BCM SQ575 Manuel utilisateur

SQ575 Pentium PCI

Mainboard

User’s Manual

SQ575

User‘s Notice

Static Electricity Precaution

Static electricity can easily damage your SQ575 mainboard. Observing a few basic

precautions can help you safeguard against damage that could result in expensive repairs.

Follow the simple measures below to protect your equipment from static electricity damage:

Keep the mainboard and other system components in their anti-static packaging until you are

ready to install them.

Touch a grounded surface before you remove any system component from its protective anti-

static packaging. Unpacking and installation should be done on a grounded, anti-static mat.

The operator should be wearing an anti-static wristband, grounded at the same points as the

anti-static mat.

After removing the mainboard from its original packing, only place it on a grounded, anti-

static surface component side up. Immediately inspect the board for damage. Due to shifting

during shipping, it is suggested that the installer press down on all of the socket IC‘s to ensure

they are properly seated. Do this only with the board placed on a firm flat surface.

During configuration and installation, touch a grounded surface frequently to discharge any

static electrical charge that may have built up in your body. The best precaution is to wear a

grounded wrist strap. When handling the mainboard or an adapter card avoid touching its

components. Handle the mainboard and adapter cards either by the edges or by the adapter

card’s case mounting bracket.

The information presented in this publication has been carefully screened for reliability. The

manufacturer provides this manual “As is” with no warranties of any kind, either expressed or

implied, including but not limited to the implied warranties or conditions of this product’s

fitness for any particular purpose. In no event shall the manufacturer be liable for any loss of

profits, loss of business, loss of data, interruption of business, or indirect, special, incidental,

or consequential damages of any kind, even if the manufacturer has been advised of the

possibility of such damages arising from any defect or error in this manual or product.

The manufacturer has the right to change this specification without pre-notice.

Trademarks and product names appearing in this manual are may or may not be registered

with their respective holders.

SQ575

This device complies with Part 15 of FCC Rules,

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

SQ575

Table of Contents

1INTRODUCTION......................................................................................... 1

1.1 OVERVIEW............................................................................................. 1

1.2 HOW TO USE THIS MANUAL ................................................................... 1

1.3 ITEM CHECKLIST.................................................................................... 1

2KEY FEATURES .......................................................................................... 1

2.1 PRODUCT SPECIFICATION....................................................................... 1

3INSTALLATION PREVIEW....................................................................... 1

3.1 JUMPER SETTINGS.................................................................................. 1

3.2 INSTALLATION OF DRAM MODULES (SIMM OR DIMM)...................... 5

3.3 INSTALLATION OF THE CPU................................................................... 9

3.4 INSTALLATION OF EXPANSION SLOTS:................................................. 10

3.5 INSTALLATION OF IDE, I/O CABLES CONNECTION ............................... 10

4BIOS SETUP.................................................................................................. 1

4.1 STARTING SETUP ................................................................................... 1

4.2 MAIN SETUP MENU ............................................................................... 3

4.3 STANDARD CMOS SETUP MENU........................................................... 4

4.4 BIOS FEATURES SETUP MENU.............................................................. 8

4.5 CHIPSET FEATURES SETUP MENU........................................................ 11

4.6 POWER MANAGEMENT SETUP MENU................................................... 12

4.7 PCI CONFIGURATION SETUP MENU..................................................... 15

4.8 INTEGRATED PERIPHERALS MENU ....................................................... 17

4.9 IDE HDD AUTO DETECTION............................................................... 19

4.10 PASSWORD SETTING......................................................................... 19

SQ575

1Introduction

1.1 Overview

The SQ575 mainboard integrates the Pentium microprocessor, memory, and I/O technologies

and is designed to fit into a standard AT form factor chassis. The design supports Pentium

processors, Pentium processors with MMX technology, Cyrix 6X86/6X86L/M2 Processors,

and AMD K5/K6 Processors. Page 2-2 illustrates the mechanical form factor for the SQ575

mainboard.

1.2 How to use this Manual

This manual provides information necessary to install and operate the SQ575 mainboard and

is organized into four chapters. The purpose of this manual is to explain the installation

procedures and operations of the mainboard as specified below.

1. Introduction Manual information and checklist

2. Key Features An overview specification of this mainboard

3. Installation Instructions on how to setup the mainboard

4. BIOS setup BIOS software setup information

1.3 Item Checklist

The SQ575 mainboard should contain following items (ü). Immediately, contact your retailer

if you discover any missing items, or any damage.

_The SQ575 mainboard

_This SQ575 user‘s manual

_1 IDE ribbon cable

_1 floppy ribbon cable

_1 parallel ribbbon cable attached to a mounting bracket

_2 serial ribbbon cable attached to a mounting bracket

_1 PS/2 cable with bracket (optional)

_USB (2 port) cable with bracket (optional)

_Infrared (IrDA) module with ribbon cable (optional)

SQ575

2Key Features

The SQ575 mainboard integrates the Pentium microprocessor, memory, and I/O technologies

and is designed to fit into a standard AT form factor chassis. Page 2-2 illustrates the

mechanical form factor for the SQ575 mainboard.

2.1 Product Specification

_Processor: Supports 90-233MHz Intel Pentium Processors (P54C), Pentium

Processors with MMX Technology (P55C), AMD-K5, AMD-K6 and Cyrix 6X86,

6X86L, M2 Processors. The ZIF Socket 7 will support future Pentium Overdrives.

_L2 Cache: Onboard 256KB or 512KB Pipeline Burst SRAM

_SIMM (System Memory): Supports 70ns or faster Extended Data Output (EDO) or

Fast Page (FP) SIMM in four 72-pin SIMM sockets using 4MB, 8MB, 16MB, 32MB or

64MB for a maximum of 256MB system memory.

_DIMM (System Memory): Supports 66MHz or faster 3.3V DIMM in two 168-pin

DIMM sockets using 1Mx64, 2Mx64, or 4Mx64 for a maximum of 256MB system

memory.

_Chipset: Intel Triton 430TX set is the core chipset with an Winbond 977 super I/O

controller chip.

_Expansion Slots: Four 32-bit PCI and Three 16-bit ISA expansions slots (one shared).

_Super Multi-I/O: Two high-speed UART compatible serial ports and One parallel port

with ECP and EPP compatibility. One FDD header supporting either 5.25“ or 3.5” (1.2

or 1.44/2.88MB) floppy drives. One IrDA TX/RX infrared port.

_PS/2 Mouse header: Onboard PS/2 Mouse Port

_PCI bus Master IDE Controller: Onboard dual-channel PCI Bus Master IDE support

4 IDE devices. This controller supports PIO Mode 3 and Mode 4 with a data transfer

rate up to 17MB per second. An Ultra DMA 33 (UDMA) supports data transfer rates up

to 33 MB per second. Also supports 120MB Floppy Drive.

_Universal Serial Bus (USB): Two standard USB interface supports up to 48MHz and

127 peripheral devices.

_PCI BIOS: Win 95 Plug and Play with Green power saving support, and DMI

Support.

Mechanical: Baby AT form factor 220 mm x 230 mm

Table des matières

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur