CommScope FDC-W8-FAT Manuel utilisateur

Fiber Drop Closure for Fiber Access Terminal

Contents 1 General

2 Sizing and product kit

information

3 Installation conditions

precautions

4 Closure preparation

5 Cable installation

6 Fiber preparation

7 Splicing and fiber storage

8 Pole mount installation

9 Wall mount installation

10 Re-entry and drop cable installation

1 General

1.1 Installation Instruction description

The installation instruction describes the necessary steps to install the FDC-W8. The installation

instruction illustrates the use on loose tube cables. If other cable types are used, please contact

the local agent for relevant accessories and instructions.

1.2 Product description

The FDC-W8-FAT is a butt type gel sealed fiber optic splicing and patching closures designed for

fiber access point applications in the telecom outside plant network. FDC-W8 FAT has 4 main

cable ports and 8 drop cable ports. Loop storage of 6m loose tubes allows 2 main cables loop

through at the same time. The closure accommodates up to 24 fusion splices (or 8 mechanical

splices), two PLC splitters and 8 SC adapters. Sealing is achieved visa built-in gel technology,

resulting in extremely convenient re-entry and re-sealing.

2 Sizing and product kit information

2.1 Dimensions

Main Cable diameter range 8-14 mm

Drop Cable diameter: 3mm round cable or 2 X3mm fig.8 cable

Closure outer dimensions 266 x 237 x 76.5 mm

FDC-

8-FAT

INSTALLATION INSTRUCTIO N

TC-2164-IP

Rev. A, May 2018

www.commScope.com

CZ2416-000 Rev B

2.2 Kit content

* Below listed is a standard kit, alternative kits and accessories

are available.

1. Cover and base with latch

Tray

kits 1

3.Splitter 1

4. Cable bracket and screws 4 sets

Adaptors 8

pcs

6. Transportation

tubs 4

pcs

7. Twist wrap and screw2 sets

8. Big head screw 4

pcs

9.Smouv

10. Ring tree 2

pcs

11. Dummy rod (small) 2 pcs

12. Dummy rod (8mm) &snap block 4 pcs

13. White tie wraps 12

pcs

14. Black tie wraps4

15. Clean tissue 1

16. Installation instruction

3 Installation conditions precautions

3.1 The closures should be installed at temperature

between -5°C and 45°C.

3.2 Follow the installation instruction steps to ensure the

performance of the closure.

3.3 It is necessary to take precautions and keep the

working space clean to protect the closure sealing

materials and splices.

4 Closures preparation

4.1 Open the closures by unscrew the all screws on the

closure cover, as shown in left below. Then

unlatched two sides, as shown, in right below.

4.2 Open the cover. Then open the tray by press-in the

tray latch, as shown.

4.3 Unscrew the upper clamps where you will install the

cable.

Note: Prefer to use manual screwdriver or electric

screwdriver in low speed.

4.4 Take out upper clamp and the dummy rods.

4.5 Separate the dummy rod and the blocking ring, as

shown

4.6 According to the cable range choose the appropriate

side of the cable clamp and remove the white sleeve

layer installed on the lower clamp if necessary (refer

to Table 1).

Cable

range

(mm)

Cable

clamp

White snap

block

Blocking

ring

8-9.3 Small Yes Yes

9.3-12 Small Remove Remove

12-14 Large Remove Remove

Table 1, Cable clamp selection

Clamp type

White snap block

5 Cable Installation

5.1 Make a window cut of 1500mm and cut the strength

member up to 50mm from the cable jacket end.

Note: If the cable has jacket covered on strength

member, Please remove the jacket before

installation.

5.2 Clean the cable sheath, where it contacts gel, with

cleaning tissue provided.

50mm

1500mm

Large

Small

5.3 Fix the strength member underneath the metal screw

as shown in Step 5.4. Tighten the screw to secure the

strength member. Cut the excess off.

5.4 Fit the cable onto the designated cable port and

make sure the blocking ring is in the slot, as shown.

5.5 Screw tight the upper clamps

Note: After slightly tighten the first screw, firmly

tighten the second screw. Then, firmly tighten the first

screw.

Note: leave 10mm from the clamp end to the tip end

for each cable, as shown below.

5.6 Secure cables with tie wraps, as shown. Cut the

excess off.

6 Fiber preparation

6.1 Loop the pass-through cable slack, as shown.

Note:

Use Port 1, Port 4 for one loop cable

Use Port 2, Port 3 for second loop cable

10mm

1 2 3 4

6.2 Secure the pass-through cable slack, as shown.

6.3 Strip the input fiber cable

6.4 Degrease the fiber bundle and slide the

transportation tubes over the fibers with overlap

50mm

6.5 Route the transparent tubes to the tray entrance, as

shown

6.6 Secure the transportation tube at the tray entrance

with two tie wraps.

Note: Maximum two transportation tubes per tray

entrance.

7 Splicing and fiber storage

7.1 Position the closure close to the splicing machine in a

convenient location and secure the closure

7.2 Slide the heat-shrinkable splice protection over one

fiber and fuse fibers according to local

recommendations and procedures. After the fusion

splice is made, install the heat-shrinkable splice

protection (e.g. SMOUV) with an appropriate heating

source. Allow the splice protection to cool down to

ambient temperature.

# 1

#4 # 1

100 mm

50 mm

7.3 After each splice is made, the splice should be stored

in the splice holder in the appropriate position, as

shown. Do not deform the splice protector during

insertion

7.4 Put on the tray lid.

7.5 Put back the drop cable tray..

7.6 Close the closure

8 Pole mount installation

8.1 Insert the two pole strips onto the closure, as shown

8.2 Screw tight on the pole

9 Wall mount installation

9.1 Holes dimensions:

219 mm

194mm

10 Re-entry and drop cable installation

10.1 Unscrew the center screw and unlatch the top

cover, as shown.

10.2 Fully open the cover, as shown.

10.3 For easy FIC insertion, tilt the adapter, as shown.

10.4 Complete FIC connector assembly.

10.5 Remove the dust cap and insert the FIC.

10.6 Remove the drop cable dummy rods

10.7 Horizontally place the Fig.8 cable and use cable

tie to fix the cable as shown.

10.8 Remove the excessive dummy rod and place the

remaining dummy rods back into its original

position.

10.9 Close the lid, screw the center screw and latch the

top cover, as shown.

Visit our website or contact your local CommScope ® representative for more information. www.commscope.com

FOSC, SMOUV, CommScope and all trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope,

This product may be covered by one or more U.S. patents or their foreign equivalents. For patents, see www.cs-pat.com

For technical assistance, customer service, or to report any missing/damaged parts, visit us at: http://www.commscope.com/SupportCenter.

Ce manuel convient aux modèles suivants

Autres manuels CommScope Matériel réseau

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Manuel utilisateur

CommScope

CommScope RUCKUS SmartZone 100 Manuel utilisateur

CommScope

CommScope SYSTIMAX AirSPEED AP542 Manuel utilisateur

CommScope

CommScope SYSTIMAX 360 iPatch G2 MPO Manuel utilisateur

CommScope

CommScope FPX Series Manuel utilisateur

CommScope

CommScope FOSC-OC-6 Manuel utilisateur

CommScope

CommScope M3200 Manuel utilisateur

CommScope

CommScope Uniprise Solutions HFTP-HD6B-1U-24 Manuel utilisateur

CommScope

CommScope MRJ21 Quick Fit Cassette Manuel utilisateur

CommScope

CommScope ION-M23 SDARS Manuel utilisateur

CommScope

CommScope ION-M7P Manuel utilisateur

CommScope

CommScope NOVUX DSC 650 Manuel utilisateur

CommScope

CommScope FPX Series Manuel utilisateur

CommScope

CommScope TC-96370-IP Manuel utilisateur

CommScope

CommScope SYSTIMAX EHD Manuel utilisateur

CommScope

CommScope SCIL-B Manuel utilisateur

CommScope

CommScope ONECELL RP5200 Manuel

CommScope

CommScope Constellation CPT-PP-48C Manuel utilisateur

CommScope

CommScope OneCell RP5000 Series Mode d’emploi

CommScope

CommScope ION-M7P Manuel utilisateur

CommScope

CommScope SD-4U-SPLICE PANEL Manuel utilisateur

CommScope

CommScope SYSTIMAX 100BASE-T Manuel utilisateur

CommScope

CommScope ION-M17EHP/19P Manuel utilisateur

CommScope

CommScope UNJ10G Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur