Wilson Electronics 801102 Manuel utilisateur

AMPS

IN BUILDING

Bi-directional Amplier

#801102 (43dB Model)

#801103 (50dB Model)

#801104 (60dB Model)

FCC ID: PWO824WB56

IC: 4726A-824WB56

iDEN

IN BUILDING

Bi-directional Amplier

#804001 (43dB Model)

#804003 (50dB Model)

#804004 (60dB Model)

FCC ID: PWO806WB56

IC: 4726A-806WB56

Installation Guide

Wilson Electronics, Inc.

3301 E. Deseret Drive, St. George, Utah 84790

For additional technical support go to

www.wilsonelectronics.com

Phone: 1-866-294-1660 Fax: 1-435-656-2432

IN BUILDING

Wireless

The term “IC:” before the radio certification number only signifies

that Industry of Canada technical specifications were met.

1. PURPOSE OF THE AMPS/iDEN AMPLIFIER

The AMPS/iDEN Bi-directional Amplier improves RF coverage for areas in

which low signal strength or no signal is a problem.

2. PACKAGE CONTENTS

2.1 AMPS/iDEN Bi-directional Amplier

2.2 AC-to-DC (110 volt) Power Supply

3. HOW THE AMPS/iDEN AMPLIFIER FUNCTIONS

The signal is received by the outside antenna from the cell site. The signal is then

AMPLIFIED and transmitted to your phone through the inside antenna. When

the phone transmits, the signal is received by the inside antenna and then

AMPLIFIED and transmitted to the cell site through the outside antenna.

The information provided by Wilson Electronics, Inc. is believed to be complete and accurate.

However, no responsibility is assumed by Wilson Electronics, Inc. for any business or per-

sonal losses arising from its use, or for any infringements of patents or other rights of third

parties that may result from its use.

4. AMPLIFIER INSTALLATION (see illustration on 4-5)

4.1 Installing the Wilson Cellular Outside Antenna

4.1.1 Select a location on the roof using your AMPS/iDEN phone in test mode to

nd the best signal strength. (See leaet titled PHONE TEST MODES)

4.1.2 The Outside Antenna should be located in an area with at least a 3’ radius

clear of obstructions and other radiating elements.

NOTE: Mount the AMPLIFIER away from direct sunlight, excessive heat

and/or moisture. The amplifier needs proper ventilation.

DO NOT place the amplifier in an air-tight enclosure.

WARNING: The outside antenna used with this amplier must be xed-

mounted on an outdoor permanent structure with a separation of at least 20

feet from all persons during normal operation.

4.2 Installing The Amplier

WARNING: Connecting amplier directly to cell phone may damage phone.

4.2.1 Mount the AMPLIFIER on a wall or ceiling using #6 screws.

4.2.2 Connect the Outside Antenna to the AMPLIFIER side labeled “OUTSIDE

ANTENNA”.

4.2.3 Connect the Inside Antenna to the AMPLIFIER side labeled “INSIDE

ANTENNA”.

4.2.4 Verify that both the OUTSIDE and INSIDE antennas are connected be-

fore connecting the AC-DC power supply to the power outlet.

4.3 Installing The Wilson Cellular Inside Antenna

4.3.1 The Inside Antenna should be centered in the weak signal area. The

INSIDE ANTENNA should be at least 7’ from the ground.

WARNING: The inside antenna used with this amplier must be mounted

with a separation distance of at least 8 inches from all persons and must not be

co-located or operating in conjunction with any other antenna or amplier.

4.4 When covering large areas a splitter can be used to allow for more than one

inside antenna. Extension cables can also be used if the weak signal area is

located far from the location of the outside antenna.

NOTE: A minimum of 20’ coax extension is recommended for isolation

between antennas.



 



  

 











 

 

 

  

 

 

 

 

5. AMPLIFIER SPECIFICATIONS FOR AMPS 43dB, 50dB & 60dB MODELS

Part #: 801102 (43dB Model) & 801103 (50dB Model) & 801104 (60dB Model)

43dB 50dB 60dB

Frequency 824-849MHz Uplink 869-894MHz Downlink

Gain (up/down) (43dB/43dB) (50dB/50dB) (60dB/60dB)

Flatness (up/down) (+/- 4dB/+/-4dB) (+/- 4dB/+/-6dB) (+/- 4dB/+/-6dB)

Max RF (up/down) (+31.7dBm/+10dBm) (+31.7dBm/+10dBm) (+31.7dBm/+10dBm)

Noise Figure (down) (3dB nominal) (3dB nominal) (3dB nominal)

Isolation Uplink/Downlink More than 90dB

Power Consumption 13.8V, 1.5A

AMPLIFIER LAYOUT

KEEP A SEPARATION DISTANCE OF AT

LEAST 20ft HORIZONTAL AND 5ft VERTI-

CAL BETWEEN ANTENNAS

If using the Yagi Antenna, make sure the Yagi

is pointed AWAY from the inside antenna.



 



  

 











 

 

 

  

 

 

 

 

AMPLIFIER SPECIFICATIONS FOR iDEN 43dB, 50dB & 60dB MODELS

Part #: 804001 (43dB Model) & 804003 (50dB Model) & 804004 (60dB Model)

43dB 50dB 60dB

Frequency 806-821MHz Uplink 851-866MHz Downlink

Gain (up/down) (43dB/43dB) (50dB/50dB) (60dB/60dB)

Flatness (up/down) (+/- 4dB/+/-4dB) (+/- 4dB/+/-6dB) (+/- 4dB/+/-6dB)

Max RF (up/down) (+31.7dBm/+10dBm) (+31.7dBm/+10dBm) (+31.7dBm/+10dBm)

Noise Figure (down) (3dB nominal) (3dB nominal) (3dB nominal)

Isolation Uplink/Downlink More than 90dB

Power Consumption 13.8V, 1.5A

AMPS/iDEN AMPLIFIER PHYSICAL

SPECIFICATIONS

Connectors FME-Male 50 Ohms

Dimensions 5.5x4.3x1.4 (inch) or

14.0x10.8x3.5 (cm)

Weight 1.32 Pounds or 600G

6. OPTIONAL ACCESSORIES/ANTENNA OPTIONS

6.1 2-Way RF Splitter - allows for multiple inside antennas.

6.2 Coax Cable Extensions 50Ω (see chart on next page)

6.3 Antenna Options:

Inside Antenna Options Outside Antenna Option

301103 - Magnet Mount 301111 - Yagi

301106 - Stealth

301113 - Mini Magnet

6.4 N-Female To FME-Female Adapter - Adapts 9913 Coax to t the AMPS/

iDEN Bi-directional Amplier

6.5 Lightning Suppressor

WARNING: Lightning protection is recommended for all installations.

6.6 DC Power Cable

7. TECH SUPPORT

If you need further assistance with your installation:

1) Call us Toll-Free at 866-294-1660

2) E-mail tech support at [email protected]

3) Go to www.wilsonelectronics.com

Our Hours of Operation are: 8:00 AM – 4:30 PM (Mountain Time)

8. WARNINGS

WARNING: The outside antenna used with this amplier must be xed-mounted

on an outdoor permanent structure with a separation of at least 20 feet

from all persons during normal operation.

WARNING: The inside antenna used with this amplier must be mounted with a

separation distance of at least 8 inches from all persons and must not

be co-located or operating in conjunction with any other antenna or

amplier.

WARNING: Verify that both the Outside and Inside Antennas are connected before

plugging in the AC-DC power supply to the power outlet.

WARNING: Lightning protection is recommended for all installations.

951101 5’ Extension Cable RG 58

Low Loss Coax

(0.6 db loss)

951102 10’ Extension Cable RG 58

Low Loss Coax

(1.2 db loss)

951103 15’ Extension Cable RG 58

Low Loss Coax

(1.8 db loss)

951104 20’ Extension Cable RG 58

Low Loss Coax

(2.4 db loss) Used with the Yagi

Antenna - (N-Male to FME Female)

951108 20’ Extension Cable 9913

Ultra Low Loss Coax

Only use 9913 Low Loss Coax for

extensions 20’ or longer (0.8 db loss)

951105 30’ Extension Cable 9913

Ultra Low Loss Coax

(1.2 db loss)

951106 50’ Extension Cable 9913

Ultra Low Loss Coax

(2.0 db loss)

951107 100’ Extension 9913 Low

Loss Coax

(4.0 db loss)

951110 2’ Extension RG 58 Low

Loss Coax

(N-Male to FME Female)

Used with the Yagi antenna to help

nd the optimum signal strength (for

installation purposes only).

951113 2’ Extension 9913 Ultra

Low Loss Coax

(N-Male to N Male Ends)

(0.08 db loss) Jumper Coax - Can be

used to connect a splitter behind an

amplier.

EXTENSION CABLE CHART

RG 58 - FME connectors / 9913 - N connectors

Operation is subject to the following two conditions: (1) This device may not cause

interference, and (2) this device must accept any interference, including interference that

may cause undesired operation of this device.

 









 

    

  

   





 

 

    

  

   

 



For more options visit

www.wilsonelectronics.com

15 DAY

MONEY BACK

GUARANTEE

All Wilson products

have a 15 day

money back

guarantee with

Proof of Purchase

1 YEAR WARRANTY

The Wilson amplifier is warranted for one year against defects in workmanship

and/or materials and will be repaired or replaced, at the discretion of the manufac-

turer, to the original purchaser with dated proof of purchase or sales receipt.

If you have questions about your amplifier please call technical support

call 1-866-294-1660 or E-mail [email protected]

Most warranty cases can be handled by taking the amplifier and the re-

ceipt to the store where it was purchased. If inconvenient, the amplifier and a

copy of the receipt, may be sent to the factory, at purchasers expense, where

it may be repaired or replaced and returned shipping paid. Warranty does not

cover damages caused by abuse, misuse, and negligence.

ANTENNA OPTIONS

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Wilson Electronics Amplificateur

Wilson Electronics

Wilson Electronics 271220 Manuel utilisateur

Wilson Electronics

Wilson Electronics 271265 Instructions d'utilisation et d'entretien

Wilson Electronics

Wilson Electronics SIGNALBOOST MobilePro Manuel utilisateur

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 1300 Manuel utilisateur

Wilson Electronics

Wilson Electronics PRO 710i Manuel utilisateur

Wilson Electronics

Wilson Electronics 271247-50 Manuel utilisateur

Wilson Electronics

Wilson Electronics IoT 5-Band Manuel utilisateur

Wilson Electronics

Wilson Electronics U-Booster 2B5225 Manuel utilisateur

Wilson Electronics

Wilson Electronics SignalBoost DT Manuel utilisateur

Wilson Electronics

Wilson Electronics SIGNALBOOST C-Booster Manuel utilisateur

Wilson Electronics

Wilson Electronics 2B1401 Manuel utilisateur

Wilson Electronics

Wilson Electronics SignalBoost DT Manuel utilisateur

Wilson Electronics

Wilson Electronics iDEN Manuel utilisateur

Wilson Electronics

Wilson Electronics 801230 Manuel utilisateur

Wilson Electronics

Wilson Electronics 814001 Manuel utilisateur

Wilson Electronics

Wilson Electronics WilsonPro ENTERPRISE A8000 Manuel utilisateur

Wilson Electronics

Wilson Electronics 814001 Manuel utilisateur

Wilson Electronics

Wilson Electronics 801105 Manuel utilisateur

Wilson Electronics

Wilson Electronics 811101 Manuel utilisateur

Wilson Electronics

Wilson Electronics 271245 Manuel utilisateur

Wilson Electronics

Wilson Electronics BD800AM Manuel utilisateur

Wilson Electronics

Wilson Electronics SIGNALBOOST 811210 Manuel utilisateur

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 4300R Manuel utilisateur

Wilson Electronics

Wilson Electronics 801105 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur