AWS Blade-v2-50 Manuel utilisateur

American Weigh Scales, Inc.

BLADE-V2-50

BLADE-V2-100

BLADE-V2-400

User Manual

BLADE V2.0

Digital Pocket Scale

Blade Scale® V2.0 Manual

Thank you for purchasing the American Weigh Blade

Scale® V2.0 digital scale. Please read all operating

instructions carefully before use. This electronic scale

is a precision instrument. With normal care and proper

treatment, it will provide years of reliable service.

Never load the scale with more than the maximum

capacity. Overloading will permanently damage it!

Avoid any exposure to extreme heat or cold. Your

scale works better when operated at normal room

temperature. Always allow the scale to acclimate to

normal room temperature for at least one hour before

use.

Give your scale sufcient warm up time. Usually

30-60 seconds before calibration to give the internal

components a chance to stabilize.

Keep your scale in a clean environment. Dust, dirt,

moisture, vibration, air currents and a close distance to

other electronic equipment can all cause an adverse

effect on the reliability and accuracy of your scale.

Handle with care. Gently apply all items to be weighed

onto tray top. Although this scale is designed to be

quite durable, try to avoid rough treatment as this may

permanently damage the internal sensor.

Avoid shaking, dropping or otherwise shocking the

scale. This is a precision instrument and must be

handled with extreme care.

Only operate the scale on a stable, vibration free

surface.

I. OPERATION

Place Scale on a horizontal at surface.

1. Press the [ ] key.

2. Wait until "0.0” is displayed.

3. Put the object(s) on the weighing platform.

4. Using the [

] key, you can switch between the

weighing units.

II. TARE WEIGHING

1. Turn on scale as described above.

2. Place the "tare item" on the platform.

3. Press [

] and wait until "0.0" is displayed.

4. Add the "net-weight-item".

III. CALIBRATION

Calibration is NOT required before rst use. Only

calibrate if scale is not weighing properly.

**Make sure you use the correct calibration weight for

your scale or the calibration will not be accurate**

BLADE-v2-50: 50g calibration weight

BLADE-v2-100: 100g calibration weight

BLADE-v2-400: 200g calibration weight

1. Turn OFF the scale.

2. Press the [ ] key, then quickly press and hold

the [

] key until "CAL" is displayed. You may now

release the [

] key.

3. Press [

] again. The display will show "CAL"

followed by the required calibration weight (see

above).

4. Place the required calibration weight onto the center

of the platform. Wait 3-4 seconds. The display should

show "PASS", then return to normal weighing.

5. Remove the weight and press [ ] to turn the scale

off. Calibration is complete!

V. TROUBLESHOOTING

The primary reasons for inaccuracy or malfunction

are low batteries, incorrect calibration, overload or

operating on an unstable surface. Please keep this in

mind and maintain and operate your scale properly.

This scale is a precise instrument and must be

handled with the utmost care and caution.

[Display] Elimination of errors

-----------------------------------------------

[Lo] Change the batteries.

[OUT2] Recalibrate the scale as shown above.

[O_Ld] You are overloading the scale. Remove the

excessive load immediately!

[UnST] Use the scale in a more stable position

Model Blade-v2-50 Blade-v2-100 Blade-v2-400

Capacity 50.00g

1.764oz

250.00ct

771.5gn

100.00g

3.528oz

500.00ct

1543.2gn

400.0g

14.11oz

12.86ozt

257.2dwt

Resolution 0.01g

0.001oz

0.05ct

0.1gn (0.2gn minimum)

0.01g

0.001oz

0.05ct

0.1gn (0.2gn minimum)

0.1g

0.01oz

0.01ozt

0.1dwt

Weighing Units g, oz, ct, gn g, oz, ozt, dwt

Calibration Weight (not Included) 50g 100g 200g

Platform Dimensions (inches) 2.75 x 2.75 (Stainless Steel )

Scale Dimensions (inches) 2.9 x 2.9 x 0.7

Power 2 x AAA Batteries (included)

Warranty 10 Year Warranty

Specications

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AWS Échelle

Manuels Échelle populaires d'autres marques

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur

Fidelity Electronics

Fidelity Electronics G2e Manuel utilisateur