BCM RX965Q Manuel utilisateur

RX965Q

RX965Q

LGA775 Socket for Intel® Quad-core /Core™2 Extreme/

Core™2 Duo / Pentium® D / Pentium® 4 / Celeron® D uATX Motherboard

User’s Quick Start Card Version 1.02 http://www.bcmcom.com

Inspect the Package:

One RX965Q Motherboard

One 40-pin IDE cable

Two SATA Cables

Two SATA Power Cables

One I/O Shield

One Driver CD (Manual/Drivers)

One User’s Quick Start Card

Responsibility:

This manual is provided “As-Is” with no warranties of any kind, it will neither expressed or

implied, including, but not limited to the implied warranties or conditions of this product’s fitness

for any particular purpose. In no event shall we be liable for any loss of profits, loss of business,

loss of data, interruption of business, or indirect, special, incidental, or consequential damages

of any kind, even the possibility of such damages arising from any defect or error in this manual

or product. We reserve the right to modify and update the user manual without prior

notice.

ATTENTION: Incorrect BIOS Setup

If you do not know how to handle BIOS setup or how to set it up properly, it is strongly

advisable that you do not modify any of the settings than otherwise instructed in the User’s

Quick Start Card. Even a seemingly small incorrect adjustment or modification in the BIOS

setup can render your system unstable or unusable. The incorrect BIOS setup is not covered

by your motherboard’s manufacturer warranty.

Additional Information:

Additional information on setting this board up can be found in the User’s Manual in the

provided CD-ROM. The Online User’s Manual and FAQ/Knowledge Base can be found on

our website by visiting our website: http://www.bcmcom.com. If your question is not

answered in our FAQ/Knowledge Base, visit our forums and post your messages or submit a

new FAQ through FAQ Submittal form for us to add your question in our FAQ with our

answer.

Motherboard Layout:

Back Panel:

Board Layout:

WARNING: Electrostatic Sensitive Device (ESD)

Static electricity can easily damage your motherboard and will void your motherboard

warranty. Keep the motherboard and other system components in their anti-static packaging

until you are ready to install them. Touch a grounded surface before you remove any system

component from its protective anti-static packaging. Unpacking and installation should be

done on a grounded, anti-static mat. The operator should be wearing an anti-static

wristband, grounded at the same points as the anti-static mat. During configuration and

installation touch a grounded surface frequently to discharge any static electrical charge that

may have built up in your body. Avoid touching the components when handling the

motherboard or a peripheral card. Handle the motherboard and peripheral cards either by

the edges or by the peripheral card case-mounting bracket.

WARNING: Misplaced Jumper Damage

Incorrect setting jumpers and connectors may lead to damage to your motherboard and will

void your motherboard warranty. Please pay special attention not to connect these headers

in wrong directions. DO NOT change ANY jumpers while the motherboard has the power!

Connectors, Jumpers, & Headers

ATX Power Connectors (24-Pin ATXPWR1, JPW1 ):

Front Panel Connector (JFP1, JFP2):

Fan Power Connectors (CPUFAN1, SYSFAN1, PWRFAN1):

Intel ICH8DO SATA Controller Ports

(SATA1, SATA2, SATA3, SATA4, SATA5, SATA6):

IDE Connector (IDE1):

NOTE: 1. The IDE1 port is controlled through USB-to-IDE Controller chip, due to

to USB bandwidth limitation (480Mb/s or equivalent to 60MB/s), this

port cannot support UDMA 100 transfer rate, or IDE devices designed

to be operated at UDMA 100 mode only.

2. Due to the limitation of controller chip, OS cannot be installed or boot

from IDE hard drive connected to IDE1.

3. It is recommended to use IDE optical disk (e.g. CD/DVD-ROM) on IDE1.

Floppy Drive Connector (FDD1):

Serial Port Connector (JCOM1):

Front USB Headers (JUSB2, JUSB3):

Optical Drive Audio Connector (CD_IN1):

Front Panel Audio Connector (JAUD1):

Chassis Intrusion Connector (JCASE1):

Clear CMOS Jumper (JBAT1):

Table des matières

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur