AWS AERO-100 Manuel utilisateur

American Weigh Scales

AERO-100 (100g x 0.01g)

AERO-650 (650g x 0.01g)

User Manual

AERO

AERO Manual

Thank you for purchasing the American Weigh AERO

digital pocket scale. Please read all operating instructions

carefully before use. Scales are precision measuring devices

and should always be handled with proper care. To ensure

years of reliable service, keep these simple tips in mind:

• Do not exceed the scale’s maximum capacity. This

scale has integrated overload protection, but any

overload protection has its limits!

• Avoid exposure to extreme heat or cold. Scales

perform best at normal room temperature. If

temperatures have changed dramatically, recalibration

may be necessary.

• Allow your scale to warm up for 30-60 seconds before

performing calibration (if available).

• Store your scale in a clean, dry location. Dust, dirt,

and moisture can accumulate on the weighing

sensors and electronics causing inaccuracy or

malfunction.

• Avoid using your scale in close proximity to strong

radio wave emitting devices such as cordless phones.

• Alwaysweighonaatandlevelsurface,freefrom

vibrations and drafts. The corner of a room is usually

the most stable.

• Gently apply all items to be weighed. Do not drop

items onto the weighing platform.

• Avoid dropping your scale. The warranty does not

cover damage due to rough treatment or overload.

• Checkthebatteriesrstifyouarehavinganytrouble

with your scale. This simple step can remedy most

scale issues.

• Calibration should be checked and adjusted

occasionally as part of routine scale maintenance.

I. Part List

1. Scale

2. Cover/Expansion Tray

3. AAA Batteries (x2)

II. Key Description

1. Mode Key - Changes the displayed unit of measure.

2. Tare Key - Re-zeros the scale. Used to remove the

weight of a tray or container.

3. Calibration Key - Enters calibration adjustment

mode.

4. Power Key - Turns the scale on or off.

Proper Battery Installation

1. 3.

Max: 100g d: 0.01g

CAL

Max: 100g d: 0.01g

CAL

AERO Manual

III. Battery Installation

Low batteries can cause inaccuracies in digital scales. If

youareexperiencingissueswithyourscale,rsttrynew

batteries. Most times, this will solve the problem.

1. Beforeusingthescaleforthersttime,check

the battery compartment and remove any plastic

insulation strips or packaging that may be in place to

prevent battery drainage during shipping/storage.

2. If you are replacing the batteries, make sure the

positive and negative contacts are properly aligned.

IV. Operation

1. Placethescaleonaat,levelsurfaceandpressthe

key to turn the scale on.

2. Once the start-up process completes and the scale

goes to zero you are ready to weigh.

3. Place the quantity to be weighed onto the weighing

platform.

4. Wait a couple seconds for the display to stabilize

before taking a weight reading.

5. To turn the scale OFF, press the key again.

V. Changing the Unit of Measure

1. Press the Mkey to change the scales displayed unit

of measure.

2. If the scale is turned off then back on, it will default

to the last unit used.

• AERO-100 & AERO-650 Units: g (gram) oz

(ounce) ozt (troy ounce) dwt (pennyweight) ct

(carat) gn (grain)

VI. Using the Tare Feature

You can use this scale’s tare feature to subtract the weight

of an empty container or vessel for net weight determination.

NOTE: The weight of the container will subtract from the

available capacity (subtractive taring).

1. Place the empty container or vessel on the weighing

platform.

2. Press the Tkey once. The display will then reset to

zero. If the container is removed, its weight will be

displayed as a negative number.

3. Youmaynowllthecontainerwiththequantityto

be weighed. The display will show the net weight of

the contents.

4. To return to normal weight display (gross weight),

remove any items from the weighing platform and

press the T key again to re-zero the scale.

VII. Calibration

Initial calibration is performed at the factory. However, the

calibration can drift slightly due to stresses from shipping.

Also, due to changes in local acceleration of gravity around

the world, adjustment is recommended when moving the

scale from one location to another. To check calibration:

1. Place the required calibration weight on the scale

and note the displayed value.

2. If the displayed value is not within acceptable

tolerance (see chart on next page), adjustment is

required.

AERO Manual

Model Acceptable

Tolerance (±)

Calibration

Weight

Recommended

Accuracy Class

AERO-100 0.02g 100g OIML M2

AERO-650 0.2g 500g OIML M2

VIII. Adjustment

1. Press the CAL button to enter calibration mode.

2. Make sure no weight is on the platform and press

the CAL key again to adjust the zero point. The

LCDwillash“CAL”followedbytherequiredspan

calibration weight (see chart above).

3. Place the required weight on the center of the scale

platform.Thedisplaywillash“PASS”thenreturnto

normal weighing. Adjustment is complete!

NOTE: Adjustment using the incorrect mass will

result in inaccurate readings.

IX. Troubleshooting

• Problem: Scale will not turn on

• Solution: Check the batteries and battery contacts.

• Problem: Displayedweightuctuatesrandomly

• Solution: Make sure your workspace is stable and

free of any air currents or vibration. In some cases,

nearby radio wave emitting devices can cause

uctuations.

• Problem: Displayed weight is inaccurate

• Solution: Perform a calibration adjustment. If

you are still having trouble, contact our warranty

department.

X. Error Codes

1. OUTZ - Zero point has drifted out of the acceptable

range. Try to perform a calibration adjustment. If the

problem persists, the load cell may be permanently

damaged due to overloading.

2. O-Ld - Overload. The maximum capacity has

been exceeded. Remove the extra weight to avoid

permanently damaging the load cell.

3. Lo - Batteries are low. Replace the batteries.

XI. Specications

AERO-100 AERO-650

Max. Capacity 100g 600g

Readability 0.01g 0.1g

Min. Weight 0.03g 0.2g

Power 2x1.5V“AAA”Alkaline

Dimensions 0.7 x 2.6 x 4.7 in.

Platform Dimensions 2.0 x 2.9 in.

Warranty 10 Year Limited Warranty

XII. Capacity/Readability Charts

AERO-100 AERO-650

100g x 0.01g

3.527oz x 0.001oz

3.215ozt x 0.001ozt

64.30dwt x 0.01dwt

500ct x 0.05ct

1543.2gn x 0.2gn

650g x 0.1g

22.92oz x 0.01oz

20.89ozt x 0.01ozt

417.95dwt x 0.1dwt

3250ct x 0.5ct

10031gn x 2gn

AERO Manual

American Weigh Scales, Inc.

Norcross, GA 30092

Made In China to our exact

specicationsandqualitycontrol.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AWS Échelle

Manuels Échelle populaires d'autres marques

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur

Fidelity Electronics

Fidelity Electronics G2e Manuel utilisateur