

Page 4 MF0150A1A.doc Manual for ION-M17EHP/19P

6.MAINTENANCE 40

6.1.GENERAL 40

6.2.REPLACING THE FAN UNIT 41

6.3.CLEANING THE HEAT SINK 42

7.APPENDIX 43

7.1.ILLUSTRATIONS 43

7.2.SPECIFICATIONS 44

7.2.1.Electrical Specifications 44

7.2.2.Environmental and Safety Specifications 44

7.2.3.Mechanical Specifications 44

7.3.SPARE PARTS 45

8.INDEX 46

FIGURES AND TABLES

figure 4-1 Wall mounting, (metric dimensions)........................................................... 16

figure 4-2 Pole-mounting kit........................................................................................ 17

figure 4-3 Pole mounting (metric dimensions)............................................................ 18

figure 4-4 Mounting procedure for fan protection, (metric dimensions) ..................... 19

figure 4-5 Connector flange of ION-M17EHP/19P ..................................................... 21

figure 4-6 Grounding bolt (left) and schematic view (right) ........................................ 21

figure 4-7 Torque wrench for tightening ..................................................................... 22

figure 4-8 Protective-plug assembly ........................................................................... 29

figure 4-9 Tube-kit installation .................................................................................... 32

figure 4-10 Flange connector, 5 poles........................................................................ 34

figure 4-11 Alarm inputs (optocoupler) ....................................................................... 34

figure 4-12 Alarm outputs (optocoupler)..................................................................... 35

figure 4-13 Flange connector, 7 poles........................................................................ 35

figure 4-14 Power supply cables (AC)........................................................................ 36

figure 4-15 Power supply cable (DC) ......................................................................... 36

figure 7-1 Cabinet drawing ......................................................................................... 43

table 1-1 List of international contact addresses........................................................ 11

table 4-1 Specified torques......................................................................................... 15

table 5-1 Status LED alarms....................................................................................... 39

1. General

MF0150A1A.doc Manual for ION-M17EHP/19P Page 5

1.General

1.1.Used Abbreviations

3GPP 3rd Generation Partnership Project

AC/DC Alternating current / Direct Current

AIMOS Andrew Integrated Management and Operating System

ALC Automatic Level Control

BITE Built-In Test Equipment

BTS Base Transceiver Station

CE "Conformité Européenne" ("European Conformity")

CD Compact Disk

CFR Code of Federal Regulations

DL Downlink

DoC Declaration of Conformity

EDGE Enhanced Data Rates for GSM Evolution

EN European Norm

ESD Electrostatic Discharge

ETS European Telecommunication Standard

GSM Global System for Mobile Communication

GND Ground

GUI Graphical User Interface

ICP3 Intercept Point 3rd order

ID No Identification Number

ION Intelligent Optical Network

IP Ingress Protection

ISO International Organization for Standardization

LED Light Emitting Diode

LMT Local Maintenance Terminal

LTE Long Term Evolution

MIMO Multiple Input Multiple Output

MS Mobile Station

MU Main Unit

NF Noise Figure

OTRx Optical Transceiver = SRMU (Subrack Master Unit)

PG Packing Gland

PIM Passive Intermodulation

R&TTE Radio & Telecommunications Terminal Equipment

RF Radio Frequency

RU Remote Unit

RX Receiver

SNMP Simple Network Management Protocol

TX Transmitter

UL Uplink

UMTS Universal Mobile Telecommunication System

UPS Uninterruptible Power Supply

WCDMA Wideband Code Division Multiple Access

WDM Wavelength Division Multiplex

1. General

Page 6 MF0150A1A.doc Manual for ION-M17EHP/19P

1.2.Health and Safety

1. Danger: Electrical hazard. Danger of death or fatal injury from electrical

current. Obey all general and regional installation and safety regulations

relating to work on high voltage installations, as well as regulations

covering correct use of tools and personal protective equipment.

2. Danger: Electrical hazard. Danger of death or fatal injury from electrical

current inside the unit in operation. Before opening the unit, disconnect

mains power.

3. Caution: Laser radiation. Risk of eye injury in operation. Do not stare into the

beam; do not view it directly or with optical instruments.

4. Caution: High frequency radiation in operation. Risk of health hazards associated

with radiation from the unit’s inner conductor of the antenna port(s). Disconnect

mains before connecting or replacing antenna cables.

5. Caution: High frequency radiation in operation. Risk of health hazards associated

with radiation from the antenna(s) connected to the unit. Implement prevention

measures to avoid the possibility of close proximity to the antenna(s) while in

operation.

1.3. Property Damage Warnings

1. Attention: Due to power dissipation, the remote unit may reach a very high

temperature. Do not operate this equipment on or close to flammable materials.

Use caution when servicing the unit.

2. Attention: Only authorized and trained personnel are allowed to open the unit

and get access to the inside.

3. Notice: Although the Remote Unit is internally protected against overvoltage, it is

strongly recommended to ground (earth) the antenna cables close to the antenna

connectors of the Remote Unit for protection against atmospheric discharge. In

areas with strong lightning, it is strongly recommended to install additional

lightning protection.

4. Notice: ESD precautions must be observed. Before commencing maintenance

work, use the available grounding (earthing) system to connect ESD protection

measures.

5. Notice: Only suitably qualified personnel are allowed to work on this unit and only

after becoming familiar with all safety notices, installation, operation and

maintenance procedures contained in this manual.

6. Notice: Keep operating instructions within easy reach and make them available

to all users.

1. General

MF0150A1A.doc Manual for ION-M17EHP/19P Page 7

7. Notice: Read and obey all the warning labels attached to the unit. Make sure that

all warning labels are kept in a legible condition. Replace any missing or

damaged labels.

8. Notice: Only license holders for the respective frequency range are allowed to

operate this unit.

9. Notice: Make sure the repeater settings are correct for the intended use (refer to

the manufacturer product information) and regulatory requirements are met. Do

not carry out any modifications or fit any spare parts, which are not sold or

recommended by the manufacturer.

1.4. Compliance

1. Notice: For installations, which have to comply with FCC RF exposure

requirements, the antenna selection and installation must be completed in a way

to ensure compliance with those FCC requirements. Depending on the RF

frequency, rated output power, antenna gain, and the loss between the repeater

and antenna, the minimum distance D to be maintained between the antenna

location and human beings is calculated according to this formula:

]/[

][

][ 2

4cmmW

cm PD

D





where

P (mW) is the radiated power at the antenna, i.e. the max. rated repeater

output power in addition to the antenna gain minus the loss between the

repeater and the antenna.

PD (mW/cm²) is the allowed Power Density limit acc. to 47 CFR 1.1310 (B)

for general population / uncontrolled exposures which is

oF (MHz) / 1500 for frequencies from 300MHz to 1500MHz

o1 for frequencies from 1500MHz to 100,000MHz

RF exposure compliance may need to be addressed at the time of licensing, as

required by the responsible FCC Bureau(s), including antenna co-location

requirements of 1.1307(b)(3).

2. Notice: For installations which have to comply with European EN50385 exposure

compliance requirements, the following Power Density limits/guidelines (mW/cm²)

according to ICNIRP are valid:

o0.2 for frequencies from 10 MHz to 400 MHz

oF (MHz) / 2000 for frequencies from 400 MHz to 2 GHz

o1 for frequencies from 2 GHz to 300 GHz

1. General

Page 8 MF0150A1A.doc Manual for ION-M17EHP/19P

3. Notice: Installation of this equipment is in full responsibility of the installer, who

has also the responsibility, that cables and couplers are calculated into the

maximum gain of the antennas, so that this value, which is filed in the FCC Grant

and can be requested from the FCC data base, is not exceeded. The industrial

boosters are shipped only as a naked booster without any installation devices or

antennas as it needs for professional installation.

4. Notice: The unit complies with Overvoltage Category II. It also complies with the

surge requirement according to EN 61000-4-5 (fine protection); however,

installation of an additional medium (via local supply connection) and/or coarse

protection (external surge protection) is recommended depending on the

individual application in order to avoid damage caused by overcurrent.

For Canada and US, components used to reduce the Overvoltage Category shall

comply with the requirements of IEC 61643-series. As an alternative, components

used to reduce the Overvoltage Category may comply with ANSI/IEEE C62.11,

CSA Certification Notice No. 516, CSA C22.2 No. 1, or UL 1449. Suitability of the

component for the application shall be determined for the intended installation.

5. Notice: Corresponding local particularities and regulations must be observed. For

national deviations, please refer to the respective documents included in the

manual CD that is delivered with the unit.

6. Note: This unit complies with European standard EN60950.

Equipment Symbols Used / Compliance

Please observe the meanings of the following symbols used in our equipment and

the compliance warnings:

Symbol Compliance Meaning / Warning

--- FCC

For industrial (Part 20) signal booster:

WARNING: This is NOT a CONSUMER device. It is

designed for installation by FCC LICENSEES and

QUALIFIED INSTALLERS. You MUST have an FCC

LICENSE or express consent of an FCC Licensee to

operate this device. Unauthorized use may result in

significant forfeiture penalties, including penalties in

excess of $100,000 for each continuing violation.

Alert sign to R&TTE

To be sold exclusively to mobile operators or

authorized installers – no harmonized frequency

bands, operation requires license. Intended use: EU

and EFTA countries.

Indicates conformity with the R&TTE directive

1999/5/EC certified by the notified body no. 0700.

1. General

MF0150A1A.doc Manual for ION-M17EHP/19P Page 9

1.5. About CommScope

CommScope is the foremost supplier of one-stop, end-to-end radio frequency (RF)

solutions. Part of the CommScope portfolio are complete solutions for wireless

infrastructure from top-of-the-tower base station antennas to cable systems and

cabinets, RF site solutions, signal distribution, and network optimization. For patents

see www.cs-pat.com.

CommScope has global engineering and manufacturing facilities. In addition, it

maintains field engineering offices throughout the world.

Andrew Wireless Systems GmbH based in Buchdorf/Germany, which is part of

CommScope, is a leading manufacturer of coverage equipment for mobile radio

networks, specializing in high performance, RF and optical repeaters. Our optical

distributed networks and RF repeater systems provide coverage and capacity

solution for wireless networks in both indoor installations and outdoor environments,

e.g. tunnels, subways, in-trains, airport buildings, stadiums, skyscrapers, shopping

malls, hotels and conference rooms.

Andrew Wireless Systems GmbH operates a quality management system in

compliance with the requirements of ISO 9001 and TL 9000. All equipment is

manufactured using highly reliable material. To maintain highest quality of the

products, comprehensive quality monitoring is conducted at all fabrication stages.

Finished products leave the factory only after a thorough final acceptance test,

accompanied by a test certificate guaranteeing optimal operation.

This product meets the requirements of the R&TTE directive and the Declaration of

Conformity (DoC) itself. A current version of the CE DoC is included in this manual

CD delivered *. Any updated version of the DoC is available upon request from the

local sales offices or directly from CommScope via the local Customer Support at

one of the addresses listed in the following chapter.

According to the DoC, our "CE"-marked equipment can be used in all member

states of the European Union.

Note: Exceptions of and national deviations from this intended use may be

possible. To observe corresponding local particularities and

regulations, please refer to the respective documents (also in

national language) which are included in the manual CD delivered.

* In case the Declaration of Conformity (DoC) for the product was not included in the manual CD

delivered, it is available upon request from the local sales offices or directly from CommScope at

one of the addresses listed in the following chapter.

To make the most of this product, we recommend you carefully read the instructions

in this manual and commission the system only according to these instructions.

For technical assistance and support, please also contact the local office or

CommScope directly at one of the addresses listed in the following chapter.

1. General

Page 10 MF0150A1A.doc Manual for ION-M17EHP/19P

1.6.International Contact Addresses for Customer Support

Canada

United States

CommScope Canada

ndrew LLC, A CommScope Company

Mail 505 Consumers Road, Suite 803

Toronto M2J 4V8, Canada Mail 620 North Greenfield Parkway

Garner, NC 27529, U.S.A.

Phone +1-905-878-3457 (Office)

+1-416-721-5058

(

Cell

)

Phone +1-888-297-6433

Fax +1-905-878-3297 Fax +1-919-329-8950

E-mail [email protected] E-mail [email protected]

Caribbean & South American Region Caribbean & Central American Region

CommScope Cabos do Brasil Ltda. CommScope Mexico S.A. de C.V.

Mail

CALA Tech Support for Distributed

Coverage & Capacity Solutions (DCCS)

products:

Rua Guaporanga, 49

Praça Seca – Rio de Janeiro – RJ

ZIP: 21320-180, Brazil

Mail

CALA Tech Support for Distributed

Coverage & Capacity Solutions

(DCCS) products:

Av. Insurgentes Sur 688, Piso 6

Col. Del Valle, CP: 03100

Mexico City, Mexico

Phone +1-815-546-7154 (Cell)

+55-15-9104-7722 (Office) Phone +52-55-1346-1900 (Office)

Fax + 55-15-2102-4001 Fax +52-55-1346-1901

E-mail [email protected] E-mail [email protected]

China, India and Rest of Asia

Australia & New Zealand

Andrew International Corporation

ndrew Corporation (Australia) Pty Ltd.

Mail

Room 915, 9/F

Chevalier Commercial Centre

8 Wang Hoi Rd

Kowloon Bay, Hong Kong

Mail

Unit 1

153 Barry Road

Campbellfield

VIC 3061, Australia

Phone +852-3106-6100 Phone +613-9300-7969

Fax +852-2751-7800 Fax +613-9357-9110

E-mail wisupport.China@commscope.com E-mail [email protected]

Middle East & North Africa

Africa

Middle

East

South Africa

CommScope Solutions International Inc.

(Branch)

ndrew Wireless Solutions Africa

(PTY) LTD

Mail

PO Box 48 78 22

Unit 3206, Floor 32,

Jumeirah Business Center 5,

Jumeirah Lakes Towers,

Dubai, United Arab Emirates

Mail

11 Commerce Crescent West

Eastgate, Sandton

PO Box 786117

Sandton 2146

South Africa

Phone +971 4 390 09 80 Phone + 27 11-719-6000

Fax +971 4 390 86 23 Fax + 27 11-444-5393

E-mail [email protected] E-mail [email protected]

Table des matières

Autres manuels CommScope Matériel réseau

CommScope

CommScope NOVUX SEC 100 Manuel utilisateur

CommScope

CommScope RUCKUS SmartZone 300 Manuel utilisateur

CommScope

CommScope ION-U EU H 23/23 Manuel utilisateur

CommScope

CommScope ST-BSP60 Manuel utilisateur

CommScope

CommScope WCS-2 Manuel utilisateur

CommScope

CommScope UNJ10G Manuel utilisateur

CommScope

CommScope LSX Manuel utilisateur

CommScope

CommScope NETCONNECT 1479542-1 Manuel utilisateur

CommScope

CommScope TC-96370-IP Manuel utilisateur

CommScope

CommScope CPP-UDDM-SL-1U-24 Manuel utilisateur

CommScope

CommScope EHD Manuel utilisateur

CommScope

CommScope SYSTIMAX EHD Manuel utilisateur

CommScope

CommScope ONECELL RP5200 Manuel

CommScope

CommScope FPX Series Manuel utilisateur

CommScope

CommScope OneCell RP5000 Series Mode d’emploi

CommScope

CommScope NG4access ODF Platform Value-Added Module Manuel utilisateur

CommScope

CommScope Mini-OTE 300 Manuel utilisateur

CommScope

CommScope FOSC-OC-6 Manuel utilisateur

CommScope

CommScope ION-M23 SDARS Manuel utilisateur

CommScope

CommScope FPX Series Manuel utilisateur

CommScope

CommScope CPPR-QF-F-1U-E Manuel utilisateur

CommScope

CommScope SCIL-B Manuel utilisateur

CommScope

CommScope NG4access ODF Platform Value-Added Module Manuel utilisateur

CommScope

CommScope M3200 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur