Advantech USB-5801 Manuel d'installation et d'exploitation

USB-5801 Startup Manual 1

Before installation, please ensure that the following items

are included with the product:

• 1 x USB-5801 module

• 4 x Terminal blocks

• 1 x USB 3.0 lockable cable (1 m)

• 1 x USB-5801 startup manual

If any of the above items are missing or damaged, contact

your distributor or sales representative immediately

User Manual

For more detailed information regarding this product, please

download the USB-5801 user manual from the Advantech

website.

USB-5801 is a highly accurate dynamic signal acquisition

USB 3.0 module speciﬁcally designed for vibration and

acoustic measurements. The module provides four simulta-

neously sampled 24-bit IEPE sensor inputs with an up to 192

kS/s sample rate for high-resolution measurements. USB-

5801 is also equipped with two 24-bit analog outputs with an

up to 192 kS/s update rate and two tachometer inputs whose

data can be correlated to the sensor data. The built-in USB

hub makes this module daisy chainable with other USB-5000

series products.

USB-5801

4-Ch, 24-Bit, 192 kS/s

Dynamic Signal Acquisition

USB

3.0 I/O Module with Analog Output and Tachometer

Startup Manual

FCC Class A

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15

of the FCC rules. These limits are designed to provide rea-

sonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause interference. In such cases, users are

required to correct the interference at their own expense.

This product has passed the CE test for environmental speci-

ﬁcations when shielded cables are used for external wiring.

We recommend the use of shielded cables.This kind of cable

is available from Advantech. Please contact your local sup-

plier for ordering information.

Analog Input

• Channels: 4 (simultaneous sampling, 50 Ωpseudo

differential conﬁgurable)

• Resolution: 24 bits (delta-sigma ADC)

• Max. Sampling Rate: 1 ~ 192 kS/s

• Input Coupling: AC/DC, selectable per channel

• Trigger Mode: Start, delay start, stop, delay stop

• Input Range: ±1 V, ±2 V, ±5 V, ±10 V

• Offset Error: < ±0.2 mV

• Gain Error:< ±0.02% of full-scale range

• Total Harmonic Distortion Plus Noise (THD+N): -95 dB

• IEPE Excitation: 2 mA

• Automatic Calibration: Ye s

Analog Output

• Channels: 2 (50 Ωpseudo differential)

• Resolution: 24 bits (delta-sigma DAC)

• Update Rate: 1 ~ 192 kS/s

• Output Coupling: DC

• Output Range: ±1 V, ±10 V

• Offset Error: < ±0.5 mV

• Gain Error: < ±0.03% of full-scale range

Declaration of ConformityPacking List

For more information about this or other Advantech

products, visit our website at

http://www.advantech.com

For technical support and customer service, visit our

support website at

http://support.advantech.com

This manual is for USB-5801.

Part No. 2041580101

Printed in China

Edition 2

May 2019

Specications

Overview

2 USB-5801 Startup Manual

• Total Harmonic Distortion Plus Noise (THD+N): -91 dB

• Trigger Mode: Start, delay start, stop, delay stop

• Automatic Calibration: Ye s

Tachometer Input

• Channels: 2

• Input Voltage: Logic 0: 3 V max.

Logic 1: 10 V min. (30 V max.)

• Input Frequency: 5 kHz max.

• Digital Filter: 16 μs ~ 131 ms

• Isolation Protection: 2,500 VDC

Digital Input

• Channels: 4

• Input Voltage: Logic 0: 3 V max.

Logic 1: 10 V min. (30 V max.)

• Opto-Isolator Response Time: 100 μs

• Digital Filter: 16 μs ~ 131 ms

• Isolation Protection: 2,500 VDC

Digital Output

• Channels: 4

• Load Voltage: 5 ~ 40 VDC

• Load Current: 350 mA/ch (sink)

• Opto-Isolator Response Time: 100 μs

• Isolation Protection: 2,500 VDC

General

• Interface: USB 3.0

• Data Transfer Rate: 5 Gbps

• Connectors:

6 x BNC (AI and AO)

2 x 10-pin, 3.81-mm terminal blocks (tachometer, trigger,

and DI/O)

2 x 3-pin, 3.81-mm terminal blocks (power)

1 x USB 3.0 type A (downstream port)

1 x USB 3.0 type B (upstream port)

• Dimensions:

168 x 120 x 40 mm (6.6 x 4.7 x 1.6 in)

• Operating Temperature: 0 ~ 60 °C (32 ~ 140 °F)

• Storage Temperature: -40 ~ 70 °C (-40 ~ 158 °F)

• Storage Humidity: 5 ~ 95% RH (non-condensing)

• Power Supply: External 10 ~ 30 VDC or USB bus power

• Power Consumption:

150 mA typ./200 mA max. @24 V external power

700 mA typ./860 mA max. @5 V bus power

Specications (Cont.)

We recommend installing the driver before installing the

USB-5801 module to guarantee problem-free installation.

The Advantech DAQNavi Device Drivers setup program

for the USB-5801 module can be downloaded from the

Advantech website (www.advantech.com). Follow the steps

outlined below to install the driver software.

1. Execute the USB-5801 driver package.

2. The driver installation program should be launched.

When the setup program is launched, a setup screen

will be displayed.

3. Click the “Next” button and wait for driver installation.

4. Click the “Finish” button to exit the setup program.

After the device drivers are installed, the USB-5801 module

can be installed in the computer. We recommend referring

to the user manual or related documentation for detailed in-

structions. Alternatively, follow the steps outlined below for

module installation.

1. Touch any metal surface of the computer to discharge

any static electricity that may be in your body.

2. Insert the USB module into the designated USB port.

Use caution when inserting the module to avoid damage

due to excessive force.

After the module is installed, the device can be conﬁgured

using the Advantech Navigator Program automatically in-

stalled during driver setup. Complete device installation pro-

cedures should include device setup, conﬁguration, and test-

ing. Information is provided in the following sections to guide

users through the device setup, conﬁguration, and testing.

Hardware Installation

Driver Installation

USB-5801 Startup Manual 3

Block Diagram

Connector, Switch, and LED Locations

4 USB-5801 Startup Manual

Switch Description

SW1

Board ID switch. Refer to the table below for board ID conﬁguration.

Board ID 1 2 3 4

↑ ↑ ↑ ↑

↑ ↑ ↑ ↓

↑ ↑ ↓ ↑

↑ ↑ ↓ ↓

↑ ↓ ↑ ↑

↑ ↓ ↑ ↓

↑ ↓ ↓ ↑

↑ ↓ ↓ ↓

↓ ↑ ↑ ↑

↓ ↑ ↑ ↓

↓ ↑ ↓ ↑

↓ ↑ ↓ ↓

↓ ↓ ↑ ↑

↓ ↓ ↑ ↓

↓ ↓ ↓ ↑

↓ ↓ ↓ ↓

Connector Description

CN1 USB upstream port (USB 3.0 type-B connector with screw). Connect this port to the host or the down-

stream port of the previous USB module.

CN2 USB downstream port (USB 3.0 type-A connector with screw). Connect this port to the upstream port of

the next USB module, if any.

Board ID Switch and Connectors

USB-5801 Startup Manual 5

Connector Pin Description

CN4

Center pin Positive terminal of analog input channel 0

Outer shield Negative terminal of analog input channel 0

CN5

Center pin Positive terminal of analog input channel 1

Outer shield Negative terminal of analog input channel 1

CN6

Center pin Positive terminal of analog input channel 2

Outer shield Negative terminal of analog input channel 2

CN7

Center pin Positive terminal of analog input channel 3

Outer shield Negative terminal of analog input channel 3

CN8

Center pin Positive terminal of analog output channel 0

Outer shield Negative terminal of analog output channel 0

CN9

Center pin Positive terminal of analog output channel 1

Outer shield Negative terminal of analog output channel 1

Connector Pin Description

CN10 & CN11

C<0…1>CLK Clock input for counter channel 0 and 1

C<0…1>SCK Sample clock input for counter channel 0 and 1

TRGIN Digital trigger input

TRGOUT Digital trigger output

I<0…3> Digital input channel 0 through 3

O<0…3> Digital output channel 0 through 3

EC Common point for digital input signals

PC Common point for digital output signals

GND Ground for digital signals

Connector Pin Name Description

CN12 &

CN13

+VS External 10 ~ 30 V

power supply

GND Power ground

Chassis ground

Note: CN12 and CN13 are used for power redundancy. External power can be supplied by either connector.

Pin Assignments

6 USB-5801 Startup Manual

LED State Description

LED2

Off Module is not powered on

Green Module is powered on using either USB bus power or external power

LED3

Off Initial state. Module has not been connected

Green Upstream port is connected. Module is functioning normally

Red Upstream port is not connected or is disconnected. Module function is halted

LED4

Off Downstream port is not connected

Blue Downstream port is connected

LED State Description

Near CN4

Off No sensor is connected to analog input channel 0 or the sensor wire is broken

Green Sensor is connected to analog input channel 0 and works normally

Red Sensor connected to analog input channel 0 is short circuited

Near CN5

Off No sensor is connected to analog input channel 1 or the sensor wire is broken

Green Sensor is connected to analog input channel 1 and works normally

Red Sensor connected to analog input channel 1 is short circuited

Near CN6

Off No sensor is connected to analog input channel 2 or the sensor wire is broken

Green Sensor is connected to analog input channel 2 and works normally

Red Sensor connected to analog input channel 2 is short circuited

Near CN7

Off No sensor is connected to analog input channel 3 or the sensor wire is broken

Green Sensor is connected to analog input channel 3 and works normally

Red Sensor connected to analog input channel 3 is short circuited

Note: LEDs near CN4 ~ CN7 function only when IEPE is enabled for the corresponding analog input channel.

LED Status Descriptions

Autres manuels pour USB-5801

Table des matières

Autres manuels Advantech Unité de contrôle

Advantech

Advantech ADAM-3750 3-Wire Series Manuel d'installation et d'exploitation

Advantech

Advantech B+B SmartWorx IE-iMcV-2xLIM Manuel utilisateur

Advantech

Advantech Adam 4000 Series Manuel utilisateur

Advantech

Advantech iDAQ-817 Manuel utilisateur

Advantech

Advantech EPD-130 Manuel utilisateur

Advantech

Advantech ADAM-6217 Manuel utilisateur

Advantech

Advantech MOS-2120-Z1101E Manuel utilisateur

Advantech

Advantech SOM-2569 Manuel utilisateur

Advantech

Advantech WISE-1510 Manuel utilisateur

Advantech

Advantech IPMI-1000 Manuel d'installation et d'exploitation

Advantech

Advantech ADAM-5240 Manuel utilisateur

Advantech

Advantech APAX-5202P Manuel utilisateur

Advantech

Advantech PCM-3526 Manuel d'installation et d'exploitation

Advantech

Advantech WISE-2211 Manuel d'installation et d'exploitation

Advantech

Advantech ADAM-2000 Series Manuel utilisateur

Advantech

Advantech MIO-6254 Manuel d'installation et d'exploitation

Advantech

Advantech PCM-23C1CF Manuel utilisateur

Advantech

Advantech WISE-1840 Manuel utilisateur

Advantech

Advantech MIC-75M20-00B Manuel d'installation et d'exploitation

Advantech

Advantech PCM-3612I Manuel d'installation et d'exploitation

Advantech

Advantech USB-4716 Manuel d'installation et d'exploitation

Advantech

Advantech PCM-3524 Manuel utilisateur

Advantech

Advantech Adam 4000 Series Manuel utilisateur

Advantech

Advantech SOM-6898 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur