CommScope SCIL-B Manuel utilisateur

1.1 Product Description

Cable diameter range: 0-5mm, including fig.8 cable.

1.2 Kit Content

* Standard kit is listed below, alternative kits and

accessories are available.

1. 6-out multiport kit

2. Blank plugs

3. Tie wraps (8pcs)

4. Cleaning tissue

5. Foamstrip

6. Saddle seat and screw

7. Installation instruction

2 Cable Installation – Fig.8 Cable

2.1 Clean the cable for 1.5m from the cable jacket

end.

2.2 Install the cables according to the sequence

shown.

2.3 Remove the blank plugs from ports where cable

will be installed.

2.4Pull the cable through the gel block up to

1300mm.

SCIL-B 6-OUT MULTIPORT KIT

I N S T A L L A T I O NI N S T R U C T I O N

使使使使

用用用用

说说说说

明明明明

书书书书

1st 1st

2nd 2nd

3rd

TC-1362-3-IP

Rev A, Aug 2017

www.commscope.com

EM1354-001

Rev. A

2.5 Cable fixation position is shown below.

2.6 Wrap the cable with the foam strip at a proper

position, and secure the cable at the foam part with

tie wraps.

2.7 Install the saddle seat where the multiport kit will

be installed.

2.8 Install the tie wrap onto the saddle seat.

2.9 Insert the multiport kit into the slot shown.

2.10 Secure the multiport kit with tie wrap. Keep the

multiport kit level. Do not tilt the trigger part.

1 2 3

2.11 Remove the cable sheath at proper length, and

wrap the cable with the foam strip at the cable jacket

end. Secure the cable at the tray entrance with tie

wraps.

2.12 After closing all closure latches, screw the

multiport trigger clockwise until it stops.

3 Cable Installation – Round Cable

3.1 Clean the cable sheath with the cleaning tissue.

3.2 -3.6 Repeat 2.2 -2.6

3.7 Remove the cable jacket as shown.

3.8-3.11Repeat 2.7-2.10

3.12 Remove the loose tube up to 150mm from the

cable sheath end.

3.13 Clean the fiber bundle. Slide the transportation

tubes over the fibers up to 50mm from the cable

sheath end.

3.14 Route the transportation tubes to the tray

entrance. Secure the transportation tubes with tie

wraps.

3.15 After closing all closure latches, screw the

multiport trigger clockwise until it stops.

4. Re-entry & Additional Cable Installation

4.1 Unscrew the multiport trigger anti-clockwise first

and then open all latches to open the closure.

4.2 Repeat step 2.3.

4.3 After removing the multiport kit, store the

multiport kit at the cable port.

4.4 Repeat the steps in item 2 or 3 to install the new

cables.

CommScope and all trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc.

This document is for planning purposes only and is not intended to modify or supplement any speciﬁcations or warranties relating to

CommScope products or services.

This product is covered by one ore more U.S. patents or their foreign equivalents. For patents, see:

www.commscope.com/ProductPatent/ProductPatent.aspx.

To ﬁnd out more about CommScope® products, visit us on the

web at www.commscope.com

For technical assistance, customer service, or to report any

missing/damaged parts, visit us at:

http://www.commscope.com/SupportCenter

Autres manuels pour SCIL-B

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels CommScope Matériel réseau

CommScope

CommScope SD-4U-SPLICE PANEL Manuel utilisateur

CommScope

CommScope FDC-W8-FAT Manuel utilisateur

CommScope

CommScope Constellation CPT-PP-48C Manuel utilisateur

CommScope

CommScope Mini-OTE 300 Manuel utilisateur

CommScope

CommScope UNJ10G Manuel utilisateur

CommScope

CommScope RUCKUS SmartZone 100 Manuel utilisateur

CommScope

CommScope NG4access ODF Platform Value-Added Module Manuel utilisateur

CommScope

CommScope ION-M23 SDARS Manuel utilisateur

CommScope

CommScope SYSTIMAX EHD Manuel utilisateur

CommScope

CommScope NOVUX SEC 100 Manuel utilisateur

CommScope

CommScope LSX Manuel utilisateur

CommScope

CommScope RUCKUS SmartZone 300 Manuel utilisateur

CommScope

CommScope WCS-2 Manuel utilisateur

CommScope

CommScope NG4access ODF Platform Value-Added Module Manuel utilisateur

CommScope

CommScope ONECELL RP5200 Manuel

CommScope

CommScope SYSTIMAX AirSPEED AP542 Manuel utilisateur

CommScope

CommScope ION-M17EHP/19P Manuel utilisateur

CommScope

CommScope CPPR-QF-F-1U-E Manuel utilisateur

CommScope

CommScope AMP NETCONNECT MRJ21 Manuel utilisateur

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Manuel utilisateur

CommScope

CommScope FPX Series Manuel utilisateur

CommScope

CommScope ION-M7P Manuel utilisateur

CommScope

CommScope FPX Series Manuel utilisateur

CommScope

CommScope ION-M7P Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur