Unitronics Jazz JZ10-11-R16L Manuel utilisateur
Unitronics 1
Jazz™ OPLC ™ Micro-OPLC Installation Guide
JZ10-11-R16L
6 Digital, 2 Analog/Digital, 2 Analog Inputs, 6 Relay Outputs
Before using this product, the user must read and understand this document.
For additional information regarding this product, refer to the user guide and technical specifications.
All examples and diagrams are intended to aid understanding, and do not guarantee operation.
Unitronics accepts no responsibility for actual use of this product based on these examples.
Please dispose of this product according to local and national standards and regulations.
Only qualified service personnel should open this device or carry out repairs.
Failure to comply with appropriate safety guidelines can cause severe injury or property damage.
Do not attempt to use this device with parameters that exceed permissible levels.
To avoid damaging the system, do not connect/disconnect the device when power is on.
Environmental Considerations
Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,
moisture or rain, excessive heat, regular impact shocks or excessive vibration.
Ventilation: 10mm space required between the OPLCs’ top/bottom edges & enclosure walls.
Do not place in water or let water leak onto the unit.
Do not allow debris to fall inside the unit during installation.
Mounting
Dimensions
85.7mm(3.374")
113.7 mm (4.476")
13.2 mm (0.52")
16.8 mm (0.661")
46.6 mm (1.835")
4 mm (0.157")
7.5 mm (0.295")
12 mm (0.472")
147.5 mm (5.807")
117 mm (4.606")
Add-on modules
Take into account that installing an add-on module requires sufficient clearance space.
During installation After installation
72 mm (2.835")
27.5 mm
(1.083")
38mm
(1.496")
35.8mm
(1.409")
9/12
2 Unitronics
DIN-rail mounting
Snap PLC onto the DIN rail
Panel mounting
Cut-out: 117 x 89mm (WxH)
4.606”x 3.504”
35 mm
(1.378")
53 mm
(2.087")
..
Gasket
Panel
5mm (max)
0.197" (max)
Wiring
Note: All diagrams are based on the rear view of the OPLC.
Do not touch live wires.
Install an external circuit breaker. Guard against short-circuiting in external wiring.
Use appropriate circuit protection devices.
Unused pins should not be connected. Ignoring this directive may damage the device.
Double-check all wiring before turning on the power supply.
To avoid damaging the wire, do not exceed a maximum torque of 0.5 N·m (5 kgf·cm).
Do not use tin, solder, or any substance on stripped wire that might cause the wire strand to break.
Install at maximum distance from high-voltage cables and power equipment.
Use crimp terminals for wiring; use 26-12 AWG wire (0.13 mm
2
–3.31 mm
2
).
1. Strip the wire to a length of 7±0.5mm (0.250-0.300 inches).
2. Unscrew the terminal to its widest position before inserting a wire.
3. Insert the wire completely into the terminal to ensure a proper connection.
4. Tighten enough to keep the wire from pulling free.
Input or output cables should not be run through the same multi-core cable or share the same wire.
Allow for voltage drop and noise interference with input lines used over an extended distance. Use
wire that is properly sized for the load.
I
nputs
This model comprises a total of 10 inputs in 3 groups.
1. I0 to I5 are digital inputs. They may be wired, in a group, as either npn or pnp.
2. I6 and I7 may be wired as either digital or analog inputs. These may be wired as either:
npn digital inputs
pnp digital inputs
analog (voltage) inputs
In addition, 1 input may be wired as a pnp input, while the other is wired as an analog input.
Note that if 1 input is wired as an npn input, the other may not be wired as an analog input.
3. AN0 and AN1 are analog (voltage) inputs.
JZ10-11-R16L, 9/12
Unitronics 3
I/O Configuration
Digital Inputs, Controller’s Power Supply
Note: The inputs are arranged in two groups. You can wire one group as npn and the other as
pnp,or wire both groups as npn, or as pnp. In either case, the npn/pnp pins must be connected.
Input wiring (I0-I5), npn (sink) Input wiring (I0-I5), pnp (source)
Input wiring (I6-I7), npn (sink) Input wiring (I6-I7), pnp (source)
Digital Outputs
Output wiring
9/12
Increasing contact life span
To increase the life span of your contacts and protect the unit from potential damage by reverse-
EMF, connect:
A clamping diode in parallel with each inductive DC load
An RC snubber circuit in parallel with each inductive AC load
Analog inputs
Note: Shields should be connected at the signal source.
Analog Input wiring, current
2 or 3-wire, AN0 and AN1 4-wire, AN0 and AN1
Analog Input wiring, voltage
Note: If either I6 or I7 is wired as an npn digital input, the remaining input may not be wired as an
analog input.
JZ10-11-R16/V, AN2 and AN3 JZ10-11-R16V, AN0 and AN1
Samara
tel. +7 846 273 95 85
Yekaterinburg
tel. +7 343 287 19 19
yekat[email protected]
St. Petersburg
tel. +7 812 327 3752
Moscow
tel. +7 495 641 1616
Helsinki
tel. +358 9 540 4940
automation@klinkmann.
Vilnius
tel. +370 5 215 1646
Riga
tel. +371 6738 1617
Мinsk
tel. +375 17 200 0876
Tallinn
tel. +372 668 4500
Кiev
tel. +38 044 495 33 40
Table des matières
Autres manuels Unitronics Contrôleurs
Unitronics
Unitronics US5-B5-RA28 Manuel utilisateur
Unitronics
Unitronics Vision OPLC V130-J-TR20 Manuel utilisateur
Unitronics
Unitronics Jazz OPLC JZ20-T40 Manuel utilisateur
Unitronics
Unitronics Vision OPLC V350-35-TR20 Manuel utilisateur
Unitronics
Unitronics UniStream US5-B5-B1 Manuel utilisateur
Unitronics
Unitronics Jazz JZ20-UA24 Manuel utilisateur
Unitronics
Unitronics Vision OPLC V1040-T20B Manuel utilisateur
Unitronics
Unitronics Vision OPLC V570-57-C30B Manuel utilisateur
Unitronics
Unitronics Vision V130-33-T2 Manuel utilisateur
Unitronics
Unitronics Vision V130-J-TA24 Manuel utilisateur
Unitronics
Unitronics UniStream Manuel utilisateur
Unitronics
Unitronics UniStream USC-C3-R20 Manuel utilisateur
Unitronics
Unitronics Vision OPLC V1040-T20B Manuel utilisateur
Unitronics
Unitronics Vision OPLC V130-33-T38 Manuel utilisateur
Unitronics
Unitronics Vision120 Manuel utilisateur
Unitronics
Unitronics Vision V120 Manuel utilisateur
Unitronics
Unitronics US5-B10-RA28 Manuel utilisateur
Unitronics
Unitronics Samba OPLC Series Manuel utilisateur
Unitronics
Unitronics Vision OPLC V130-33-B1 Manuel utilisateur
Unitronics
Unitronics V280 Manuel utilisateur
