Advantech PCM-3614I Manuel d'installation et d'exploitation

1 Startup Manual All product specifications are subject to change without notice.

STARTUP MANUAL

PCM-3614I/3618I

4/8-port RS-232/422/485 Module

The PCM-3614I/3618I is a PCI-104 compatible

module with 4/8 individually configurable RS-232/

422/485 ports. The PCM-3614I/3618I also features

high transmission speeds, independent/shared

IRQ’s, a high-performance 16C550 UART

communication chip with 16-byte FIFO to reduce

CPU load, and more. These function settings

include Standard/Enhance, Independent/Shared IRQ

& Speed modes.

We carefully inspected the PCM-3614I/3618I both

mechanically and electrically before we shipped it.

It should be free of marks and scratches and in per-

fect electrical order on receipt.

Handle the board only by its edges. The static

charge on your body may damage its integrated cir-

cuits. Keep the card in its anti-static package when-

ever it is not installed. You can use this package to

return the card if it should need repair.

• 4/8 Independent RS-232/422/485 serial ports

• Automatic RS-485 data flow control

• Transmission speeds up to 921.6 Kbps

• Shared IRQ settings for each port

• Built-in terminal resistors

• LED indicators: TX, RX

• Bus interface: PCI-104

• Number of ports: 4/8

• UART: 16C550

• IRQ: 3, 4, 5, 6, 7, 9, 10, 11, 12, 15

• Data bits: 5, 6, 7, 8

• Stop bits: 1, 1.5, 2

• Parity: none, even, odd

• Speed (bps): 50 ~ 921.6K

• Connectors: DB-9 male

• Signal:

RS-422: TxD+, TxD-, RxD+, RxD-, GND,

CTS+, CTS-, RTS+ and RTS-

RS-485: DATA-, DATA+, GND

RS-232: TxD, RxD, RTS, CTS, DTR, DSR,

DCD, RI, GND

• Operating Temperature: 0 ~ 65° C ( 32~149° F)

• Storage Temperature: -25 ~ 80° C (-13~176° F)

• Operation Humidity: 0% ~ 90%

Relative Humidity, non-condensing

Card Configuration

The max configuration for the PCI bus of PCI-104

modules is FOUR plus the host board. If you stack

more than one PCI-104 module to a host board be

sure to set the modules to different PCI numbers

through SW2.

SW2 Settings

SW3/ SW4 Settings

Introduction Specifications

Initial Inspection

Features

Notes

For more information on this and other Advantech

products, please visit our websites at:

http://www.advantech.com

http://www.advantech.com/eAutomation

For technical support and service:

http://www.advantech.com/support/

This startup manual is for PCM-3614I/3618I.

Part No: 2003M61801 2nd Edition

February 2009

1 2 PCI Number

OF OFF 0

ON OFF 1

OFF ON 2

ON ON 3

SW3 SW4

CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

ON ON ON ON ON ON ON ON

Auto Auto Auto Auto Auto Auto Auto Auto

ON: Always high or low status for RS-422 mode (RS-422

Master)

OFF( Auto): Automatically sense direction of data flow for

RS-485 (RS-422 Slave)

2 Startup Manual

Hardware Installation

Installing the Module on a CPU Card:

1. Turn the PC power off. Turn the power off to any

peripheral devices such as printers and monitors.

2. Disconnect the power cord and any other cables from

the back of the computer.

3. Remove the system unit cover

4. Remove the CPU card from the chassis (if necessary)

to gain access to the card’s PCI-104 connector.

5. Screw the brass spacer (included with the module)

into the threaded hole on the CPU card. Do not

tighten too much, or the threads may be damaged.

6. Carefully align the pins of the PCM-3614I/3618I

with the PCI-104 connector. Slide the module into

the connector, do not push too hard.

7. Secure the module to the CPU card to the threaded

hole in the CPU card using the included screw.

8. Attach any accessories to the PCM-3614I/3618I.

9. Reinstall the CPU card and replace the system unit

cover. Reconnect the cables you removed in step 2.

10. Turn the power on.

Connecting to Another PCI-104 Module:

1. Insert the pins of connector CN15 into the piggy-

back connector on the other PCI-104 module.

2. Screw the PCM-3614I/3618I to the brass spacer. This

completes the hardware installation

Pin Assignments and Jumper Settings

The function of PCM-3614I/3618I is adjustable by the

CN1/CN2/CN3/CN4 jumper.

Jumper Settings of CN1/CN2/CN3/CN4

CN and COM Port Mapping

The following table and figure shows pin assignments

for the DB9 connector.

Pin Assignments of RS-232 DB9 Connector

Pin Assignments of RS-422/485 DB9 Connector

Pin Assignments of RS-422/485 Configuration

Warning! Turn off PC whenever you install, remove connect

or disconnect cables to PCM-3614I/3618I

Jumper Settings Function

Set the port at RS-232

mode.

Set the port at RS-422/

485 mode.

CN Number COM Port Number

Pin RS-232

1 DCD

2RxD

3TxD

4DTR

5GND

6DSR

7RTS

8CTS

9RI

Pin RS-422/485

1 TX-(DATA-)

2 TX+(DATA+)

3RX+

4RX-

5GND

6RTS-

7RTS+

8CTS+

9CTS-

Pin Description Pin Description

Port 0

Data- 1 TX- 2 RTS-

Data+ 3 TX+ 4 RTS+

5RX+ 6CTS+

7RX- 8CTS-

9 GND 10 NC

Port 1

Data- 11 TX- 12 RTS-

Data+ 13 TX+ 14 RTS+

15 RX+ 16 CTS+

17 RX- 18 CTS-

19 GND 20 NC

Port 2

Data- 21 TX- 22 RTS-

Data+ 23 TX+ 24 RTS+

25 RX+ 26 CTS+

27 RX- 28 CTS-

29 GND 30 NC

Port 3

Data- 31 TX- 32 RTS-

Data+ 33 TX+ 34 RTS+

35 RX+ 36 CTS+

37 RX- 38 CTS-

39 GND 40 NC

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Advantech Unité de contrôle

Advantech

Advantech ADAM-2000 Series Manuel utilisateur

Advantech

Advantech EPD-130 Manuel utilisateur

Advantech

Advantech ADAM-6051 Manuel utilisateur

Advantech

Advantech PCL-832 Manuel utilisateur

Advantech

Advantech MIO-6254 Manuel d'installation et d'exploitation

Advantech

Advantech PCM-3614 Manuel utilisateur

Advantech

Advantech ADAM-3016 Manuel utilisateur

Advantech

Advantech Network Device USB-4761 Manuel d'installation et d'exploitation

Advantech

Advantech ADAM-6217 Manuel utilisateur

Advantech

Advantech ADAM-3017 Manuel d'installation et d'exploitation

Advantech

Advantech ADAM-5240 Manuel utilisateur

Advantech

Advantech AIW-357 DK-G1P Manuel utilisateur

Advantech

Advantech Qseven SOM-3567 Manuel utilisateur

Advantech

Advantech SOM-5892 Manuel utilisateur

Advantech

Advantech MIO-6255 Manuel d'installation et d'exploitation

Advantech

Advantech IPMI-1000 Manuel d'installation et d'exploitation

Advantech

Advantech WISE-1840 Manuel utilisateur

Advantech

Advantech EPD-132 Manuel utilisateur

Advantech

Advantech PCM-23C1CF Manuel utilisateur

Advantech

Advantech IPMI-1000 Manuel d'installation et d'exploitation

Advantech

Advantech USB-4716 Manuel utilisateur

Advantech

Advantech ADAM-3750 3-Wire Series Manuel d'installation et d'exploitation

Advantech

Advantech WISE-1510 Manuel utilisateur

Advantech

Advantech EDG-4100 Series Guide de démarrage rapide

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur