AWS MiniCD MCD-100 Manuel utilisateur
American Weigh Scales
MCD-100 (100 x 0.01g
MCD-500 (500 x 0.1g)
User Manual
MiniCD
Copyright © 2010 American Weigh Scales, Inc.
All rights reserved. Rev. 2.0
MiniCD User Manual
Thank you for purchasing the American Weigh MiniCD
digital pocket scale. Please read all operating instructions
carefully before use. Scales are precision measuring devices
and should always be handled with proper care. To ensure
years of reliable service, keep these simple tips in mind:
• Do not exceed the scales maximum capacity.
Overloading your scale can permanently damage it!
• Avoid exposure to extreme heat or cold. Scales
perform best at normal room temperature. If
temperatures have changed dramatically, recalibration
may be necessary.
• Allow your scale to warm up for 30-60 seconds before
performing calibration (if available).
• Store your scale in a clean, dry location. Dust, dirt,
and moisture can accumulate on the weighing
sensors and electronics causing inaccuracy or
malfunction.
• Avoid using your scale in close proximity to strong
radio wave emitting devices such as computers, cash
registers, and cordless phones.
• Alwaysweighonaatandlevelsurface,freefrom
vibrations and drafts. The corner of a room is usually
the most stable.
• Gently apply all items to be weighed. Do not drop
items onto the weighing platform.
• Avoid dropping your scale. The warranty does not
cover damage due to rough treatment or overload.
• Checkthebatteriesrstifyouarehavinganytrouble
with your scale. This simple step can remedy most
scale issues.
• Do not disassembled your scale. This product
contains no user serviceable parts.
I/O M T L
I. Part List
1. Scale
2. Vinyl Carrying Pouch
3. CD Insert (x5)
4. User Manual and Terms and Conditions
5. C2032 Lithium Batteries (x2)
II. Key Description
III. Battery Installation
1. Beforeusingthescaleforthersttime,check
the battery compartment and remove any plastic
insulation strips or packaging that may be in place to
prevent battery drainage during shipping/storage.
2. When installing the batteries, make sure the positive
and negative contacts are properly aligned.
Install Negative
Side Up
Install Positive
Side Up
Negative Terminal
Postive Terminal
CR2032 (Button Cell) Battery Installation
+
-
+
-
Install Negative
Side Up
Install Positive
Side Up
Negative Terminal
Postive Terminal
CR2032 (Button Cell) Battery Installation
+
-
+
-
Mode Key
ON/OFF Key
Tare Key
Backlight
LCD Screen
I/O M T L
MiniCD User Manual
IV. Operation
1. Placethescaleonaat,levelsurfaceandpressthe
I/O key to turn the scale on.
2. Once the start-up process completes and the scale
goes to zero you are ready to weigh.
3. Place the quantity to be weighed onto the weighing
platform.
4. Wait a couple seconds for the display to stabilize
before taking a weight reading.
5. You can disable/enable the backlight by pressing
the Lkey.
V. Changing the Unit of Measure
1. Press the Mkey to change the scale’s displayed unit
of measure.
2. If the scale is turned off then back on, it will default
to the last unit used.
• MCD-100 Units: g (gram) oz (ounce) ct (carat)
gn (grain)
• MCD-500 Units: g (gram) oz (ounce) ozt (troy
ounce) dwt (pennyweight)
VI. Using the Tare Feature
You can use this scale’s tare feature to subtract the weight
of an empty container or vessel for net weight determination.
NOTE: The weight of the container will subtract from the
available capacity.
1. Place the empty container or vessel on the weighing
platform.
2. Press the Tkey once. The display will then reset to
zero. If the container is removed, it’s weight will be
displayed as a negative number.
3. Youmaynowllthecontainerwiththequantityto
be weighed. The display will show the net weight of
the contents.
4. To return to normal weight display (gross weight),
remove any items from the weighing platform and
press the T key again to re-zero the scale.
VII. Calibration
Calibration and adjustment are performed at the factory.
However, the weighing range can shift slightly during
shipping. Also, due to changes in local acceleration of gravity
around the world, adjustment is recommended when moving
the scale from one location to another. To check calibration:
1. Place the required calibration weight on the scale
and note the displayed value.
2. If the displayed value is not within acceptable
tolerance (see chart below), adjustment is required.
Model Acceptable
Tolerance (±)
Calibration
Weight
Recommended
Accuracy Class
MCD-100 0.02g 100g OIML M2
MCD-500 0.2g 500g OIML M2
VIII. Calibration Adjustment
1. Press and hold the Mkey until the display shows
“CAL”.
2. Press the Mkeyagain.Thedisplaywillash“CAL”
followed by the calibration weight value (see chart).
3. Place the calibration weight on the center of the
weighing platform. Make sure you are using the
correctweightforyourspecicmodel.
MiniCD User Manual
4. Once the weight is accepted, the display will show
“PASS” then return to normal operation.
IX. Troubleshooting
• Problem: Scale will not turn on
• Solution: Check the batteries
• Problem: Displayedweightuctuatesrandomly
• Solution: Make sure your workspace is stable and
free of any air currents or vibration
• Problem: Displayed weight is inaccurate
• Solution: Perform a calibration adjustment
X. Error Codes
1. OUTZ - Zero range has shifted. Perform calibration
adjustment. If the problem persists, the load cell may
be permanently damaged due to overloading.
2. 88888 - Maximum capacity exceeded. Remove the
extra weight to avoid damaging the load cell.
3. L - Batteries are low. Replace the batteries.
MCD-100 MCD-500
Max. Capacity 100g 500g
Readability 0.01g 0.1g
Power 2 x CR2032 Lithium
Dimensions 2.3 x 2.3 x 1.0 in.
Platform Dimensions 1.3 x 2.3 in.
Warranty 10 Year Limited Warranty
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels AWS Échelle
AWS
AWS DK-5K Manuel utilisateur
AWS
AWS NutriBalance-5000 Manuel utilisateur
AWS
AWS LB-1000 Manuel utilisateur
AWS
AWS SR-1KG Manuel utilisateur
AWS
AWS QS-500 Manuel utilisateur
AWS
AWS CARD-V2 Manuel utilisateur
AWS
AWS H-11 Manuel utilisateur
AWS
AWS SR-1KG Manuel utilisateur
AWS
AWS BT2 series Manuel utilisateur
AWS
AWS MDI-20 Manuel utilisateur
AWS
AWS ACPro-200 Manuel utilisateur
AWS
AWS Blade-50 Manuel utilisateur
AWS
AWS CUBE-100 Manuel utilisateur
AWS
AWS AC-650 Manuel utilisateur
AWS
AWS ACP-200 Manuel utilisateur
AWS
AWS VANILLA-5K Manuel utilisateur
AWS
AWS MB-100 Manuel utilisateur
AWS
AWS SM-200 Manuel utilisateur
AWS
AWS ES-250 Manuel utilisateur
AWS
AWS LB-1000 Manuel utilisateur
