Advantech PCM-3524 Manuel utilisateur

PCM-3524

VGA-to-TV PC/104 Module

Users Manual

PCM-3524 User’s Manual ii

nal manufacturer reserves the right to make improvements to the products

described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmit-

ted in any form or by any means without the prior written permission of

the original manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original manufacturer

assumes no responsibility for its use, nor for any infringements upon the

rights of third parties that may result from such use.

Acknowledgements

Award is a trademark of Award Software International, Inc.

VIA is a trademark of VIA Technologies, Inc.

IBM, PC/AT, PS/2 and VGA are trademarks of International Business

Machines Corporation.

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows® is a registered trademark of Microsoft Corp.

RTL is a trademark of Realtek Semi-Conductor Co., Ltd.

ESS is a trademark of ESS Technology, Inc.

UMC is a trademark of United Microelectronics Corporation.

SMI is a trademark of Silicon Motion, Inc.

Creative is a trademark of Creative Technology LTD.

All other product names or trademarks are properties of their respective

owners.

For more information on this and other Advantech products, please visit

our websites at: http://www.advantech.com

http://www.advantech.com/epc

For technical support and service, please visit our support website at:

http://support.advantech.com

This manual is for the PCM-3524.

Part No. 2006352400

1st Edition, Printed in Taiwan August, 2002

iii

FCC Class B

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a residential environment. This

equipment generates, uses and can radiate radio frequency energy. If not

installed and used in accordance with this user's manual, it may cause

harmful interference to radio communications. Note that even when this

equipment is installed and used in accordance with this user's manual,

there is still no guarantee that interference will not occur. If this equip-

ment is believed to be causing harmful interference to radio or television

reception, this can be determined by turning the equipment on and off. If

interference is occurring, the user is encouraged to try to correct the inter-

ference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment to a power outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Warning! Any changes or modifications made to the

equipment which are not expressly approved by

the relevant standards authority could void your

authority to operate the equipment.

PCM-3524 User’s Manual iv

Packing List

Before you begin installing your card, please make sure that the following

materials have been shipped:

• 1 ea. PCM-3524 module x 1 pc

• 4 ea. Screws (3mm) x 4 pcs

• 4 ea. Bronze stick (6mm) x 4 pcs

• 1 ea. D-sub 15 to D-sub 15 cable

• 1 ea. User's manual

If any of these items are missing or damaged, contact your distributor or

sales representative immediately.

Additional Information and Assistance

Step 1. Visit the Advantech web site at www.advantech.com where you

can find the latest information about the product.

Step 2. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before

you call:

• Product name and serial number

• Description of your peripheral attachments

• Description of your software (operating system, version, application

software, etc.)

• A complete description of the problem

• The exact wording of any error messages

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User's Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp

cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or let-

ting it fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment

from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power

source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according

to the user's manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE

THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR

ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE

EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.

16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY

REPLACED.REPLACE ONLY WITH THE SAME OR EQUIVALENT

TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED

BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUC-

TIONS.

The sound pressure level at the operator's position according to IEC 704-1:1982 is

no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan-

tech disclaims all responsibility for the accuracy of any statements contained

herein.

PCM-3524 User’s Manual vi

W i c h t i g e S i c h e r h e i s h i n w e i s e

1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie

Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch

zur Reinigung.

4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht

zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen

oder Fallen könnte Verletzungen hervorrufen.

7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhit-

zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.

8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.

9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.

Es sollte auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu

beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom

Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädi-

gung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten

in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus-

lösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen

Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen

und von einer qualifizierten Servicestelle zu überprüfen:

a - Netzkabel oder Netzstecker sind beschädigt.

b - Flüssigkeit ist in das Gerät eingedrungen.

c - Das Gerät war Feuchtigkeit ausgesetzt.

d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert

oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.

e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batte-

rie.Ersatz nur durch densellben order einem vom Hersteller empfohlene-

mahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des

Herstellers.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000

beträgt 70dB(A) oder weiger.

DISCLAIMER: This set of instructions is given according to IEC704-1.

Advantech disclaims all responsibility for the accuracy of any statements

contained herein.

vii

Contents

Chapter 1 General Information ........................................2

1.1 Introduction ....................................................................... 2

1.2 Features ............................................................................. 2

1.3 Board Layout..................................................................... 3

1.3.1 Placement ....................................................................... 3

Figure 1.1:Component Placement................................... 3

1.3.2 Module Dimensions ....................................................... 4

Figure 1.2:Dimensions.................................................... 4

Chapter 2 Installation ........................................................6

2.2 Jumper Settings ................................................................. 7

Table 2.1:Jumpers........................................................... 7

2.2.1 PAL/NTSC Video Output Select (JP1, JP2, JP4):.......... 7

Table 2.2:Output Mode Settings..................................... 7

2.2.2 PWRDN Power-Down Control (JP5)............................. 8

2.2.3 RGB_OUT Enable (JP6) ................................................ 8

2.2.4 YUV_OUT Enable (JP8) ................................................ 8

2.2.5 POWER Selection (JP14) ............................................... 8

2.3 Connectors......................................................................... 9

Table 2.3:Connectors...................................................... 9

2.3.1 VGA Connector (CN2/CN3 16-pin)............................... 9

2.3.2 VGA Connector (CN1/CN4 15-pin)............................. 10

2.3.3 Composite Video Output Connector (CN5/J1)............. 10

2.3.4 DC Power Connector (CN6)......................................... 10

2.3.5 DC Power Connector Jack (J2)..................................... 10

2.3.6 S-Video Output Connector (CN7/J3) ........................... 10

2.4 Switches and VR ............................................................. 11

Table 2.4:Switches........................................................ 11

2.4.1 Reset (SW1).................................................................. 11

2.4.2 Position controls (SW2~5)............................................ 11

Table 2.5:Position Adjustment Switches ...................... 11

2.4.3 ZOOM TOGGLE (SW6) .............................................. 12

2.4.4 BLANK (SW7)............................................................. 12

2.4.5 FREEZE (SW8) ............................................................ 12

2.4.6 FILTER MODE SELECTION (SW9).......................... 12

2.4.7 OVERSCAN (SW10) ................................................... 12

2.4.8 BRIGHTNESS (VR1)................................................... 12

2.5 Implementation of the PCM-3524................................... 13

2.5.1 Standalone..................................................................... 13

2.5.2 Plugged into Single Board Computer .......................... 13

PCM-3524 User’s Manual viii

1 Chapter1

CHAPTER

General Information

This chapter gives background

information on the PCM-3524 VGA-

to-TV PC/104 Module.

Sections include:

• Introduction

• Features

• Board Layout

PCM-3524 User’s Manual 2

Chapter 1 General Information

1.1 Introduction

The PCM-3524 converts RGB video and sync from a standard VGA

source into broadcast quality NTSC or PAL video. Composite and S-

Video outputs are compliant with SMPTE-170M and CCIR-656 specifi-

cations. A fully integrated 3-line adaptive flicker filter provides three

selectable operating modes. The PCM-3524 conforms to NTSC and PAL

standards using a single low-cost application circuit. Included is all of the

active circuitry required to generate a television signal with outstanding

image quality in a standalone application. Incoming VGA source signals

must be within a ±2% tolerance of 2X the frame and 2X the line rate of

the outgoing TV standard.

1.2 Features

• Flicker free VGA-to-TV signal converter

• 3-Channel 8 bit input conversion

• Multiple input formats: 640x480 60/75/85Hz, 800x600 60/75 Hz,

1024x768 60 Hz

• Multiple output formats - NTSC, NTSC-EIA, PAL-B/G/H/I

• Composite and S-video output formats

• Horizontal and vertical positioning control

• Configuration set by switches

• Internal color bars

• 3-Channel 9-bit output D/A converters

• Blanks to blue or black screen

Table des matières

Autres manuels Advantech Unité de contrôle

Advantech

Advantech PCM-233A Manuel d'installation et d'exploitation

Advantech

Advantech PCM-3664 Manuel d'installation et d'exploitation

Advantech

Advantech PCM-3531 Manuel d'installation et d'exploitation

Advantech

Advantech B+B SmartWorx 232PTC9 Manuel utilisateur

Advantech

Advantech PCA-TPMSPI Manuel d'installation et d'exploitation

Advantech

Advantech ADAM-2000 Series Manuel utilisateur

Advantech

Advantech B+B SmartWorx iMcV-Giga-MediaLinX TX/SFP Manuel utilisateur

Advantech

Advantech AIW-357 DK-G2U Manuel utilisateur

Advantech

Advantech PCM-3526 Manuel d'installation et d'exploitation

Advantech

Advantech PCM-3345 Manuel utilisateur

Advantech

Advantech PCM-3718 Series Manuel utilisateur

Advantech

Advantech ADAM-6051 Manuel utilisateur

Advantech

Advantech Adam 4000 Series Manuel utilisateur

Advantech

Advantech Network Device USB-4761 Manuel d'installation et d'exploitation

Advantech

Advantech PCM-3680 Manuel d'installation et d'exploitation

Advantech

Advantech USB-4716 Manuel utilisateur

Advantech

Advantech WISE-4671 Manuel d'installation et d'exploitation

Advantech

Advantech INTRAC INTRAC-305 Mode d’emploi

Advantech

Advantech SOM-5780 Mode d’emploi

Advantech

Advantech WISE-1510 Manuel utilisateur

Advantech

Advantech VEGA-330 Manuel d'installation et d'exploitation

Advantech

Advantech USB-5801 Manuel d'installation et d'exploitation

Advantech

Advantech EWM-W179M201E Manuel utilisateur

Advantech

Advantech Network Device USB-4761 Manuel d'installation et d'exploitation

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur