Texas Instruments TSC2007EVM Manuel utilisateur

User's GuideSLAU199 – March 2007

TSC2007EVM and TSC2007EVM-PDK User's Guide

This user's guide describes the characteristics, operation, and use of theTSC2007EVM, both by itself and as part of the TSC2007EVM-PDK. This evaluationmodule (EVM) is a 4-wire touch screen controller EVM which also has auxiliary inputand temperature measurement capabilities. A complete circuit description, schematicdiagram, and bill of materials are included.

The following related documents are available through the Texas Instruments Web siteat www.ti.com .

Table 1. EVM-Compatible Device Data Sheets

DEVICE LITERATURE NUMBER

TSC2007 SBAS405TAS1020B SLES025REG1117-5 SBVS001TPS767D318 SLVS209SN74LVC125A SCAS290SN74LVC1G125 SCES223SN74LVC1G07 SCES296

Contents1 EVM Overview ............................................................................................................... 22 Analog Interface .............................................................................................................. 23 Digital Interface .............................................................................................................. 34 Power Supplies .............................................................................................................. 35 EVM Operation ............................................................................................................... 46 Kit Operation ................................................................................................................. 57 EVM Bill of Materials ........................................................................................................ 98 TSC2007EVM Schematic ................................................................................................. 119 USB-MODEVM Schematic ................................................................................................ 11

List of Figures

1 TSC2007EVM-PDK Block Diagram ...................................................................................... 62 Default Software Screen ................................................................................................... 7

List of Tables

1 EVM-Compatible Device Data Sheets .................................................................................... 12 Analog Interface Pinout ..................................................................................................... 23 Digital Interface Pinout ...................................................................................................... 34 Power Supply Pinout ........................................................................................................ 35 Power Selection Options - JMP1 .......................................................................................... 36 List of Jumpers ............................................................................................................... 57 TSC2007EVM Bill of Materials ............................................................................................. 98 USB-MODEVM Bill of Materials .......................................................................................... 10

SLAU199 – March 2007 TSC2007EVM and TSC2007EVM-PDK User's Guide 1Submit Documentation Feedback

www.ti.com

1 EVM Overview

1.1 Features

1.2 Introduction

2 Analog Interface

EVM Overview

•Full-featured evaluation board for the TSC2007 4-wire resistive touch screen controller (TSC).•Modular design for use with a variety of DSP and microcontroller interface boards.

The TSC2007EVM-PDK is a complete evaluation kit, which includes a USB-based motherboard andevaluation software for use with a personal computer running Microsoft Windows™ operating systems.

The TSC2007EVM is in the Texas Instruments modular EVM form factor, which allows direct evaluation ofthe performance and operating characteristics of the TSC2007, and eases software development andsystem prototyping. This EVM is compatible with the 5-6K Interface Evaluation Module (SLAU104 ) fromTexas Instruments and additional third-party boards such as the NI Speedy-33™ from NationalInstruments Corporation. (www.ni.com )

The TSC2007EVM-PDK is a complete evaluation/demonstration kit, which includes a USB-basedmotherboard called the USB-MODEVM interface board and evaluation software for use with a personalcomputer running Microsoft Windows operating systems.

For maximum flexibility, the TSC2007EVM is designed for easy interfacing to multiple analog sources.Samtec part numbers SSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P provide a convenient 10-pin,dual-row header/socket combination at J1. This header/socket provides access to the analog input pins ofthe TSC. Consult Samtec at www.samtec.com , or call 1-800-SAMTEC-9 for a variety of mating connectoroptions.

Table 2. Analog Interface Pinout

PIN NUMBER SIGNAL DESCRIPTION

J1.2 X+ Touch screen X+ electrodeJ1.4 X- Touch screen X- electrodeJ1.6 Y+ Touch screen Y+ electrodeJ1.8 Y- Touch screen Y- electrodeJ1.10 UnusedJ1.12 AUX Auxiliary input, 0 V to VREFJ1.14 UnusedJ1.16 UnusedJ1.18 UnusedJ1.20 UnusedJ1.15 UnusedJ1.1-J1.19 (odd) AGND Analog ground connections (except J1.15)

NI Speedy-33 is a trademark of Hyperception, Inc.I

C is a trademark of Koninklijke Philips Electronics N.V., The Netherlands.Windows is a trademark of Microsoft Corporation.SPI is a trademark of Motorola, Inc.

2TSC2007EVM and TSC2007EVM-PDK User's Guide SLAU199 – March 2007Submit Documentation Feedback

www.ti.com

3 Digital Interface

4 Power Supplies

4.1 TSC Power

Digital Interface

The TSC2007EVM is designed to easily interface with multiple control platforms. Samtec part numbersSSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P provide a convenient 10-pin, dual-row header/socketcombination at J2. This header/socket provides access to the digital control and serial data pins of theTSC. Consult Samtec at www.samtec.com or call 1-800-SAMTEC-9 for a variety of mating connectoroptions.

Table 3. Digital Interface Pinout

PIN NUMBER SIGNAL DESCRIPTION

J2.15 PENIRQ Pen Interrupt Output from TSCJ2.16 SCL I

C™ bus serial clockJ2.4, J2.10, J2.18 DGND Digital groundJ2.1-J2.19 (odd, except UnusedJ2.15)

J2.20 SDA I

C bus data line

J3 provides connection to the common power bus for the TSC2007EVM. Power is supplied on the pinslisted in Table 4 .

Table 4. Power Supply Pinout

SIGNAL PIN NUMBER SIGNAL

Unused 1 2 UnusedUnused 3 4 UnusedDGND 5 6 AGND+1.8VD 7 8 Unused+3.3VD 9 10 Unused

When power is supplied to J3, JMP1 allows for one of two different DC voltages to be selected as powerfor the TSC. See the schematic and PCB silkscreen for details.

The TSC2007EVM-PDK motherboard (the USB-MODEVM interface board) supplies power to J3 of theTSC2007EVM. Power for the motherboard is supplied either through its USB connection or via terminalblocks on the board.

Power for the TSC2007 VCC can be supplied either from the +1.8VD terminal or from the +3.3VDterminal. JMP1 selects which of these voltages is routed to the TSC2007. When JMP1 is in the defaultfactory condition (shunt on pins 2-3), power to the TSC comes from J3.9 (+3.3VD). When the shunt isinstalled on JMP1 pins 1-2, power comes from J3.7 (+1.8VD). Removing the shunt on JMP1, the user canconnect any DC power supply between 1.2VD and 3.6VD to VCC by connecting the power to JMP1 pin 2.

Table 5. Power Selection Options - JMP1

SHUNT ON PINS VDD VOLTAGE FROM J3 PIN

1-2 +1.8VD 72-3 +3.3VD 9Removed +1.2VD and +3.6VD External

SLAU199 – March 2007 TSC2007EVM and TSC2007EVM-PDK User's Guide 3Submit Documentation Feedback

www.ti.com

4.2 Stand-Alone Operation

4.3 USB-MODEVM Interface Power

5 EVM Operation

5.1 Analog Input

5.2 Digital Control

5.3 Default Jumper Locations

EVM Operation

When used as a stand-alone EVM, power can be applied to TP1, referenced to TP3.

CAUTION

Verify that all power supplies are within the safe operating limits shown on theTSC2007 data sheet (SBAS405 ) before applying power to the EVM.

The USB-MODEVM interface board can be powered from several different sources:•USB

•6 VDC-10 VDC AC/DC external wall supply (not included)•Laboratory power supply

When powered from the USB connection, JMP6 should have a shunt from pins 1-2 (this is the defaultfactory configuration). When powered from 6 VDC-10 VDC, either through the J8 terminal block or J9barrel jack, JMP6 should have a shunt installed on pins 2-3. If power is applied in any of these ways,onboard regulators generate the required supply voltages, and no further power supplies are necessary.

If laboratory supplies are used to provide the individual voltages required by the USB-MODEVM interfaceboard, JMP6 should have no shunt installed. Voltages then are applied to J2 (+5VA), J3 (+5VD), J4(+1.8VD), and J5 (+3.3VD). The +1.8VD and +3.3VD also can be generated on the board by the onboardregulators from the +5VD supply; to enable this supply, the switches on SW1 need to be set to enable theregulators by placing them in the ON position (lower position, looking at the board with text readingright-side up). If +1.8VD and +3.3VD are supplied externally, disable the onboard regulators by placingSW1 switches in the OFF position.

Each power supply voltage has an LED (D1-D7) which lights when the power supplies are active.

The following section provides information on the analog input, digital control, and general operatingconditions of the TSC2007EVM.

The analog input sources (touch screen and auxiliary input) can be applied directly to J1 (top or bottomside) or through signal-conditioning modules available for the modular EVM system.

The digital control signals can be applied directly to J2 (top or bottom side). The modular TSC2007EVMalso can be connected directly to a DSP or microcontroller interface board, such as the USB-MODEVMinterface board if purchased as part of the TSC2007EVM-PDK. See the product folder for the TSC2007 fora current list of compatible interface and/or accessory boards.

Table 6 provides a list of jumpers found on the EVM and their factory default conditions.

TSC2007EVM and TSC2007EVM-PDK User's Guide4 SLAU199 – March 2007Submit Documentation Feedback

www.ti.com

6 Kit Operation

6.1 TSC2007EVM-PDK Block Diagram

Kit Operation

Table 6. List of Jumpers

JUMPER SHUNT POSITION JUMPER DESCRIPTION

JMP1 2-3 Analog power select (default is +3.3VD)JMP2 Closed EEPROM address select. When installed and used with the USB-MODEVM, firmware for themotherboard is executed from the EEPROM on the TSC2007EVM. This is the default mode.

The following section provides information on using the TSC2007EVM-PDK, including setup, programinstallation, and program usage.

A block diagram of the TSC2007EVM-PDK is shown in Figure 1 . The evaluation kit consists of two circuitboards connected together. The motherboard is designated as the USB-MODEVM interface board; thedaughtercard is the TSC2007EVM described previously in this manual.

SLAU199 – March 2007 TSC2007EVM and TSC2007EVM-PDK User's Guide 5Submit Documentation Feedback

www.ti.com

TAS1020B

USB 8052

microcontroller

USB

EVM Position 1

EVM Position 2

Control Interface

Audio Interface

TSC2007EVM

TSC2007

SPI, I2C

I2S, AC97

X+

X−

Y+

Y−

AUX

SDA

SCL

PENIRQ

6.2 Quick Start

Kit Operation

Figure 1. TSC2007EVM-PDK Block Diagram

The USB-MODEVM interface board is intended to be used in USB mode, where control of the installedEVM is accomplished using the onboard USB controller device. However, provision is made for driving allthe data buses (I

C, SPI™, and I

S/AC97) externally. The source of these signals is controlled by SW2 onthe USB-MODEVM.

Before installing the TSC2007EVM board on top of the USB-MODEVM board, check SW2-1, SW2-2, andSW2-3 on the USB-MODEVM board to ensure that at least one of these three is OFF

Ensure that the TSC2007EVM is installed on the USB-MODEVM interface board. The TSC2007EVMshould be installed in the topmost position, using J11, J12, and J13 on the USB-MODEVM.

6TSC2007EVM and TSC2007EVM-PDK User's Guide SLAU199 – March 2007Submit Documentation Feedback

www.ti.com

Kit Operation

Place the CD-ROM into your PC CD-ROM drive. Locate the Setup program on the disk, and run it. TheSetup program will install the TSC2007 Evaluation software on your PC.

Accept the license agreement, and continue the installation.

When the installation completes, click Finish on the TSC2007EVM installer window. You may be promptedto restart your computer.

When installation is complete, attach a USB cable from your PC to the USB-MODEVM interface board. Asconfigured at the factory, the board is powered from the USB interface; so, the power indicator LEDs onthe USB-MODEVM should light. Once this occurs, launch the TSC2007 evaluation software on your PC. Itis suggested that users read the readme_install.txt file for up-to-date, step-by-step instructions.

The software should automatically find the TSC2007EVM, and a screen similar to the one shown inFigure 2 should appear.

Figure 2. Default Software Screen

In order to use the touch screen features, a user needs to connect a 4-wire resistive touch screen to J1 ofthe TSC2007EVM, as described previously.

SLAU199 – March 2007 TSC2007EVM and TSC2007EVM-PDK User's Guide 7Submit Documentation Feedback

www.ti.com

6.3 USB-MODEVM Interface Board

6.4 Program Description

6.4.1 Touch Screen Functions Panel

6.4.2 Data Acquisition Functions Panel

6.4.3 Configuration Panel

Kit Operation

The simple diagram shown in Figure 1 shows only the basic features of the USB-MODEVM interfaceboard. The board is built around a TAS1020B streaming audio USB controller with an 8051-based core.The board features two positions for modular EVMs, or one double-wide serial modular EVM may beinstalled.

For use with the TSC2007, the TSC2007EVM is installed in the topmost EVM slot, which connects theTSC2007 digital control interface to the I

C port, realized using the TAS1020B. Because the TSC2007 hasno audio features, the lower EVM slot, which is connected to the TAS1020B digital audio interface, is notused.

As configured from the factory, the board is ready to use with the TSC2007EVM except for SW2, in whichcase at least one of SW2-1, SW2-2, and SW2-3 must be set to OFF.

After the TSC2007EVM-PDK software installation (described in Section 6.2 ), evaluation and developmentwith the TSC2007 can begin.

The touch screen box in this panel is updated when a touch is detected on the touch screen. As the touchscreen is drawn on, the motion on the touch screen is translated into pixels on this box. The softwaretakes X, Y, and Z readings which are shown to the right of the touch screen box. As the touch pressure isincreased, the pixel size increases; a lighter touch results in smaller pixel sizes.

The Z-value displayed is not what is described in the TSC2007 data sheet, because in the data sheetequation, it is assumed that the sheet resistance of the touch screen being used is known. The value usedin this program is calculated by Equation 2 of the TSC2007 data sheet, but without multiplying it by theR

X-plate

resistance. This value ranges from 0 to 3, and larger, with larger numbers representing a moreforceful press on the screen. Using the Maximum Z Value to Display knob, you can set a threshold sothat the program does not display lightly pressed points. This threshold setting helps to eliminate displayof spurious points that may result from touch screen mechanical bouncing.

The display can be cleared by pressing the Clear Graph button on the screen.

The TSC2007 has provision for measuring one auxiliary input voltages (AUX1) and temperature. Thispanel displays the measured values for these parameters. Measurements are updated only when thetouch screen is not being pressed.

Temperature is displayed using both methods described in the TSC2007 data sheet. Using the TEMP0and TEMP1 measurements, a temperature reading with 2°C resolution and accuracy is achieved. Usingonly the TEMP0 measurement, a reading with 0.3°C resolution is possible, but this option requiresknowing the TEMP0 value at +25°C; this would normally be a calibration that the user would perform. Thisprogram assumes that TEMP0 = 600 mV at +25°C.

The TSC2007 can be configured to operate in 8-bit or 12-bit resolution modes. Control over the modeused is selected in this panel.

In the middle of this panel is an indicator light that shows the I

C Bus Status. If the TSC2007 isacknowledging the address sent, the light is green; if the TSC2007 cannot acknowledge, the light is red.The address to which the TSC2007 is set is shown in binary format in the box labeled Device AddressA1-A0. The address set here should be "00" when using the TSC2007EVM. Even though the TSC2007has two pins, A0 and A1, for users to select four different I2C addresses, the TSC2007EVm has only afixed address 1001000b, where A0=A1="0", because both A0 and A1 are tied to ground. See theTCS2007EVM schematic provided in this document.

8TSC2007EVM and TSC2007EVM-PDK User's Guide SLAU199 – March 2007Submit Documentation Feedback

www.ti.com

6.4.4 Datalogging

7 EVM Bill of Materials

EVM Bill of MaterialsThe two power-down bits of the TSC2007 can be set from this panel as well. A brief description of themode selected is shown on the screen when setting these bits; see Table 3 ( Command Byte Definitions)of the TSC2007 data sheet (SBAS405 ) for details on what these bits do.

The software can record the data it takes from the TSC2007 to a tab-delimited file, suitable for importinginto spreadsheets. To do this, first go into the File menu, and select Log Data to File..., which opens afile-select window and allows you to specify a file to which to write the data. At the same time, this enablesthe Datalogging menu.

When ready to begin recording data to a file, select Datalogging →Start Logging. Data is written to the fileuntil Datalogging →Stop Logging is selected. When the screen is not touched, the AUX and TEMP valuesare written to the file, and the X, Y, Z1, and Z2 parameters are written to the file with values of 9999, toindicate that they are not updated. When the screen is touched, the X, Y, Z1, and Z2 parameters arewritten while the AUX and TEMP values are written to the file as 9999. Because the program constantlyupdates at a rate of about 400 readings per second, datalog files can quickly grow large; therefore, logonly that data which is necessary.

The format of the data file has the first column as the time in milliseconds (which is just a timer in theprogram; it can arbitrarily start at any number), then X, Y, Z1, Z2, AUX, TEMP0, and TEMP1 columns.Every new reading is a new row in the file.

Table 7 and Table 8 contain a complete bill of materials for the modular TSC2007EVM evaluation boardand the USB-MODEVM interface board, respectively (included only in the TSC2007EVM-PDK).

Table 7. TSC2007EVM Bill of Materials

Reference Designator Description Manufacturer Manufacturer's Part Number

R1 100 Ω1/8W 5% Chip Resistor Panasonic ERJ-6GEYJ101VR2, R3 2.7k Ω1/10W 5% Chip Resistor Panasonic ERJ-3GEYJ272VR4 20k Ω1/10W 5% Chip Resistor Panasonic ERJ-3GEYJ272VC1, C3, C8 0.1µF 16V Ceramic Chip TDK C1608X7R1C105KCapacitor, +/ - 10%, X7RC2 10µF 16V Ceramic Chip TDK C3216X5R1C106MCapacitor, +/ - 20%, X5RC4-C7 Ceramic Chip Capacitor -Not installedU1 I

C Touch Screen Controller Texas Instruments TSC2007IZZZU2 64K I

C EEPROM MicroChip 24AA64-I/SNTSC2007EVM PCB Texas Instruments 6486822J1A, J2A 20-pin SMT plug Samtec TSM-110-01-L-DV-PJ1B, J2B 20-pin SMT socket Samtec SSW-110-22-F-D-VS-KJ3A 10-pin SMT plug Samtec TSM-105-01-L-DV-PJ3B 10-pin SMT socket Samtec SSW-105-22-F-D-VS-KJMP2 2-position jumper , 0 .1" spacing Samtec TSW-102-07-L-SJMP1 3-position jumper , 0 .1" spacing Samtec TSW-103-07-L-STP1 Miniature test point terminal Keystone Electronics 5000TP2 Miniature test point terminal Keystone Electronics 5001TP4, TP5, TP6, TP7 Miniature test point terminal Keystone Electronics 5002TP8 Miniature test point terminal Keystone Electronics 5004TP9, TP10, TP11 Miniature test point terminal Keystone Electronics 5003Header shorting block Samtec SNT-100-BK-G-H

SLAU199 – March 2007 TSC2007EVM and TSC2007EVM-PDK User's Guide 9Submit Documentation Feedback

www.ti.com

EVM Bill of Materials

Table 8. USB-MODEVM Bill of Materials

Reference Designator Description Manufacturer Manufacturer's Part Number

R4 10 Ω1/10W 5% Chip Resistor Panasonic ERJ-3GEYJ100VR10, R11 27.4 Ω1/16W 1% Chip Resistor Panasonic ERJ-3EKF27R4VR20 75 Ω1/4W 1% Chip Resistor Panasonic ERJ-14NF75R0UR19 220 Ω1/10W 5% Chip Resistor Panasonic ERJ-3GEYJ221VR14, R21, R22 390 Ω1/10W 5% Chip Resistor Panasonic ERJ-3GEYJ391VR13 649 Ω1/16W 1% Chip Resistor Panasonic ERJ-3EKF6490VR9 1.5K Ω1/10W 5% Panasonic ERJ-3GEYJ152VChip ResistorR1, R2, R3, R5, R6, R7, R8 2.7K Ω1/10W 5% Panasonic ERJ-3GEYJ272VChip ResistorR12 3.09K Ω1/16W 1% Panasonic ERJ-3EKF3091VChip ResistorR15, R16 10K Ω1/10W 5% Panasonic ERJ-3GEYJ103VChip ResistorR17, R18 100K Ω1/10W 5% Panasonic ERJ-3GEYJ104VChip ResistorRA1 10K Ω1/8W Octal Isolated CTS Corporation 742C163103JTRResistor ArrayC18, C19 33pF 50V Ceramic TDK C1608C0G1H330JChip Capacitor, ±5%, NPOC13, C14 47pF 50V Ceramic TDK C1608C0G1H470JChip Capacitor, ±5%, NPOC20 100pF 50V Ceramic TDK C1608C0G1H101JChip Capacitor, ±5%, NPOC21 1000pF 50V Ceramic TDK C1608C0G1H102JChip Capacitor, ±5%, NPOC15 0.1µF 16V Ceramic TDK C1608X7R1C104KChip Capacitor, ±10%,X7RC16, C17 0.33µF 16V Ceramic TDK C1608X5R1C334KChip Capacitor, +/-20%,Y5VC9, C10, C11, C12, C22, C23, 1µF 6.3V Ceramic TDK C1608X5R0J105KC24, C25, C26, C27, C28 Chip Capacitor, ±10%, X5RC1, C2, C3, C4, C5, C6, C7, 10µF 6.3V Ceramic TDK C3216X5R0J106KC8 Chip Capacitor, ±10%, X5RD1 50V, 1A, Diode MELF SMD Micro Commercial Components DL4001D2 Yellow Light Emitting Diode Lumex SML-LX0603YW-TRD3, D4, D6, D7 Green Light Emitting Diode Lumex SML-LX0603GW-TRD5 Red Light Emitting Diode Lumex SML-LX0603IW-TRQ1, Q2 N-Channel MOSFET Zetex ZXMN6A07FX1 6MHz Crystal SMD Epson MA-505 6.000M-C0U8 USB Streaming Controller Texas Instruments TAS1020BPFBU2 5V LDO Regulator Texas Instruments REG1117-5U9 3.3V/1.8V Dual Output LDO Texas Instruments TPS767D318PWPRegulatorU3, U4 Quad, Tri-State Buffers Texas Instruments SN74LVC125APWU5, U6, U7 Single IC Buffer Driver with Texas Instruments SN74LVC1G07DBVROpen Drain o/pU10 Single Tri-State Buffer Texas Instruments SN74LVC1G125DBVRU1 64K 2-Wire Serial EEPROM Microchip 24LC64I/SNI

CUSB-MODEVM PCB Texas Instruments 6463995

10 TSC2007EVM and TSC2007EVM-PDK User's Guide SLAU199 – March 2007Submit Documentation Feedback

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Texas Instruments Matériel informatique

Texas Instruments

Texas Instruments AM1808 Manuel du produit

Texas Instruments

Texas Instruments Hercules TMS570LS12 Series Manuel utilisateur

Texas Instruments

Texas Instruments LM60EVM Manuel utilisateur

Texas Instruments

Texas Instruments OMAP5910 Manuel utilisateur

Texas Instruments

Texas Instruments TPA6135A2 EVM Manuel utilisateur

Texas Instruments

Texas Instruments DRV830x Rev D. Manuel utilisateur

Texas Instruments

Texas Instruments TMAG5170D Manuel utilisateur

Texas Instruments

Texas Instruments TLV320AIC12KEVMB-K Manuel utilisateur

Texas Instruments

Texas Instruments Sitara AM1335 Series Manuel utilisateur

Texas Instruments

Texas Instruments ADS41 Series Manuel utilisateur

Texas Instruments

Texas Instruments BQ25638 Series Manuel utilisateur

Texas Instruments

Texas Instruments TMS320 Series Manuel utilisateur

Texas Instruments

Texas Instruments System-Side Impedance Track bq27500 Manuel utilisateur

Texas Instruments

Texas Instruments Jacinto 7 DRA829 Manuel utilisateur

Texas Instruments

Texas Instruments DS250DF810EVM Manuel utilisateur

Texas Instruments

Texas Instruments TMS320TCI6482 Mode d’emploi

Texas Instruments

Texas Instruments TVP5158 Manuel utilisateur

Texas Instruments

Texas Instruments TAS5707EVM Manuel utilisateur

Texas Instruments

Texas Instruments INA260EVM-PDK Manuel utilisateur

Texas Instruments

Texas Instruments TUSB522P Manuel utilisateur

Texas Instruments

Texas Instruments OMAP5912 Manuel utilisateur

Texas Instruments

Texas Instruments TAS5066PAG Manuel utilisateur

Texas Instruments

Texas Instruments BoosterPack BOOSTXL-RS232 Manuel utilisateur

Texas Instruments

Texas Instruments TPS61196EVM-600 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur