Wilson Electronics 801306 Manuel utilisateur

Wilson Electronics, Inc.

3301 E. Deseret Drive, St. George, Utah 84790

For additional technical support visit

www.wilsonelectronics.com

Phone: 1-866-294-1660 Fax: 1-435-656-2432

IN-BUILDING

Wireless

The term “IC:” before the radio certification number signifies

that Industry of Canada technical specifications were met.

PCS Smart Technology™ Amplifier

Installation Guide

In-Building

Wireless PCS

Smart TechnologyTM Amplier

PART # 801306

1850-1990 MHz

FCC ID: PWO8013SB

IC: 4726A-8013SB

1. PURPOSE OF THE AMPLIFIER

The PCS Smart TechnologyTM Amplier improves RF coverage for areas in which low signal

strength is a concern.

2. PACKAGE CONTENTS

2.1 Amplier

2.2 AC/DC 110 volt Power Supply

3. HOW THE AMPLIFIER FUNCTIONS

The signal is received by the outside antenna from the cell site. The signal is then

AMPLIFIED and transmitted to your phone through the inside antenna. When the phone

transmits, the signal is received by the inside antenna and then AMPLIFIED and transmitted

to the cell site through the outside antenna.

4. AMPLIFIER INSTALLATION (see illustration on pg. 4 & 5)

4.1 Installing the Wilson Cellular Outside Antenna

WARNING: The outside antenna used with this amplier must be xed-mounted on

an outdoor permanent structure with a separation of at least 20 feet from all persons

during normal operation.

4.1.1 Select a location on the roof using your phone in test mode to nd the best signal

strength. (See leaet titled PHONE TEST MODES)

4.1.2 The outside antenna should be located in an area with at least a 3 foot radius clear of

obstructions and other radiating elements.

4.2 Installing The Amplier

WARNING: Connecting amplier directly to cell phone may damage phone.

WARNING: Connect both antennas before connecting power to the amplier.

4.2.1 Mount the AMPLIFIER on a wall or ceiling using #6 screws.

NOTE: Mount the AMPLIFIER away from direct sunlight, excessive heat and/or

moisture. The amplifier needs proper ventilation. DO NOT place the amplifier

in an air-tight enclosure.

4.2.2 Connect outside antenna to the amplier side labeled “OUTSIDE ANTENNA”.

4.2.3 Connect inside antenna to the amplier side labeled “INSIDE ANTENNA”.

4.2.4 Verify that both the outside and inside antennas are connected before connecting

the AC-DC power supply to the power outlet.

4.4 Installing The Wilson Cellular Inside Antenna

4.4.1 See antenna packaging for model specic instructions.

4.4.2 The inside antenna should be centered in the weak signal area. The inside antenna

should be at least 7 feet from the oor.

FCC Separation Warning

WARNING: The inside antenna used with this amplier must have a separation

distance from all persons that is at least:

9 inches for the 2.5 dBi Dome antenna.

14 inches for the 7 dBi Panel antenna.

The amplier must not be co-located or operating in conjunction with any other

antenna or amplier.

4.5 When covering multiple areas a 1900 MHz splitter can be used to allow for more than one

inside antenna. Extension cables can also be used if the weak signal area is located far from the

location of the outside antenna. For coax runs more than 20 feet use 9913 or equivalent coax.

NOTE: For Maximum gain (60 dB), keep a separation distance of at least 50 feet

between the outside and inside antennas. Closer spacings may be used,

but may cause the amplier to automatically reduce its gain.

NOTE: When using a Yagi antenna make sure the Yagi is pointed away from the

inside antenna.

ALL LIGHTS GREEN = 60 dB GAIN

LIGHT D OFF = 2 dB REDUCTION

LIGHT D & C OFF = 10 dB REDUCTION

LIGHT D, C & B OFF = 20 dB REDUCTION

LIGHT A RED = 40 dB REDUCTION

4.3 Indicator Lights

AC / DC

Power Supply

Amplifier

Inside Antenna to

Amplifier Connection

Cell

Site

Supports

Multiple

Users

Outside Antenna

1900 MHz Yagi Antenna Shown

Outside Antenna to

Amplifier Connection

Inside Antenna

Optional Dome

Antenna Shown

If using a Yagi Antenna,

Make sure the Yagi is not pointed

toward the inside antenna.

AMPLIFIER PHYSICAL

SPECIFICATIONS

Connectors N-Female 50 ohms

Dimensions 4.5 x 3.5 x 1.25 inches

11.4 x 8.9 x 3.2 (cm)

Weight 1.5 lbs / 0.7 kg

For maximum gain, keep a separation

distance of at least 50 feet between the

outside and inside antennas.

AC / DC

Power Supply

Amplifier

Inside Antenna to

Amplifier Connection

Cell

Site

Supports

Multiple

Users

Outside Antenna

1900 MHz Yagi Antenna Shown

Outside Antenna to

Amplifier Connection

Inside Antenna

Optional Dome

Antenna Shown

AMPLIFIER LAYOUT

DIAGRAM

5. AMPLIFIER SPECIFICATIONS

Part Number 801306

Gain 60 dB

Frequency PCS

1850-1910 MHz / 1930-1990 MHz

Linear Output Power 30 dBm

Max Output Power 3 watts

Max RF (up/down) +30 dBm / +30 dBm

Noise Figure (typical) 4 dB

Flatness (up/down) ± 4 dB

Isolation > 90 dB

Power Requirements 120 V AC 3 A Max

Connectors N-Female

Dimensions 4.5 x 3.5 x 1.25 (inch)

11.43 x 8.9 x 3.2 (cm)

Weight 1.5 lbs / 0.7 kg

6. OPTIONAL ACCESSORIES/ANTENNA OPTIONS

WARNING: Lightning protection is recommended for all installations.

6.1 3dB Dual-Band Splitter Part # 859911

6.2 Coax Cable Extensions 50Ω (see chart on next page)

6.3 Antenna Options:

Inside Antenna Options Outside Antenna Option

301103 - Magnet Mount 5 dBi 301124 - Yagi 13 dBi

301106 - Low Prole 2.2 dBi

301113 - Mini Magnet 2.12 dBi

301121 - Dome 2.5 dBi

301122 - Panel 7 dBi

301123 - Dual Polarity Dome, Unity

6.4 N-Male to FME-Male adapter Part # 971113

6.5 Lightning Surge Protection Part # 859902

7. TECH SUPPORT

If you need further assistance with your installation:

1) Call Toll-Free 866-294-1660 8:00 AM – 4:30 PM (Mountain Time)

2) E-mail tech support at [email protected]

3) Visit www.wilsonelectronics.com

8. WARNINGS

WARNING: The outside antenna used with this amplier must be xed-mounted on an out-

door permanent structure with a separation of at least 20 feet from all persons

during normal operation.

WARNING: The inside antenna used with this amplier must have a separation distance

from all persons that is at least:

9 inches for the 2.5 dBi Dome antenna.

14 inches for the 7 dBi Panel antenna.

The amplier must not be co-located or operating in conjunction with any

other antenna or amplier.

WARNING: Verify that both the Outside and Inside Antennas are connected before plug-

ging in the AC/DC power supply to the power outlet.

WARNING: Lightning protection is recommended for all installations.

Lightning protection is required for warranty validation.

The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no respon-

sibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from its use, or for any

infringements of patents or other rights of third parties that may result from its use.

951110 2’ Extension Cable RG58U

Low Loss Coax

N-Male to FME-Female

Used with the Yagi antenna to help nd the

optimum signal strength (for installation purposes

only).

951101 5’ Extension Cable RG58U

Low Loss Coax

0.6 dB loss

951102 10’ Extension Cable RG58U

Low Loss Coax

1.2 dB loss

951103 15’ Extension Cable RG58U

Low Loss Coax

1.8 dB loss

951104 20’ Extension Cable RG58U

Low Loss Coax

2.4 dB loss, N-Male to FME-Female

951113 2’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax

0.08 dB loss, Jumper Coax - Can be used to con-

nect a splitter behind an amplier.

951108 20’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax

Only use 9913 Equivalent Low Loss Coax for

extensions 20 feet or longer, 0.8 dB loss

951105 30’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax

1.2 dB loss

951106 50’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax

2.0 dB loss

951117 75’ Extension Cable 9913 Equivalent

Ultra Low Loss Coax

3.0 dB loss

951107 100’ Extension Cable 9913 Equivalent

Low Loss Coax

4.0 dB loss

EXTENSION CABLE CHART

RG58U - FME connectors / 9913 Equivalent - N connectors

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device

must accept any interference, including interference that may cause undesired operation of this device.

The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when mul-

tiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is

re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power

or gain reduction and not by an attenuator at the output of the device.

Trucker 3/8"

Mount

Mini

Magnet

Mount

Low

Profile

1900 MHz

Yagi

Dome Dual Polarity

Dome

Panel

Optional Accessories

Coax Cable Extension

Ultra Low Loss Coax

Lightning Suppressor

FME Male to

N-Male

15 DAY

MONEY BACK

GUARANTEE

All Wilson products

have a 15 day

money back

guarantee with

Proof of Purchase

1 YEAR WARRANTY

The Wilson amplifier is warranted for one year against defects in workmanship

and/or materials and will be repaired or replaced, at the discretion of the manufac-

turer, to the original purchaser with dated proof of purchase or sales receipt.

If any questions arise about an amplifier please call technical support toll-

free 1-866-294-1660 or E-mail [email protected]

Most warranty cases may be handled by taking the amplifier and the re-

ceipt to the store where it was purchased. If inconvenient, the amplifier and a

copy of the receipt, may be sent to the factory, at purchasers expense. It will

be repaired or replaced and returned shipping paid. Warranty does not cover

damages caused by abuse, misuse, and negligence.

801306_006 / 04.06.06

Table des matières

Autres manuels Wilson Electronics Amplificateur

Wilson Electronics

Wilson Electronics 271265 Instructions d'utilisation et d'entretien

Wilson Electronics

Wilson Electronics 271245 Manuel utilisateur

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 1300 Manuel utilisateur

Wilson Electronics

Wilson Electronics 271245 Manuel utilisateur

Wilson Electronics

Wilson Electronics PRO 710i Manuel utilisateur

Wilson Electronics

Wilson Electronics WILSONPRO PRO 140i Manuel utilisateur

Wilson Electronics

Wilson Electronics PRO 710i Manuel utilisateur

Wilson Electronics

Wilson Electronics SignalBoost DT Manuel utilisateur

Wilson Electronics

Wilson Electronics BD800AM Manuel utilisateur

Wilson Electronics

Wilson Electronics 271247-50 Manuel utilisateur

Wilson Electronics

Wilson Electronics 801105 Manuel utilisateur

Wilson Electronics

Wilson Electronics SignalBoost DT Manuel utilisateur

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 4300 Manuel utilisateur

Wilson Electronics

Wilson Electronics SIGNALBOOST 811210 Manuel utilisateur

Wilson Electronics

Wilson Electronics 271220 Manuel utilisateur

Wilson Electronics

Wilson Electronics 2B1401 Manuel utilisateur

Wilson Electronics

Wilson Electronics 271247-75 Manuel utilisateur

Wilson Electronics

Wilson Electronics 801230 Manuel utilisateur

Wilson Electronics

Wilson Electronics 801105 Manuel utilisateur

Wilson Electronics

Wilson Electronics Smart Technology 801201-A Manuel utilisateur

Wilson Electronics

Wilson Electronics 811101 Manuel utilisateur

Wilson Electronics

Wilson Electronics IoT 5-Band Manuel utilisateur

Wilson Electronics

Wilson Electronics 814001 Manuel utilisateur

Wilson Electronics

Wilson Electronics SignalBoost Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur