Wilson Electronics 811101 Manuel utilisateur

Amplifier

Installation

ide

stallatio

stallat

Direct Connection

Ampliﬁers

Contents:

Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1

Before Getting Started / How it Works · · · · · · · · · · · · · · 3

Installing a Wilson Outside Antenna - In-Vehicle · · · · · · 4

Installing a Wilson Ampliﬁer - In-Vehicle · · · · · · · · · · · · 5

Installing a Wilson External Adapter - In-Vehicle · · · · · · 6

Installing a Wilson Outside Antenna - In-Building · · · · · 7

Installing a Wilson Ampliﬁer - In-Building · · · · · · · · · · · · 7

Installing a Wilson External Adapter - In-Building · · · · · 8

Powering Up a Wilson Ampliﬁer · · · · · · · · · · · · · · · · · · · 9

Warnings and Recommendations · · · · · · · · · · · · · · · · · 10

Ampliﬁer Speciﬁcations · · · · · · · · · · · · · · · · · Back Cover

Wilson

Electronics, Inc.

Warning: This manual contains

important safety and operating information.

Please read and follow the instructions

in this manual. Failure to do so could be

hazardous and result in damage to your

ampliﬁer.

30-Day Money-Back Guarantee

All Wilson Electronics products are protected by Wilson’s 30-day money-back

guarantee. If for any reason the performance of any product is not acceptable,

simply return the product directly to the reseller with a dated proof of purchase.

1-Year Warranty

Wilson Electronics ampliﬁers are warranted for one (1) year against defects in

workmanship and / or materials. Warranty cases may be resolved by returning the

product directly to the reseller with a dated proof of purchase.

Ampliﬁers may also be returned directly to the manufacturer at the consumer’s

expense, with a dated proof of purchase and a Returned Material Authorization

(RMA) number supplied by Wilson Electronics. Wilson shall, at its option, either

repair or replace the product. Wilson Electronics will pay for delivery of the repaired

or replaced product back to the original consumer.

This warranty does not apply to any ampliﬁers determined by Wilson Electronics

to have been subjected to misuse, abuse, neglect, or mishandling that alters or

damages physical or electronic properties.

RMA numbers may be obtained by phoning Technical Support at 866-294-1660.

The Manufacturer’s rated output power of this equipment is for single carrier operation.

Operation is subject to the following two conditions: (1) This device may not cause

interference, and (2) this device must accept any interference, including interference that

may cause undesired operation of this device.

Disclaimer: The information provided by Wilson Electronics, Inc. is believed to

be complete and accurate. However, no responsibility is assumed by Wilson

Electronics, Inc. for any business or personal losses arising from its use, or for

any infringements of patents or other rights of third parties that may result from

its use.

Installation Instructions for the Following Wilson Ampliﬁers

Direct Connection Single Band Ampliﬁer – Model # 811101

Contains 1900 MHz bypass to allow for antenna gain and 1575 MHz bypass to

allow for GPS reception.

FCC ID: PWO824D IC: 4726A-824D

Direct Connection Dual-Band Ampliﬁer – Model # 811201

Safe for use on all Cellular and PCS carriers.

FCC ID: PWO819D IC: 4726A-819D

Direct Connection Dual-Band GSM / TDMA Ampliﬁer – Model # 812201

Designed speciﬁcally for GSM / TDMAbands

FCC ID: PWO819D IC: 4726A-819D

Direct Connection iDEN Ampliﬁer – Model # 814001

Designed speciﬁcally for the iDEN 800 MHz band.

FCC ID: PWO806D IC: 4726A-806D

The term “IC” before the radio certiﬁcation number only signiﬁes that Industry

Canada technical speciﬁcations were met.

Antenna Options and Accessories

Mini

Magnet

Dual-Band Magnet

Mount

Dual-Band

NMO

Mount

Dual-Band

Marine

Antenna

Dual-Band

Trucker

Mount

Dual-Band

Ampliﬁer

Soft

Cases

Ampliﬁer

Hard Kit

Cases

13 dB 800 MHz Yagi Cellular Antenna

1900 MHz Yagi PCS Antenna

800 MHz Yagi

Cellular Antenna

Before Getting Started

This guide will help you properly install Wilson’s direct connection ampliﬁers in

both in-vehicle and in-building applications. It is important to read through all

of the installation steps for your particular application prior to installing

any equipment. Read through the instructions, visualize where all the

equipment will need to be installed and do a soft installation before mounting any

equipment. If you do not understand the instructions in full, seek professional

help, or contact Wilson Technical Support at 866-294-1660.

Inside this Package

• Direct connection ampliﬁer

• DC plug-in power supply with On/Off switch

• 6 ‘ extension cable

Additional Equipment

• Outside antenna for in-vehicle or in-building use (required)

(NOTE: speciﬁcally tuned iDEN antennas available)

• Cell phone-speciﬁc external antenna adapter (required)

• AC/DC power supply (optional – for in-building use)

How it Works

Wilson ampliﬁers are small, portable, bi-directional devices that deliver service

levels consistent with what would be expected in areas of high cell network

coverage. They amplify a weak or shadowed signal in mobile, marine and in-

building applications.

When using a Wilson ampliﬁer in conjunction with Wilson antennas, the outside

antenna will collect the cell tower signal and send it through the cable to the

ampliﬁer. Cell phones and cellular data cards (laptops) then communicate with

the improved signal. When a cell phone or cellular data card transmits, the

signal is ampliﬁed by the ampliﬁer and broadcast back to the cell tower through

the outside antenna.

Direct connection

ampliﬁer 6‘ extension

cable

DC plug-in power

supply Cable

wrench

The outside antenna must be installed

vertically. Signal performance will be

degraded if the antenna is not vertical.

The antenna cable may be run through

the door to the ampliﬁer.

The antenna cable is small enough

to easily tuck under the door seal or

plastic molding.

For a more professional-looking

installation, the antenna cable may

be run under the door seal. Carefully

pull down the door seal. Run the

cable through the seal and push the

seal back into place. This prevents

constant wear and tear on the cable as

the door opens and closes.

Optional Magnet-

Mount Antenna

Shown

Part #301103

Carefully

Pull Down

Door Seal

Run Cable

Under

Seal

Tuck Cable

Under Seal

Installing a Wilson Outside Antenna

To receive the best cell signal, select a location in the center of the vehicle’s roof

at least 12 inches away from any other antennas and free of obstructions.

Follow the speciﬁc antenna installation instructions included with the outside antenna

(sold separately).

In-Vehicle

Select a location to install the ampliﬁer

that is away from excessive heat,

direct sunlight, moisture and that has

proper ventilation.

Recommended installation locations

for in-vehicle are:

• Under the seat

• In the trunk

• Under the dash

Run the cable from the outside

antenna and attach it to the FME-Male

connector labeled “outside antenna” on

the ampliﬁer.

Installing a Wilson Ampliﬁer

Outside

Antenna

Ampliﬁer

DC Power

Supply

Cell Phone

Warning: Do not plug in the DC power

supply until the outside antenna and external

adapter cables are attached to the ampliﬁer.

In-Vehicle

Installing a Wilson External Adapter

An 18-inch external adapter is required to connect the cell phone or cellular data

card to the ampliﬁer. The external adapter is cell phone/data card-speciﬁc and

may be purchased through a local retailer.

Refer to Wilson’sAdapter Guide to

identify the right adapter for your

cell phone or cellular data card. The

adapter guide is available through a

local retailer or visit

www.wilsonelectronics.com.

The external adapter plugs into the included antenna extension cable and directly

into a socket on the cell phone or cellular data card as shown in Figure 1.

The external adapter and the included extension cable are long enough to reach

the ampliﬁer location. This allows for ease and convenience of use.

Run the extension cable from the external adapter and attach it to the FME-Male

connector labeled “cellular phone” on the ampliﬁer.

Sample

adapter

Figure 1

NOTE: Depending on your speciﬁc cell

phone, the adapter socket may be located

beneath a rubber plug.

In-Vehicle

Installing a Wilson Outside Antenna – In-Building

Select a location on the roof of the building to install the outside antenna that has

the most unobstructed line of sight to the cell tower.

Follow the speciﬁc antenna installation instructions included with the outside

antenna.

Lightning protection is recommended for all in-building installations. Take extreme

care to ensure neither you nor the antenna come in contact with any electrical

power lines.

AYagi antenna must be installed horizontally with the elements vertical and the

drip hole on the bottom. Ensure there are three feet of clearance in all directions

surrounding the antenna.

To obtain maximum performance, the antenna should point toward the cell tower.

Follow the instructions included with the outside antenna.

Cell Tower RF Signal

Yagi External Antenna

Warning: The outside antenna must

be installed on an outdoor permanent structure

with a separation of at least 20 feet from all

persons during normal operation.

Installing a Wilson Ampliﬁer

Select a location to install the ampliﬁer that is away from excessive heat, direct

sunlight, moisture and that has proper ventilation. Ensure the ampliﬁer is

installed within six feet of where the cell phone or cellular data card will be used

(to accommodate the six-foot adapter extension cable). Run the cable from

the outside antenna and attach it to the FME-Male connector labeled “outside

antenna” on the ampliﬁer. Connect the AC/DC power supply (sold separately) to

the power input labeled “DC 12 V IN” on the ampliﬁer.

Recommended installation locations for

in-building are:

• On a wall

• On the ceiling

• Near a power outlet

In-Building

Installing a Wilson External Adapter

An 18-inch external adapter is required to connect the cell phone or cellular data

card to the ampliﬁer. The external adapter is cell phone/data card-speciﬁc and

may be purchased through a local retailer.

Refer to Wilson’sAdapter Guide to

identify the right adapter for your

cell phone or cellular data card. The

adapter guide is available through a

local retailer or visit

www.wilsonelectronics.com.

The external adapter plugs into the included six-foot extension cable and directly

into a socket on the cell phone or cellular data card as shown in Figure 1 on

page 6. (NOTE: See the user’s manual for your speciﬁc phone or data card to

determine the socket location.)

Run the extension cable from the external adapter on the cell phone or cellular

data card and attach it to the FME-Male connector labeled “cellular phone” on the

ampliﬁer.

Extension Cable Chart

The following Wilson extension cables are available to help you customize your

installation for peak performance.

951101 5’ Extension Cable RG58U

Low Loss Coax 0.6 dB loss

951102 10’ Extension Cable RG58U

Low Loss Coax 1.2 dB loss

951103 15’ Extension Cable RG58U

Low Loss Coax 1.8 dB loss

951104 20’ Extension Cable RG58U

Low Loss Coax 2.4 dB loss, N-Male to FME-Female

951108 20’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax Only use 9913 Equivalent Low Loss Coax for

extensions 20’ or longer, 0.8 dB loss

951105 30’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax 1.2 dB loss

951106 50’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax 2.0 dB loss

951117 75’ Extension 9913 Equivalent

Ultra Low Loss Coax 3.0 dB loss

951107 100’ Extension 9913 Equivalent

Ultra Low Loss Coax 4.0 dB loss

951113 2’ Extension 9913 Equivalent Ultra Low

Loss Coax (N-Male to N-Male Ends) 0.08 dB loss, Jumper Coax - Can be used to

connect a splitter behind an ampliﬁer.

951110 2’ Extension RG58U Low

Loss Coax (N-Male to FME-Female)

Used with the Yagi antenna to help ﬁnd the

optimum signal strength

(for installation purposes only).

RG58U - FME connectors / 9913 - N connectors

Sample

adapter

In-Building

Powering up a Wilson Ampliﬁer

For in-vehicle, ﬁrst connect the power

cable to the ampliﬁer input marked

“DC 12 V IN” and then insert the large

end into a 12 V DC power socket or

cigarette lighter outlet.

The ampliﬁer may remain on all the

time; however, leaving the ampliﬁer on

in a vehicle when it is not running can

discharge the battery in a day or two.

A good option is to power the ampliﬁer

through the ignition switch so that

the ampliﬁer turns off and on with the

vehicle.

For in-building, ﬁrst connect the

optional AC/DC power supply to the

ampliﬁer input labeled “DC 12 V IN”

and then into a wall outlet.

Carefully insert the power cable.

In-vehicle 12-volt DC power supply (included)

Warning: Use only a Wilson power

supply. Use of a non-Wilson product could

damage your equipment.

Testing a Wilson Ampliﬁer

To test your ampliﬁer, go to a weak signal area where your cell phone registers

only 1-2 bars without the ampliﬁer turned on. Then, connect the ampliﬁer to the

phone and you should see a signal improvement of 2 or more bars. Note: many

phones take up to 20 seconds to reset the bar indicator.

Warning: Verify that both the outside

antenna and the adapter extension cable are

connected to the ampliﬁer before powering up

the ampliﬁer.

In-building AC/DC power supply (optional)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Wilson Electronics Amplificateur

Wilson Electronics

Wilson Electronics IoT 5-Band Manuel utilisateur

Wilson Electronics

Wilson Electronics 271220 Manuel utilisateur

Wilson Electronics

Wilson Electronics 271245 Manuel utilisateur

Wilson Electronics

Wilson Electronics SignalBoost Manuel utilisateur

Wilson Electronics

Wilson Electronics SIGNALBOOST C-Booster Manuel utilisateur

Wilson Electronics

Wilson Electronics SIGNALBOOST U-Booster 2B5225 Manuel utilisateur

Wilson Electronics

Wilson Electronics 2B1401 Manuel utilisateur

Wilson Electronics

Wilson Electronics BD800AM-M Manuel utilisateur

Wilson Electronics

Wilson Electronics 271247-50 Manuel utilisateur

Wilson Electronics

Wilson Electronics 814001 Manuel utilisateur

Wilson Electronics

Wilson Electronics WilsonPro ENTERPRISE A8000 Manuel utilisateur

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 1300 Manuel utilisateur

Wilson Electronics

Wilson Electronics PRO 710i Manuel utilisateur

Wilson Electronics

Wilson Electronics 271265 Instructions d'utilisation et d'entretien

Wilson Electronics

Wilson Electronics SIGNALBOOST 811210 Manuel utilisateur

Wilson Electronics

Wilson Electronics Smart Technology 801201-A Manuel utilisateur

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 4300 Manuel utilisateur

Wilson Electronics

Wilson Electronics BD800AM Manuel utilisateur

Wilson Electronics

Wilson Electronics 801102 Manuel utilisateur

Wilson Electronics

Wilson Electronics 801306 Manuel utilisateur

Wilson Electronics

Wilson Electronics 271247-75 Manuel utilisateur

Wilson Electronics

Wilson Electronics iDEN Manuel utilisateur

Wilson Electronics

Wilson Electronics PRO 710i Manuel utilisateur

Wilson Electronics

Wilson Electronics 271245 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur