Lanner NCA-1020A Manuel utilisateur

NCA-1020 User Manual

NCA-1020

User Manual

Version: 1.6

Date of Release: 2019-09-06

Network

Computing

The icons are used in the manual to serve as an indication of interest topics or important messages. Below

is a description of these icons:

Note: This check mark indicates that there is a note of interest and is something that you should

pay special attention to while using the product.

Warning: This exclamation point indicates that there is a caution or warning and it is something

that could damage your property or product.

The listed websites are links to the online product information and technical support.

Resources

URL

Lanner

http://www.lannerinc.com

Product Resource

http://www.lannerinc.com/download-center

RMA

http://eRMA.lannerinc.com

proprietary and confidential to Lanner Electronics Inc. No part of this document may be reproduced in any

form or by any means or used to make any derivative work (such as translation, transformation, or

adaptation) without the express written consent of Lanner Electronics Inc. Lanner Electronics Inc. reserves

the right to revise this document and to make changes in content from time to time without obligation on

the part of Lanner Electronics Inc. to provide notification of such revision or change.

The information in this document is furnished for informational use only, is subject to change without

notice, and should not be construed as a commitment by Lanner Electronics Inc. Lanner Electronics Inc.

assumes no responsibility or liability for any errors or inaccuracies that may appear in this document or any

software that may be provided in association with this document.

Intel, Pentium, and Celeron are registered trademarks of Intel Corp.

Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.

All other product names or trademarks are properties of their respective owners.

NCA-1020 User Manual

This product has passed the CE test for environmental specifications. Test conditions for passing included

the equipment being operated within an industrial enclosure. In order to protect the product from being

damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of

CE-compliant industrial enclosure products.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a residential environment.This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment

in a commercial area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy, and if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. However, if this equipment does cause interference to radio or television equipment

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help.

Use a shielded and properly grounded I/O cable and power cable to ensure compliance of this unit to

the specified limits of the rules.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

Follow these guidelines to ensure general safety:

Keep the chassis area clear and dust-free during and after installation.

Do not wear loose clothing or jewelry that could get caught in the chassis. Fasten your tie or scarf and

roll up your sleeves.

Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.

Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

Disconnect all power by turning off the power and unplugging the power cord before installing or

removing a chassis or working near power supplies

Do not work alone if potentially hazardous conditions exist.

Never assume that power is disconnected from a circuit; always check the circuit.

Risk of Explosion if Battery is replaced by an incorrect type. Dispose of used batteries according to the

instructions.

Installation only by a trained electrician or only by an electrically trained person who knows all English

Installation and Device Specifications which are to be applied.

Do not carry the handle of power supplies when moving to another place.

The machine can only be used in a fixed location such as labs or computer facilities.

Electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment

to acceptable operating temperatures without adequate circulation. Be sure that the room in which you

choose to operate your system has adequate air circulation.

Ensure that the chassis cover is secure. The chassis design allows cooling air to circulate effectively. An

open chassis permits air leaks, which may interrupt and redirect the flow of cooling air from internal

components.

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs

when electronic components are improperly handled and can result in complete or intermittent failures.

Be sure to follow ESD-prevention procedures when removing and replacing components to avoid these

problems.

Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. If no wrist strap is

available, ground yourself by touching the metal part of the chassis.

Periodically check the resistance value of the antistatic strap, which should be between 1 and 10

megohms (Mohms).

NCA-1020 User Manual

Environment:

Do not install and/or operate this unit in any place that flammable objects are stored or used in.

Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient

temperature of the rack environment may be greater than room ambient. Therefore, consideration

should be given to installing the equipment in an environment compatible with the maximum ambient

temperature (Tma) specified by the manufacturer.

Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of airflow

required for safe operation of the equipment is not compromised.

Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition

is not achieved due to uneven mechanical loading.

Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of the circuits might have on over-current protection and supply

wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this

concern.

Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connections to the branch circuit (e.g.,

use of power strips).

Lanner Electronics Inc. shall not be held liable for any losses resulting from insufficient strength for

supporting the unit or use of inappropriate installation components.

Installation & Operation:

The installation of this product must be performed by trained specialists; otherwise, a non-specialist

might create the risk of the unit’s falling to the ground or other damages.

Lanner Electronics Inc. shall not be held liable for any losses resulting from insufficient strength for

supporting the unit or use of inappropriate installation components.

Suivez ces consignes pour assurer la sécurité générale :

Laissez la zone du châssis propre et sans poussière pendant et après l’installation.

Ne portez pas de vêtements amples ou de bijoux qui pourraient être pris dans le châssis. Attachez votre

cravate ou écharpe et remontez vos manches.

Portez des lunettes de sécurité pour protéger vos yeux.

N’effectuez aucune action qui pourrait créer un danger pour d’autres ou rendre l’équipement

dangereux.

Coupez complètement l’alimentation en éteignant l’alimentation et en débranchant le cordon

d’alimentation avant d’installer ou de retirer un châssis ou de travailler à proximité de sources

d’alimentation.

Ne travaillez pas seul si des conditions dangereuses sont présentes.

Ne considérez jamais que l’alimentation est coupée d’un circuit, vérifiez toujours le circuit. Cet appareil

génère, utilise et émet une énergie radiofréquence et, s’il n’est pas installé et utilisé conformément aux

instructions des fournisseurs de composants sans fil, il risque de provoquer des interférences dans les

communications radio.

Risque d’explosion si la pile est remplacée par une autre d’un mauvais type.

Jetez les piles usagées conformément aux instructions.

L’installation doit être effectuée par un électricien formé ou une personne formée à l’électricité

connaissant toutes les spécifications d’installation et d’appareil du produit.

Ne transportez pas l’unité en la tenant par le câble d’alimentation lorsque vous déplacez l’appareil.

La machine ne peut être utilisée qu’à un lieu fixe comme en laboratoire, salle d’ordinateurs ou salle de

classe.

L’équipement électrique génère de la chaleur. La température ambiante peut ne pas être adéquate pour

refroidir l’équipement à une température de fonctionnement acceptable sans circulation adaptée.

Vérifiez que votre site propose une circulation d’air adéquate.

Vérifiez que le couvercle du châssis est bien fixé. La conception du châssis permet à l’air de

refroidissement de bien circuler. Un châssis ouvert laisse l’air s’échapper, ce qui peut interrompre et

rediriger le flux d’air frais destiné aux composants internes.

Les décharges électrostatiques (ESD) peuvent endommager l’équipement et gêner les circuits

électriques. Des dégâts d’ESD surviennent lorsque des composants électroniques sont mal manipulés et

peuvent causer des pannes totales ou intermittentes. Suivez les procédures de prévention d’ESD lors du

retrait et du remplacement de composants.

Portez un bracelet anti-ESD et veillez à ce qu’il soit bien au contact de la peau. Si aucun bracelet n’est

disponible, reliez votre corps à la terre en touchant la partie métallique du châssis.

Vérifiez régulièrement la valeur de résistance du bracelet antistatique, qui doit être comprise entre 1 et

10 mégohms (Mohms).

Avant d’allumer l’appareil, reliez le câble de mise à la terre de l’équipement à la terre.

Une bonne mise à la terre (connexion à la terre) est très importante pour protéger l’équipement contre

les effets néfastes du bruit externe et réduire les risques d’électrocution en cas de foudre.

Pour désinstaller l’équipement, débranchez le câble de mise à la terre après avoir éteint l’appareil.

Un câble de mise à la terre est requis et la zone reliant les sections du conducteur doit faire plus de 4

mm2 ou 10 AWG.

NCA-1020 User Manual

Desserrez la vis du terminal de mise à la terre.

Branchez le câble de mise à la terre à la terre.

L’appareil de protection pour la source d’alimentation CC

doit fournir 30 A de courant.

Cet appareil de protection doit être branché à la source

d’alimentation avant l’alimentation CC.

Version

Date

Descriptions

1.0

2017/07/18

1st Draft

1.1

2017/09/29

Modified ToC

1.2

2017/11/30

Modified Front Panel and Connector Pin Assignments

1.3

2018/01/03

Modified Chapter 3: Board Layout

1.4

2018/07/09

Modified System Specifications

1.5

2019/02/13

Add Rack mount Kit

1.6

2019/09/06

Update Specifications and BIOS Setup

NCA-1020 User Manual

Package Content......................................................................................................................... 11

Ordering Information ................................................................................................................. 11

System Specifications ................................................................................................................. 12

Mechanical Drawing................................................................................................................... 13

Block Diagram............................................................................................................................. 15

Front Panel ................................................................................................................................. 16

Rear Panel................................................................................................................................... 17

Jumpers and Connectors on the Motherboard.......................................................................... 18

Jumper Setting and Connector Pin-out ...................................................................................... 20

Preparing the Hardware Installation.......................................................................................... 25

Installing the System Memory.................................................................................................... 27

Installing Mini-PCIe Modules...................................................................................................... 29

Installing Disk Drives................................................................................................................... 30

Installing SMA Antenna (optional) ............................................................................................. 32

Rackmounting the System (with the Adapter Holder)............................................................... 33

Main............................................................................................................................................ 36

Advanced Page ........................................................................................................................... 38

Chipset Page ............................................................................................................................... 54

Security....................................................................................................................................... 57

Boot Menu.................................................................................................................................. 60

Save and Exit Menu .................................................................................................................... 61

For Parallel Text-based LCM....................................................................................................... 65

Warranty Policy .......................................................................................................................... 69

RMA Service................................................................................................................................ 69

RMA Service Request Form ........................................................................................................ 70

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lanner Matériel réseau

Lanner

Lanner NCA-5210 Manuel utilisateur

Lanner

Lanner ICS-P570 Manuel utilisateur

Lanner

Lanner HCP-72i1 Manuel utilisateur

Lanner

Lanner NCA-4025 Manuel utilisateur

Lanner

Lanner ECA-4027 Manuel utilisateur

Lanner

Lanner NCA-1010 Manuel utilisateur

Lanner

Lanner NCA-6520 Manuel utilisateur

Lanner

Lanner LEC-3340 Manuel utilisateur

Lanner

Lanner NCR-1510 Manuel utilisateur

Lanner

Lanner NCA-2522 Manuel utilisateur

Lanner

Lanner FW-7580 Manuel utilisateur

Lanner

Lanner NCA-2512 Manuel utilisateur

Lanner

Lanner EAI-I130 Manuel utilisateur

Lanner

Lanner NCA-2510 Manuel utilisateur

Lanner

Lanner ICS-I372 Manuel utilisateur

Lanner

Lanner LWR-X8460 Manuel utilisateur

Lanner

Lanner ECA-4025 Manuel utilisateur

Lanner

Lanner FX-3230 Manuel utilisateur

Lanner

Lanner NCA-5230 Manuel utilisateur

Lanner

Lanner IIOT-I531 Manuel utilisateur

Lanner

Lanner IIOT-I530 Manuel utilisateur

Lanner

Lanner NCA-4210 Manuel utilisateur

Lanner

Lanner NCA-1525 Manuel utilisateur

Lanner

Lanner IIOT-I330 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur

Cantek

Cantek NR310-4 Manuel utilisateur