TPI DC710 Manuel utilisateur

DC710

o be used in conjunc ion wi h a Smar Phone/Table

using he TPI View app.

Smar Flue Gas Analyser

The Value LeaderTM

www.tpieurope.com

Contents

Introduction 1

eneral Overview 1 & 2

Instrument Overview

Front View 3

Back View 4

Basic Analyser Functions

Turning The Analyser On & Connecting 5 & 6

Turning The Analyser Off 7

Specifications 8 & 9

Calibration & Service 10

Warranty 10

Appendix A - eneral Maintenance & Function Tests 11, 12 & 13

Download the PI View App

Download the TPI View app from the Apple®app store or the

oogle®play store to begin using your DC710.

Introduction

Thank you for purchasing TPI brand products. The TPI DC710

combustion analyser is state of the art and easy to use. Connect it to

your smart device and you are ready to perform combustion analysis.

The instrument is ruggedly constructed and comes with a 5 Year

Warranty*

* Warranty subject to annual service/re-calibration by TPI Europe Ltd

or an approved TPI Service Centre. Failure to ensure that

annual service/re-certification is carried out will nulify the 5 Year

Warranty and may lead to additional servicing costs when carried out.

General Overview

The TPI DC710 combustion analyser uses state of the art

electrochemical sensors. This sensor technology provides the longest

lasting most accurate and reliable means for performing combustion

tests. Your analyser will need to be serviced/re-certified annually.

The following guidelines will help prevent damage to your sensors and

keep your anlayser working and giving correct values:

Always use the Mini Pump Protection Filter - see Page 11•

Always periodically check and replace the Mini Pump Protection•

Filter as needed if it becomes blocked or

discoloured - see Appendix A

Always make sure the in-line filter / water trap is installed •

properly - see Appendix A

Always periodically check and replace the in-line filter as•

needed if this becomes saturated or discoloured- see Appendix A

Always remove water or condensation from the inside of the•

in-line filter / water trap assembly prior to performing tests - see

Appendix A

Always use the optional oil filter (p/n A773) when performing•

tests on oil burning equipment

Failure to monitor and perform the above may result in

SLOW and/or INCORRECT READIN S. 1

General Overview (Continued)

This manual will guide you through the functions of the TPI DC710

which will give you many years of reliable service.

You should keep the battery of your DC710 charged so power is

constantly being supplied to your sensors.

Your TPI DC710 Flue as Analyser comes complete with the

following standard accessories:

• TPI DC710 Instrument

• Rubber Boot Ends

• Mini Pump Protection Filter Assembly c/w spare filters (A763)

• Instruction Manual

Your TPI DC710C1 Flue as Analyser comes complete with the

following standard accessories:

• TPI DC710 Instrument

• Rubber Boot Ends

• Soft Carrying Case (A768)

• Flue Sampling Probe (A770)

• In-Line Filter assembly installed on Flue probe (A796)

• Temperature Probe ( K11M)

• Mini Pump Protection Filter Assembly c/w spare filters (A763)

• Instruction Manual

Your TPI DC710 Flue as Analyser has the following options

available to complete your kit:

• Bluetooth Printer (A740BT)

Smart Pressure Meter (SP620)•

Smart Ambient CO2 Meter (SP1000)•

Temperature Pipe Clamps (CK21M)•

CPA1 Probe Kit (CPK3)•

Pocket Combustible as Leak Detector (725L)•

Instrument Overview - Front View

Power Button Used to turn the DC710 on and off.

Illuminates green when power is on.

USB Charger Input Jack Connection for included charger.

Charge Indicator Red = Charging. reen = Fully charged.

Bluetooth Indicator Blue = Connected to smart device.

Red = Disconnected from device.

Pink = Purging

1 Input Jack Connection for the flue probe

temperature lead - see page 6

Gas Sampling Port Connection for Mini Pump Protection

Filter then Flue Probe - see Page 6

2 Input Jack Connection for ambient temperature

probe. If this probe isn’t used the DC710

uses it’s internal temperature sensor -

see Page 6

Rubber End Caps Protects the instrument from accidental

damage

Charge

Indicator

Bluetooth

Indicator

Exhaust

Port

Rubber

End Caps

1 Gas Sample 2

Input Port Input

Power

Button

USB Charger

Input Jack

Instrument Overview - Back View

Magnets: Used to attach the DC710 to a metallic surface

for hands free operation. Note: ensure to check

that surface is not hot or the DC710 may be

damaged.

Hanging Hook: Used to hang the DC710 for hands free

operation.

Information Label: Contains the serial number and additional

information regarding the DC710.

Information

Label

Magnets Hanging Hook Magnets

BASIC ANALYSER FUNC IONS

Analyser Battery

Your combustion analyser is fitted with a Lithium Ion rechargable

battery. It is important to keep battery power to the sensors in your analyser

even when it is not in use. Your analyser battery status is

indicated at the top right corner of the TPI View App. and visible at all times

when connected to the app.

urning he Analyser On & Connecting to the App

Always: - Before turning on please ensure that nothing is

connected to the Gas Sample Port

Press and hold the power button until the power

switch lights on.

Start the TPI View App and tap the center icon to

begin scanning for TPI smart instruments.

A list of available devices will be seen.

Select the DC710 to connect to by tapping on the

desired device on the TPI View app

Once connected the Bluetooth

indicator on the DC710 will turn blue

and the app will display measurement

information.

Connecting to the App (Continued)

Note:It is recommended you perform routine general maintenance on you

analyser to ensure proper function. Please refer to Appendix A for general

maintenance schedule and function tests.

Make sure you are in a “clean air” environment and

tap “Start Pump”.

You will see that on this screen you can view: -

Serial Number of Device Connected

•

Battery Level

•

Calibration Information

•

Fuel Type (which can be changed from the dropdown)

•

Flue as Readings

•

Efficiency (which can be changed from the dropdown)

•

You can also select Ambient CO Testing or Differential

Temperature Feature as well as Creating a Report

from the Readings on the Screen

Connect the Mini Pump Protection Filter

assembly and Flue Probe Tubing

complete with In-Line Filter to the as

Sample Port and the 'K' Type

Thermocouple Plug from the Flue Probe

into Thermocouple (T1) Socket.

The K11M ambient air temperature

probe is connected to the (T2) socket. If

this probe is not used the analyser will

use it’s internal temperature sensor for

ambient air (T2) reference.

WARNING: - Ensure the 'K' type

thermocouple probes are inserted into the

sockets correctly. The plugs are polarity

marked and forcing the plug into the

socket the wrong way may result in

damage to the instrument.

urning he Analyser Off

Always: - Before turning OFF, return the instrument to a clean air

environment and allow the Carbon Monoxide level to return to below 10ppm

and the Oxygen level to return to 20.9%

If the pump is running tap “Stop Pump” to turn the

pump off.

If the CO is above 10ppm or the O2 is below 19%

the Stop Pump icon will be greyed out.

Once the O2 and CO levels are within necessary

limits the Stop Pump icon will be active.

Once the pump is off close the app or disconnect

from the DC710.

Press and hold the power key on the DC710 to

turn the analyser off.

NOTE:

If the app is disconnected before the CO is below 10ppm or the O2 is above

19% and the power key is held down to turn the analyser off, the pump will

continue to run until the CO and O2 are within limits.

The Bluetooth Indicator Light, on the DC710, will Flash Pink whilst the Purge

Period is running. This purge period is necessary to remove any as that is

present before allowing the Pump to Stop and the DC710 turning off leaving

CO or depleted Oxygen inside the DC710 which may cause issues the next

time the DC710 is turned ON.

Once the Purge Period has has completed and within limits the DC710 will

auto power down.

SPECIFICA IONS

Instrument

Operating Temperature Range -10°C to 50°C (-14°F to 122°F)

Battery Type Rechargeable Li-ion (3.7V/2600mA)

Battery Life >6 hours typical

Charger Port USB Connection

Fuel Option (within View app) Natural as, Light Oil, Heavy Oil, LP ,

Bituminous Coal, Anthracite Coal, Coke,

Butane, Wood (Dry), Bagasse,

Wood Pellet

Dimensions 150mm x 100mm x 58mm

Weight 490g

as Sensor Type Electrochemical smart sensors

(O2 and CO)

Flue emperature Probe

Construction Pistol rip with Stainless Steel Shaft

Hose Length 2500mm

Insertion Length 200mm

'K' Type Thermocouple Accuracy +/- 0.3%, +/- 2°F (1°C)

Maximum Temperature 1472°F (800°C)

Gases

Range Resolution Accuracy

Oxygen 0-25% 0.1% +/- 0.3%

Carbon Monoxide 0-10,000 ppm 1 ppm +/- 5 ppm or 5%

Whichever is greater

Carbon Dioxide 0-25% 0.1% Calculated

CO/CO2 Ratio 0-0.999 0.001 Calculated

Combustion Efficiency 0-100% 0.1% Calculated

Autres manuels pour DC710

Table des matières

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur