AWS LB-1000 Manuel utilisateur
American Weigh Scales, Inc.
LB-1000 User Manual
L B -1000
Compact Bowl Scale
g
LB-1000 Manual
Thank you for purchasing the American Weigh
LB-1000 digital scale. Please read all operating
instructions carefully before use. This electronic scale
is a precision instrument. With normal care and proper
treatment, it will provide years of reliable service.
Never load the scale with more than the maximum
capacity. Overloading will permanently damage it!
Avoid any exposure to extreme heat or cold. Your
scale works better when operated at normal room
temperature. Always allow the scale to acclimate to
normal room temperature for at least one hour before
use.
Give your scale sufcient warm up time. Usually
30-60 seconds before calibration to give the internal
components a chance to stabilize.
Keep your scale in a clean environment. Dust, dirt,
moisture, vibration, air currents and a close distance to
other electronic equipment can all cause an adverse
effect on the reliability and accuracy of your scale.
Handle with care. Gently apply all items to be weighed
onto tray top. Although this scale is designed to be
quite durable, try to avoid rough treatment as this may
permanently damage the internal sensor.
Avoid shaking, dropping or otherwise shocking the
scale. This is a precision instrument and must be
handled with extreme care.
Only operate the scale on a stable, vibration free
surface.
I. OPERATION
1. Press [ON/MEM] key.
2. Wait until “0.0” is displayed.
3. Put the object(s) on the weighing platform.
4. Using the [MODE/CAL] key, you can switch
between the weighing units.
II. TARE WEIGHING
1. Turn on scale as described above.
2. Place the “tare item” (ie. bowl) on the platform.
3. Press [TARE] and wait until “0.0” is displayed.
4. Add the “net-weight-item”.
Note: Turning the scale on with the tare item on the
weighingplatform achieves the same effect.
III. CALIBRATION
Calibration is NOT required before rst use. Only
calibrate if scale is not weighing properly.
1. Remove any items from the scale and press [ON/
MEM] to turn the scale on.
2. Wait til the scale zeros then press and hold the
[MODE/CAL] key until “400.0” is displayed.
3. Gently place the two 200g weights (included) onto
the weighing platform and wait 4 seconds. Do not
disturb the balance during this time.
4. If calibration is successful “F” will be displayed.
Otherwise, if the display shows “E”, an error has
occured and you should repeat calibration.
5. Press [TARE] to return to normal weighing mode.
IV. COUNTING FEATURE
1. To enter parts counting mode, press [CAL/MODE]
to scroll through the weighing modes until "C" appears
on the display. The minimum sample quantity is 5 and
will be displayed as "S=5"
2. Continue to press the [CAL/MODE] key to select the
desired parts counting unit: 5, 10, 20, 50 pieces. After
"50" is displayed the scale will cycle back to g (grams).
3. With the sample quantity value still displayed on the
LCD, place the actual sample quantity on the platform.
Allow the sample to stabilize for 3~5 seconds then
press [TARE]. The sample quantity is now set.
4. You can now add any number of the item on the
scale and a count will be displayed.
V. MEMORY FUNCTION
1. With the balance on, press the [TARE] key to
ensure the balance is zeroed.
2. Place an item on the scale and press [ON/MEM]
when the display is stable. This action adds the
displayed weight into the memory buffer which is
normally set to zero. The display will show "0.0" again.
3. Repeat step 2 above as many times as you need,
until you are ready to see the cummulative result.
4. To view the cummulative weight, press the [ON/
MEM] key. The total will be displayed and the memory
buffer will return to zero.
5. Press [TARE] to zero out the balance and the scale
is ready for normal weighing again.
VI. TROUBLESHOOTING
The primary reasons for inaccuracy or malfunction
are low batteries, incorrect calibration, overload or
operating on an unstable surface. Please keep this in
mind and maintain and operate your scale properly.
This scale is a precise instrument and must be
handled with the utmost care and caution.
[Display] Elimination of errors
Change the batteries.
You are overloading the scale. Remove
the excess weight immediately to prevent
damage to the internal load cell.
There was a calibration error. Repeat
calibration.
Specications
Model LB-1000
Capacity 1000g / 35.27oz / 32.15ozt / 643.1dwt
Resolution 0.1g / 0.005oz / 0.005ozt / 0.05dwt
Weighing Units grams (g), ounces (oz), troy ounces (ozt), pennyweights (dwt)
Display 4 - Digit Backlit LCD
Calibration Weights
(Included) two (2) x 200g
Platform Dimensions
(inches) 5-1/8 diameter
Scale Dimensions
(inches) 5.5 x 7.25 x 1.5
Power 4 x AA (included)
Weight 1.0 lb
Autres manuels pour LB-1000
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels AWS Échelle
AWS
AWS AMW-810 Manuel utilisateur
AWS
AWS BLADE-50 Manuel utilisateur
AWS
AWS MSC-200 Manuel utilisateur
AWS
AWS AMW-Card120 Manuel utilisateur
AWS
AWS SR-1KG Manuel utilisateur
AWS
AWS MSC-100 Manuel utilisateur
AWS
AWS OM-200 Manuel utilisateur
AWS
AWS PEPPER-5K Manuel utilisateur
AWS
AWS 5K-BOWL Manuel utilisateur
AWS
AWS QS-500 Manuel utilisateur
AWS
AWS PN-Series Manuel utilisateur
AWS
AWS CQ-350 Manuel utilisateur
AWS
AWS LB-1000 Manuel utilisateur
AWS
AWS PC Series Manuel utilisateur
AWS
AWS SG-300 Manuel utilisateur
AWS
AWS AMW-DISC-55 Manuel utilisateur
AWS
AWS ZEO-50 Manuel utilisateur
AWS
AWS DigiPEN-500 Manuel utilisateur
AWS
AWS PNX-203 Manuel utilisateur
AWS
AWS BT2 series Manuel utilisateur
