TPI 1008 Manuel utilisateur

Test Products International, Inc.

9615 SW Allen Blvd., Ste. 104

Beaverton, OR 97005

Tel: 503-520-9197 Fax: 503-520-1225

www.tpi-thevalueleader.com

Test Products International, Ltd.

342 Bronte Road South, Unit #9

Milton Ontario Canada L9T5B7

Tel: 905-693-8558 Fax: 905-693-0888

1008

Rev. 2.x Meters

Indoor Air Quality Meter

The Value LeaderTM

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Contents

1. Introduction

2. General Overview

3. Familiarization

3.1 Front View

3.2 Soft Keys

3.3 Back View

4. Operation

4.1 Turning On & Off / Performing a Test / Main Display

4.2 Selecting Temperature Units

4.3 Min / Max Mode

4.4 Activating the Backlight

4.5 Setting CO2 Alarm Level

5. Data Logging

6. Retrieving Logged Data

7. Technical Specifications

8. Maintenance

8.1 Battery Replacement

8.2 Service

9. Technical Information

10. Error Codes & Troubleshooting

Notes:

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Notes:

1. Introduction

Thank you for purchasing TPI brand products. The TPI 1008 Indoor Air

Quality (IAQ) Meter is a state of the art, easy to use tester designed to

provide you with the necessary measurements to monitor and make

adjustments to air handling devices. The instrument is ruggedly con-

structed and comes with a 3 Year unit and 2 Year sensor Guarantee.

2. General Overview

The 1008 IAQ meter uses state of the art sensors to measure carbon

dioxide (CO2), and temperature. The CO2 sensor in your meter will

need to be replaced periodically and calibration is recommended once

every year.

You should keep battery power applied to your sensors at all times.

The following guidelines will help prevent damage to your sensors:

Always store your unit in a place where the temperature does not get

down to or below freezing.

Always maintain battery power to the sensors. When the batteries get

low replace them as soon as possible.

Never allow foreign objects or material to enter the sensor holes, dam-

age to the sensor may result.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

General Overview (Continued)

This manual will guide you through the functions of the TPI 1008

which will give you many years of reliable service.

Your TPI 1008 Indoor Air Quality meter comes complete with the

following standard accessories:

• TPI 1008 Instrument

• Protective Rubber Boot (A800)

• Soft Carrying Case (A921)

• USB Cable & Software (A803)

• Instruction Manual

Your TPI 1008 Indoor Air Quality meter has the following optional

accessories available:

• Power adapter / Battery eliminator (A804)

• Magnetic strap kit to hang meter (A127)

• Boot hook to hang meter (A103)

• Replacement Software only (A802)

• Replacement USB cable only (A801)

( ) Denotes part number

Notes:

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

10. Error Codes & Troubleshooting

CO2 Sensor Error

If the CO2 sensor fails to initialize or is faulty the

1008 will display an error code. Try turning the 1008

off and on again. If it displays the error code again

the 1008 is in need of service. Please return your

instrument to TPI. See section 9.2 for instructions on

returning your meter.

Temperature Sensor Error

If the temperature sensor fails to initialize or is faulty

the 1008 will display an error code. Try turning the

1008 off and on again. If it displays the error code

again the 1008 is in need of service. Please return

your instrument to TPI. See section 9.2 for instruc-

tions on returning your meter.

3. Familiarization

3.1 Front View

Sensor Locations: Places where the CO and Temperature sensors

are located and protected.

Display : Large 2 Parameter Backlit LCD Display.

Protective Rubber Boot Provides protection to meter housing and sensors.

Keypad Selects all available functions

USB Port Location for connection of USB cable for PC com

munication.

Power Adapter Socket Location to connect power adapter.

Display

Keypad

CO2 &

Temperature

Sensor Location

USB Port Power Adapter

Socket

Protective

Rubber Boot

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

3.2 Soft Keys

On / Off key - Used to turn the IAQ meter on or off. Press to turn

on, press and hold to turn off.

Up Arrow key - Used to select and change parameters.

Down Arrow key - Used to select and change parameters.

Mode key - Used to switch between Celsius and Fahrenheit units

of display and to enter CO2 alarm level input mode. Press to

switch between Celsius and Fahrenheit units. Press and hold to

enter and exit CO2 alarm level mode.

Backlight key - Used to turn the display backlight on and off.

Min / Max key - Used to activate and cycle through minimum,

maximum, and average display modes. Press to activate Min/Max

mode, press repeatedly to cycle through min, max, and avg dis-

plays. Press and hold to deactivate Min/Max mode.

Log key - Used activate and deactivate data logging.

RCL Key - Used to recall (display) logged data.

9. Technical Information

Recommended Levels by Agency

Parameter IDPH1ASHRAE2OSHA PEL3ACGIH TLV4

Humidity 20% - 60% 30% - 60% N/A N/A

Temperature 68 - 75 (winter)

73 - 79 (summer) 68 - 75 (winter)

73 - 79 (summer) N/A N/A

Carbon Dioxide 1,000ppm

(<800ppm preferred) 1,000ppm 5,000ppm 5,000ppm

Carbon Monoxide 9ppm 9ppm 50ppm 25ppm

N/A-Not Applicable or Not Established

1Illinois Department of Public Health (2009)

2American Society of Heating, Refrigerating and Air Conditioning Engineers

3Occupational Safety and Health Administration Permissible Exposure Limit -- this level

is a time-weighted average and is an enforceable standard that must not be exceeded

during any eight-hour work shift of a 40-hour work week.

4American Conference of Governmental Industrial Hygienist Threshold Limit Value -- this

level is a recommended time-weighted average upper limit exposure concentration for a

normal eight to 10-hour workday and a 40-hour work week.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

8. Maintenance

It is recommended that the instrument be calibrated every 12 months.

Please consult Test Products International for further details (800) 368-5719.

8.1 Battery Replacement

When the batteries become low they will require replacement.

1. Turn the meter over so the back is facing you.

2. Loosen the screw holding down the battery cover located under the tilt

stand.

3. Lift the tilt stand up and remove the battery cover.

4. Replace the batteries (3 x AA Alkaline) and install the cover and tighten the

screw.

8.2 Service

To obtain warranty and non-warranty performance or maintenance on your

analyzer: - Include with the product your name, address, phone number, writ-

ten description of the problem and proof of purchase date. Carefully package

and return to:

TPI / Attn. Repair

9615 SW Allen Blvd. Suite 104

Beaverton, OR 97005

3.3 Back View

Tilt Stand

Battery Cover Screw

Hanger Hole

Hanger Hole: Use to hang instrument for hands free operation. Can

be used with A127 magnetic strap kit or A103 hook.

Tilt Stand: Use to stand instrument on a table.

Batter Cover Loosen this screw and open cover to access batteries.

Screw:

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

4. Operation

4.1 Turning On & Off / Performing a Test / Main Display

Enter the area to be tested, the measured values will be displayed.

Carbon dioxide (CO2) in parts per million (ppm) is displayed at the top and

Temperature in °F or °C (selectable)is displayed at the bottom of the main

display.

The battery indicator is located at the left center of the display. When the bat-

teries become low they must be replaced to maintain proper operation.

The 1008 has a CO2 alarm. If the CO2 level measured is at or above the

set alarm level the 1008 will beep and the display will flash red as a

warning. This alarm point is adjustable. Additional functions can be acti-

vated during testing. Please see next sections.

Carbon dioxide (CO2)

Temperature

Battery indicator

Press the key and the 1008 will begin a 30 second countdown. During

this time the 1008 performs a self diagnostic. Once the countdown ends the

1008 will display CO2 and Temperature.

To turn the 1008 off, press and hold the key down until the 1008 turns off.

7. Technical Specifications

Function Range Accuracy

CO2 0 to 5000ppm 50°F~104°F: ±3% of rdg+75ppm

<50°F, >104°F: ±5% of rdg+75ppm

Temperature -5°F to 140°F ±2°F

-20°C to 60°C ±1°C

Data Logging: Up to 50 samples 1 minute to 60 minutes in 1, 2, 3, 5, 10, 20, 30,

40, 50, 60 minute intervals

Display Type: 2 line with annunciators and backlight

CO2 Alarm: Audible and visual, selectable level (factory default off)

Operating Temperature & Humidity

CO and CO2: 14°F to 122°F (-10°C to 50°C)

All Other Function: -4°F to 140°F (-20°C to 60°C)

Humidity 15 ~ 95% non-condensing

Storage Temperature: -4°F to 140°F (-20°C to 60°C)

Power supply

3 AA battery( 4.5V)

AC/DC adapter 5Vout (Center positive)

Battery Life: 40 hours typical without backlight

Output: Serial output via USB connection

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

6. Retrieving Logged Data

Logged data can be displayed on the 1008 display or sent to a PC by using the

USB cable and software included. The PC software also provides the capability of

real time monitoring from a PC.

Recalling and Displaying Logged Data

Retrieving Logged Data via PC

To retrieve logged data the USB cable and PC software (both supplied) must be

used.

Install the PC software on your PC and open it.

Connect the 1008 to the PC using the USB cable.

Run the software and select 1008 when prompted. Click on the connect to PC

button in the software window.

The software can be used to retrieve logged data and for real time monitoring.

COM port setting is:

Baud rate: 19200

Parity: None

Data Bits: 8

Stop Bit: 1

1) Press the key, “LOG 01” and the logged CO2 and temperature reading

will alternately flash. Press the to cycle through all of the logged

data.

2) To deactivate recall mode and return to normal operation, press the

key.

4.2 Selecting Temperature Units

4.3 Min / Max Mode

4.4 Activating the Backlight

Pressing the key activates Min/Max mode and “Max Min” will be displayed.

In this mode the 1008 will keep track of the minimum, maximum, and average

CO2 and Temperature being measured. When “Min Max” is displayed the 1008

will display the real time reading.

Pressing the key switches the temperature display between °F and °C.

To deactivate Min/Max mode and return to normal operation, Press and hold the

key until the 1008 beeps.

Pressing the key turns the display backlight on and off. Power

consumption is much higher when the backlight is activated. The backlight

will automatically turn off 30 seconds after it is activated. To conserve bat-

tery life the backlight should only be used when necessary.

Pressing the key will cause the 1008 to display “MAX”. This indicates the

Maximum CO2 and Temperature measured is displayed.

Press the key again and the 1008 will display “MIN”. This indicates the

Minimum CO2 and Temperature measured is displayed.

Press the key again and the 1008 will display “AVG”. This indicates the

Average CO2 and Temperature measured is displayed.

Pressing the key will cause the 1008 to display “MAX MIN”. This indicates

the real time reading is displayed and the Min/Max mode is still active. The steps

above can be repeated to cycle through the Min, Max, and Avg displays.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

The 1008 is equipped with an audible and visual alarm for carbon dioxide. The

alarm level is factory set to off. When CO2 above the alarm level is measured, the

1008 will beep and the display will flash red.

The alarm level is adjustable and can be set from 1100ppm to 5000ppm in

100ppm increments.

Using the Arrow keys set the alarm point to the desired level. The

keys adjust the alarm level from “Off” to 5000ppm in 100ppm increments.

Once the desired alarm point is set, press and hold the key to return to

normal operation.

1) With the 1008 turned on, press and hold down the

CO2 alarm level in ppm

4.5 Setting CO2 Alarm Level

key until the CO2

alarm screen is displayed.

5. Data Logging

To activate data logging press the key until the logging time setup

screen is displayed. Once the logging function is activated all previously logged

data is written over.

1) The log time interval is displayed in minutes at the bottom of the display.

The logging interval tells the 1008 how often to sample. For example, a logging

interval of 1 minute (01) means the 1008 will log a reading every minute. A log-

ging interval of 10 minutes (10) means the 1008 will log a reading every 10 min-

utes. The log interval time is adjustable from 1 minute to 60 minutes in the fol-

lowing increments: 1, 2, 3, 5, 10, 20, 30, 40, 50, 60 minutes. A maximum of 50

readings can be logged.

2) Use the

3) Once the logging interval is set press the key and the 1008 will return to

the main display and “LOG” will flash indicating the logging function is active. The

1008 will beep each time a reading has been logged.

4) To deactivate data logging press the key and “LOG” will no longer flash.

For data retrieval please see the next section on how to retrieve logged data.

Log time interval in

minutes.

keys to increase or decrease the log interval time.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Table des matières

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur