Texas Instruments System-Side Impedance Track bq27500 Manuel utilisateur

www.ti.com

1 INTRODUCTION

1.1 FEATURES 1.2 APPLICATIONS

1.3 DESCRIPTION

Host System

Single Cell Li-Ion

Battery Pack

PACK-

PROTECTION

CHG

DSG

Temp

Sense

Battery

Good

Current

Sense

I2C T

LDO

PACK+

Voltage

Sense

Battery

Low

Warning

FETs

bq27500/1

RID

Sense*

* bq27501 Only

Power

Management

Controller

bq27500

bq27501System-Side Impedance Track™ Fuel Gauge

SLUS785 – SEPTEMBER 2007

•Battery Fuel Gauge for 1-Series Li-Ion

•SmartphonesApplications

•PDAs•Resides on System Main Board

•Digital Still and Video Cameras– Works with Embedded or Removable

•Handheld TerminalsBattery Packs

•MP3 or Multimedia Players•Two Varieties

– bq27500: Uses PACK+,PACK-, and TBattery Terminals– bq27501: Includes Battery Pack ID Resistor(RID) Terminal

The Texas Instruments bq27500/01 System-SideLi-Ion Battery Fuel Gauge is a micro-controller•Micro-Controller Peripheral Provides:

peripheral that provides fuel gauging for single cell– Accurate Battery Fuel Gauging

Li-Ion battery packs. The device requires little system– Internal Temperature Sensor for System

micro-controller firmware development. TheTemperature Reporting

bq27500/01 resides on the system’s main board, and–Battery Low Interrupt Warning

manages an embedded battery (non-removable) or a–Battery Insertion Indicator

removable battery pack.– Battery ID Detection– 96 bytes of Non-Volatile Scratch Pad

The bq27500/01 uses the patented ImpedanceFLASH

Track™ algorithm for fuel gauging, and providesinformation such as remaining battery capacity•Battery Fuel Gauge Based on Patented

(mAh), state-of-charge (%), run-time to empty (min.),Impedance Track™ Technology

battery voltage (mV), and temperature ( °C).– Models the Battery Discharge Curve forAccurate Time-to-Empty Predictions

Battery fuel gauging with the bq27500 requires only– Automatically Adjusts for Battery Aging,

PACK+ (P+), PACK- (P-), and Thermistor (T)Battery Self Discharge, and

connections to a removable battery pack orTemperature/Rate Inefficiencies

embedded battery circuit. The bq27501 works with– Low Value Sense Resistor (10m Ωor Less)

identification resistors in battery packs, to gauge•I

C™ Interface for Connection to System

batteries of different fundamental chemistries and/orMicro-Controller Port

significantly different rated capacities.•12-Pin 2,5 mm ×4,0 mm SON Package

TYPICAL APPLICATION

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this document.Impedance Track is a trademark of Texas Instruments.I

C is a trademark of Philips Electronics.

UNLESS OTHERWISE NOTED this document contains

Copyright © 2007, Texas Instruments IncorporatedPRODUCTION DATA information current as of publication date.Products conform to specifications per the terms of TexasInstruments standard warranty. Production processing does notnecessarily include testing of all parameters.

www.ti.com

Contents

bq27500

bq27501

System-Side Impedance Track™ Fuel Gauge

SLUS785 – SEPTEMBER 2007

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed inconductive foam during storage or handling to prevent electrostatic damage to the MOS gates.

1 INTRODUCTION .......................................... 14.2 DATA FLASH INTERFACE ......................... 161.1 FEATURES ........................................... 14.3 MANUFACTURER INFORMATION BLOCKS ...... 171.2 APPLICATIONS ...................................... 14.4 ACCESS MODES ................................... 171.3 DESCRIPTION ....................................... 14.5 SEALING/UNSEALING DATA FLASH .............. 172 DEVICE INFORMATION ................................. 34.6 DATA FLASH SUMMARY ........................... 182.1 AVAILABLE OPTIONS ............................... 35 FUNCTIONAL DESCRIPTION ........................ 202.2 PIN DIAGRAMS ...................................... 35.1 FUEL GAUGING .................................... 202.3 TERMINAL FUNCTIONS ............................. 35.2 IMPEDANCE TRACK™ VARIABLES ............... 213 ELECTRICAL SPECIFICATIONS ...................... 45.3 DETAILED DESCRIPTION OF DEDICATED PINS .233.1 ABSOLUTE MAXIMUM RATINGS ................... 45.4 TEMPERATURE MEASUREMENT ................. 263.2 RECOMMENDED OPERATING CONDITIONS ...... 45.5 OVERTEMPERATURE INDICATION ............... 265.6 CHARGING AND CHARGE-TERMINATION3.3 POWER-ON RESET .................................. 4

INDICATION ......................................... 263.4 INTERNAL TEMPERATURE SENSORCHARACTERISTICS ................................. 55.7 POWER MODES .................................... 273.5 HIGH FREQUENCY OSCILLATOR .................. 55.8 POWER CONTROL ................................. 293.6 LOW FREQUENCY OSCILLATOR ................... 55.9 AUTOCALIBRATION ................................ 303.7 INTEGRATING ADC (COULOMB COUNTER)

6 APPLICATION-SPECIFIC INFORMATION .......... 31CHARACTERISTICS ................................. 5

6.1 BATTERY PROFILE STORAGE AND SELECTION 313.8 ADC (TEMPERATURE AND CELL

6.2 APPLICATION-SPECIFIC FLOW AND CONTROL .31MEASUREMENT) CHARACTERISTICS ............. 5

7 COMMUNICATIONS .................................... 333.9 DATA FLASH MEMORY CHARACTERISTICS ...... 6

7.1 I

C INTERFACE ..................................... 333.10 I

C-COMPATIBLE INTERFACE COMMUNICATION

8 REFERENCE SCHEMATICS .......................... 34TIMING CHARACTERISTICS ........................ 6

8.1 SCHEMATIC ........................................ 344 GENERAL DESCRIPTION .............................. 84.1 DATA COMMANDS .................................. 9

2Contents Submit Documentation Feedback

www.ti.com

2 DEVICE INFORMATION

2.1 AVAILABLE OPTIONS

2.2 PIN DIAGRAMS

BAT

VSS

SRN

SRP

VCC

BAT_GD

SDA

SCL

BAT_LOW_

BI/TOUT

BAT

VSS

VCC

BAT_LOW_

BI/TOUT

SRN

SRP

BAT_GD

SDA

SCL

RID

bq27500 bq27501

2.3 TERMINAL FUNCTIONS

bq27500

bq27501System-Side Impedance Track™ Fuel Gauge

SLUS785 – SEPTEMBER 2007

COMMUNICATION TAPE and REELPART NUMBER PACKAGE

(1)

FORMAT QUANTITY

bq27500DRZR 3000bq27500DRZT 30012-pin, 2,5 mm x 4,0 mm

–40 °C to 85 °C I

CSONbq27501DRZR

(2)

3000bq27501DRZT

(2)

300

(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TIwebsite at www.ti.com .(2) Product Preview

TERMINAL

I/O

(1)

DESCRIPTIONNAME NAMEPIN NO.

bq27500 bq27501

Battery Low output indicator. Active high by default, though polarity can be configured1 BAT_LOW BAT_LOW O

through the [BATL_POL] in Operation Configuration Push-pull output.Battery-insertion detection input. Power pin for pack thermistor network. Thermistor2 BI/TOUT BI/TOUT I/O

multiplexer control pin. Open-drain I/O. use with pull-up resistor > 1M Ω(1.8M Ωtypical)3 TS TS P Pack thermistor voltage sense (use 103AT-type thermistor). ADC input.4 BAT BAT I Cell-voltage measurement input. ADC input.5 V

P Processor power input. Decouple with 0.1 μF capacitor, minimum.6 V

P Device ground.Analog input pin connected to the internal coulomb-counter where SRP is nearest the7 SRP SRP IA

CELL- connection. Connect to 5-20m Ωsense resistor.Analog input pin connected to the internal coulomb-counter where SRN is nearest the8 SRN SRN IA

PACK- connection. Connect to 5-20m Ωsense resistor.No connection (bq27500). Resistor ID input (bq27501). Analog input with current sourcing9 NC RID –, I

capabilities.

Slave I

C serial communications data line for communication with system ( Master).10 SDA SDA I/O

Open-drain I/O. Use with 10k Ωpull-up resistor (typical).Slave I

C serial communications clock input line for communication with system ( Master).11 SCL SCL I

Open-drain I/O. Use with 10k Ωpull-up resistor (typical).Battery Good indicator. Active low by default, though polarity can be configured through12 BAT_GD BAT_GD O

the [BATG_POL] of Operation Configuration. Open-drain output.

(1) I/O = Digital Input/Output, IA = Analog Input, P = Power Connection

Submit Documentation Feedback DEVICE INFORMATION 3

www.ti.com

3 ELECTRICAL SPECIFICATIONS

3.1 ABSOLUTE MAXIMUM RATINGS

3.2 RECOMMENDED OPERATING CONDITIONS

3.3 POWER-ON RESET

bq27500

bq27501

System-Side Impedance Track™ Fuel Gauge

SLUS785 – SEPTEMBER 2007

over operating free-air temperature range (unless otherwise noted)

(1)

PARAMETER VALUE UNIT

Supply voltage range –0.3 to 2.75 VV

IOD

Open-drain I/O pins (BI_TOUT, SDA, SDL, BAT_GD) –0.3 to 6 VV

BAT

BAT input pin –0.3 to +6V

Input voltage range to all other pins (TS, SRP, SRN, RID [bq27501 only], NC –0.3 to V

+ 0.3 V[bq27500 only])

1 kVESD Human Body Model (HMB)

2 kVT

Functional temperature range –40 to 100 °CT

STG

Storage temperature range –65 to 150 °C

(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratingsonly, and functional operation of the device at these or any other conditions beyond those indicated under recommended operatingconditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

= 25 °C, V

= 2.5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

Supply Voltage 2.4 2.5 2.6 VI

Normal operating mode current

(1)

95 μAI

SLP

Low-power storage mode current

(2)

15 μAI

Hibernate operating mode current

(3)

2μAV

Output voltage low (SDA, BAT_LOW, BI/TOUT) I

= 0.5 mA 0.4 VV

OH(PP)

Output high voltage (BAT_LOW) I

= –1 mA V

–0.5 VExternal pull-up resistorV

OH(OD)

Output high voltage (SDA, SCL, BI/TOUT) V

–0.5 Vconnected to V

Input voltage low (SDA, SCL) –0.3 0.8

IH(OD)

Input voltage high (SDA, SCL, BI/TOUT) 2 6C

Input capacitance 5 pFV

Input voltage range (TS, RID [bq27501 only]) V

–0.125 2 VV

Input voltage range (BAT) V

–0.125 5 VV

Input voltage range (SRP, SRN) V

–0.125 0.125 Vt

PUCD

Power up communication delay 250 msT

Operating free-air temperature range –40 85 °C

(1) High level of system activity.(2) Low level of system activity.(3) Fuel gauge algorithm power inactive. Only able to receive I

C communication.

= –40 °C to 85 °C, Typical Values at T

= 25 °C and V

BAT

= 3.6 V (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

IT+

Positive-going battery voltage input at V

2.09 2.20 2.31 VV

HYS

45 115 185 mV

ELECTRICAL SPECIFICATIONS4Submit Documentation Feedback

www.ti.com

3.4 INTERNAL TEMPERATURE SENSOR CHARACTERISTICS

3.5 HIGH FREQUENCY OSCILLATOR

3.6 LOW FREQUENCY OSCILLATOR

3.7 INTEGRATING ADC (COULOMB COUNTER) CHARACTERISTICS

3.8 ADC (TEMPERATURE AND CELL MEASUREMENT) CHARACTERISTICS

bq27500

bq27501System-Side Impedance Track™ Fuel Gauge

SLUS785 – SEPTEMBER 2007

= –40 °C to 85 °C, 2.4 V < V

< 2.6 V; Typical Values at T

= 25 °C and V

= 2.5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

TEMP

Temperature sensor voltage gain –2.0 mV/ °C

= –40 °C to 85 °C, 2.4 V < V

< 2.6 V; Typical Values at T

= 25 °C and V

= 2.5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

OSC

Operating frequency 2.097 MHzT

= 0 °C to 60 °C –2.0% 0.38% 2.0%f

EIO

Frequency error

(1) (2)

= –20 °C to 70 °C –3.0% 0.38% 3.0%T

= –40 °C to 85 °C –4.5% 0.38% 4.5%t

SXO

Start-up time

(3)

2.5 5 ms

(1) The frequency error is measured from 2.097 MHz.(2) The frequency drift is included and measured from the trimmed frequency at V

= 2.5V, T

= 25 °C.(3) The startup time is defined as the time it takes for the oscillator output frequency to be ±3%.

= –40 °C to 85 °C, 2.4 V < V

< 2.6 V; Typical Values at T

= 25 °C and V

= 2.5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

LOSC

Operating frequency 32.768 kHzT

= 0 °C to 60 °C –1.5% 0.25% 1.5%f

LEIO

Frequency error

(1) (2)

= –20 °C to 70 °C –2.5% 0.25% 2.5%T

= –40 °C to 85 °C –4.0% 0.25% 4.0%t

LSXO

Start-up time

(3)

500 μs

(1) The frequency drift is included and measured from the trimmed frequency at V

= 2.5V, T

= 25 °C.(2) The frequency error is measured from 32.768 kHz.(3) The startup time is defined as the time it takes for the oscillator output frequency to be ±3%.

= –40 °C to 85 °C, 2.4 V < V

< 2.6 V; Typical Values at T

= 25 °C and V

= 2.5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

SR_IN

Input voltage range, V

(SRN)

and V

(SRP)

= V

(SRN)

– V

(SRP)

–0.125 0.125 Vt

SR_CONV

Conversion time Single conversion 1 sResolution 14 15 bitsBefore calibration 1 mVV

SR_OS

Input offset

After calibration 10 μVINL Integral nonlinearity error ±0.007 ±0.034 % FSRZ

SR_IN

Effective input resistance

(1)

2.5 M ΩI

SR_LKG

Input leakage current

(1)

0.3 μA

(1) Specified by design. Not tested in production.

= –40 °C to 85 °C, 2.4 V < V

< 2.6 V; Typical Values at T

= 25 °C and V

= 2.5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

ADC_IN

Input voltage range –0.2 1 V

Submit Documentation Feedback ELECTRICAL SPECIFICATIONS 5

www.ti.com

3.9 DATA FLASH MEMORY CHARACTERISTICS

3.10 I

C-COMPATIBLE INTERFACE COMMUNICATION TIMING CHARACTERISTICS

bq27500

bq27501

System-Side Impedance Track™ Fuel Gauge

SLUS785 – SEPTEMBER 2007

ADC (TEMPERATURE AND CELL MEASUREMENT) CHARACTERISTICS (continued)

= –40 °C to 85 °C, 2.4 V < V

< 2.6 V; Typical Values at T

= 25 °C and V

= 2.5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

ADC_CONV

Conversion time 125 msResolution 14 15 bitsV

ADC_OS

Input offset 1 mVZ

ADC1

Effective input resistance (TS, RID 8 M Ω[bq27501 only])

bq27500/1 not measuring cell voltage 8 M ΩZ

ADC2

Effective input resistance (BAT)

(1)

bq27500/1 measuging cell voltage 100 k ΩI

ADC_LKG

Input Leakage Current

(1)

0.3 μA

(1) Specified by design. Not tested in production.

= –40 °C to 85 °C, 2.4 V < V

< 2.6 V; Typical Values at T

= 25 °C and V

= 2.5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

Data retention See

(1)

YearsFlash programming write-cycles See

(1)

20,000 Cyclest

WORDPROG

Word programming time See

(1)

2 msI

CCPROG

Flash-write supply current 5 10 mA

(1) Specified by design. Not production tested

= –40 °C to 85 °C, 2.4 V < V

< 2.6 V; Typical Values at T

= 25 °C and V

= 2.5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

SCL/SDA rise time 1 μst

SCL/SDA fall time 300 nst

w(H)

SCL pulse width (high) 4 μst

w(L)

SCL pulse width (low) 4.7 μst

su(STA)

Setup for repeated start 4.7 μst

d(STA)

Start to first falling edge of SCL 4 μst

su(DAT)

Data setup time 250 nsReceive mode 0t

h(DAT)

Data hold time nsTransmit mode 300t

su(STOP)

Setup time for stop 4 μst

BUF

Bus free time between stop and start 4.7 μsf

SCL

Clock frequency 10 100 kHzt

BUSERR

Bus error timeout 17.3 21.2 s

ELECTRICAL SPECIFICATIONS6Submit Documentation Feedback

www.ti.com

bq27500

bq27501System-Side Impedance Track™ Fuel Gauge

SLUS785 – SEPTEMBER 2007

Figure 3-1. I

C-Compatible Interface Timing Diagrams

Submit Documentation Feedback ELECTRICAL SPECIFICATIONS 7

www.ti.com

4 GENERAL DESCRIPTION

bq27500

bq27501

System-Side Impedance Track™ Fuel Gauge

SLUS785 – SEPTEMBER 2007

The bq27500/1 accurately predicts the battery capacity and other operational characteristics of a singleLi-based rechargeable cell. It can be interrogated by a system processor to provide cell information, suchas State-of-Charge (SOC), Time-to-Empty (TTE) and Time-to-Full (TTF).

Information is accessed through a series of commands, called Standard Commands. Further capabilitiesare provided by the additional Extended Commands set. Both sets of commands, indicated by the generalformat Command( ), are used to read and write information contained within the bq27500/1 control andstatus registers, as well as its data flash locations. Commands are sent from system to gauge using thebq27500/1’s I

C serial communications engine, and can be executed during application development,pack manufacture, or end-equipment operation.

Cell information is stored in the bq27500/1 in non-volatile flash memory. Many of these data flashlocations are accessible during application development. They cannot be accessed directly duringend-equipment operation. Access to these locations is achieved by either use of the bq27500/1'scompanion evaluation software, through individual commands, or through a sequence of data-flash-accesscommands. To access a desired data flash location, the correct data flash subclass and offset must beknown.

The bq27500/1 provides 96 bytes of user-programmable data flash memory, partitioned into 3 32-byteblocks: Manufacturer Info Block A,Manufacturer Info Block B, and Manufacturer Info Block C. Thisdata space is accessed through a data flash interface. For specifics on accessing the data flash, seeSection 4.3 Manufacturer Information Blocks.

The key to the bq27500/1’s high-accuracy gas gauging prediction is Texas Instrument’s proprietaryImpedance Track™ algorithm. This algorithm uses cell measurements, characteristics, and properties tocreate state-of-charge predictions that can achieve less than 1% error across a wide variety of operatingconditions and over the lifetime of the battery.

The bq27500/1 measures charge/discharge activity by monitoring the voltage across a small-value seriessense resistor (5 m Ωto 20 m Ωtyp.) located between the system's Vss and the battery’s PACK– terminal.When a cell is attached to the bq27500/1, cell impedance is computed, based on cell current, cell OpenCircuit Voltage (OCV), and cell voltage under loading conditions.

The bq27500/1 can use an NTC thermistor (default is Semitec 103AT) for temperature measurement, orcan also be configured to use its internal temperature sensor. The bq27500/1 uses temperature to monitorthe battery-pack environment, which is used for fuel gauging and cell protection functionality.

To minimize power consumption, the bq27500/1 has several power modes: NORMAL, SLEEP,HIBERNATE, and BAT INSERT CHECK. The bq27500/1 passes automatically between these modes,depending upon the occurrence of specific events, though a system processor can initiate some of thesemodes directly. More details can be found in the Section 5.7 POWER MODES.

NOTE

FORMATTING CONVENTIONS IN THIS DOCUMENT:

Commands: italics with parentheses and no breaking spaces, e.g. RemainingCapacity( ).

Data Flash: italics,bold, and breaking spaces, e.g. Design Capacity

Data Flash Bits: italics and bold, e.g: [LED1]

Modes and states: ALL CAPITALS, e.g. UNSEALED mode.

8GENERAL DESCRIPTION Submit Documentation Feedback

www.ti.com

4.1 DATA COMMANDS

4.1.1 STANDARD DATA COMMANDS

bq27500

bq27501System-Side Impedance Track™ Fuel Gauge

SLUS785 – SEPTEMBER 2007

The bq27500/1 uses a series of 2-byte standard commands to enable system reading and writing ofbattery information. Each standard command has an associated command-code pair, as indicated inTable 4-1 . Because each command consists of two bytes of data, two consecutive I

C transmissions mustbe executed both to initiate the command function, and to read or write the corresponding two bytes ofdata. Additional options for transferring data, such as spooling, are described in Section 7.1 I

CINTERFACE. Standard commands are accessible in NORMAL operation. Read/Write permissions dependon the active access mode, SEALED or UNSEALED (for details on the SEALED and UNSEALED states,see Section 4.4 Access Modes).

Table 4-1. Standard Commands

COMMAND SEALED UNSEALEDNAME UNITSCODE ACCESS ACCESS

Control( ) CNTL 0x00 / 0x01 N/A R/W R/WAtRate( ) AR 0x02 / 0x03 mA R/W R/WAtRateTimeToEmpty( ) ARTTE 0x04 / 0x05 Minutes R RTemperature( ) TEMP 0x06 / 0x07 0.1 °K R RVoltage( ) VOLT 0x08 / 0x09 mV R RFlags( ) FLAGS 0x0a / 0x0b N/A R RNominalAvailableCapacity( ) NAC 0x0c / 0x0d mAh R RFullAvailableCapacity( ) FAC 0x0e / 0x0f mAh R RRemainingCapacity( ) RM 0x10 / 0x11 mAh R RFullChargeCapacity( ) FCC 0x12 / 0x13 mAh R RAverageCurrent( ) AI 0x14 / 0x15 mA R RTimeToEmpty( ) TTE 0x16 / 0x17 Minutes R RTimeToFull( ) TTF 0x18 / 0x19 Minutes R RStandbyCurrent( ) SI 0x1a / 0x1b mA R RStandbyTimeToEmpty( ) STTE 0x1c / 0x1d Minutes R RMaxLoadCurrent( ) MLI 0x1e / 0x1f mA R RMaxLoadTimeToEmpty( ) MLTTE 0x20 / 0x21 Minutes R RAvailableEnergy( ) AE 0x22 / 0x23 10mWhr R RAveragePower( ) AP 0x24 / 0x25 10mW R RTimeToEmptyAtConstantPower( ) TTECP 0x26 / 0x27 Minutes R RReserved RSVD 0x28 / 0x29 N/A R RCycleCount( ) CC 0x2a / 0x2b Counts R RStateOfCharge( ) SOC 0x2c / 0x2d % R R

Submit Documentation Feedback GENERAL DESCRIPTION 9

www.ti.com

bq27500

bq27501

System-Side Impedance Track™ Fuel Gauge

SLUS785 – SEPTEMBER 2007

4.1.1.1 Control( ): 0x00/0x01

Issuing a Control( ) command requires a subsequent two-byte sub-command. These additional bytesspecify the particular control function desired. The Control( ) command allows the system to controlspecific features of the bq27500 during normal operation and additional features when the bq27500/1 is indifferent access modes, as described in Table 4-2 .

Table 4-2. Control( ) Subcommands

CNTL SEALEDCNTL FUNCTION DESCRIPTIONDATA ACCESS

CONTROL STATUS 0x0000 Yes Reports the status of DF Checksum, Hibernate, IT, etc.DEVICE TYPE 0x0001 Yes Reports the device type (eg: "bq27500")FW VERSION 0x0002 Yes Reports the firmware version on the device typeHW VERSION 0x0003 Yes Reports the hardware version of the device typeReserved 0x0004 No Not to be usedRESET DATA 0x0005 No Returns reset dataReserved 0x0006 No Not to be usedPREV_MACWRITE 0x0007 No Returns previous MAC command codeReports the chemical identifier of the Impedance Track™CHEMID 0x0008 Yes

configurationBOARD OFFSET 0x0009 No Forces the device Board Offset to be measured and storedCC INT OFFSET 0x000b No Forces the device to measure and store the internal CC offsetSET HIBERNATE 0x0011 Yes Forces DF:Pack Configuration [HIBERNATE] to 1CLEAR HIBERNATE 0x0012 Yes Forces DF:Pack Configuration [HIBERNATE] to 0SEALED 0x0020 No Places the bq27500/1 in SEALED access modeIT ENABLE 0x0021 No Enables the Impedance Track™ algorithmIFCHECKSUM 0x0022 No Reports the instruction flash checksumCALMODE 0x0040 No Places the bq27500/1 in calibration modeRESET 0x0041 No Forces a full reset of the bq27500/1

4.1.1.1.1 CONTROL STATUS: 0X0000

Instructs the gas gauge to return status information to Control addresses 0x00/0x01. The status wordincludes the following information.

Table 4-3. CONTROL STATUS Bit Definitions

Flags( ) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0

High Byte – FAS SS - CCA BCA – –Low Byte – HIBERNATE – SLEEP LDMD RUP_DIS VOK QEN

FAS = Status bit indicating the bq27500/1 is in FULL ACCESS SEALED state. Active when set.SS = Status bit indicating the bq27500/1 is in SEALED State. Active when set.CCA = Status bit indicating the bq27500/1 is Coulomb Counter Calibration routine is active. Active when set.BCA = Status bit indicating the bq27500/1 Board Calibration routine is active. Active when set.HIBERNATE = Status bit indicating a request for entry into HIBERNATE from SLEEP mode. True when set. Default is 0.SLEEP = Status bit indicating the bq27500/1 is in SLEEP mode. True when set. Default is 0.LDMD = Status bit indicating the bq27500/1 Impedance Track™ algorithm is using constant-power mode. True when set. Default is 0(constant-current mode)RUP_DIS = Status bit indicating the bq27500/1 Ra table updates are disabled. Updates disabled when set.VOK = Status bit indicating the bq27500/1 voltages are OK for QMAX. True when set.QEN = Status bit indicating the bq27500/1 QMAX updates enabled. True when set.

4.1.1.1.2 DEVICE TYPE: 0x0001

Instructs the fuel gauge to return the device type to addresses 0x00/0x01.

GENERAL DESCRIPTION10 Submit Documentation Feedback

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Texas Instruments Matériel informatique

Texas Instruments

Texas Instruments TMS320C6000 DSP Manuel utilisateur

Texas Instruments

Texas Instruments MSP-EXP430F5438 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320C67X+ DSP Manuel utilisateur

Texas Instruments

Texas Instruments INA234EVM Manuel utilisateur

Texas Instruments

Texas Instruments CapTIvate Touch Manuel de la liste des pièces

Texas Instruments

Texas Instruments TPS65941515-Q1 Manuel utilisateur

Texas Instruments

Texas Instruments AM1808 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320C6711D Manuel utilisateur

Texas Instruments

Texas Instruments TMS320C6201 Manuel utilisateur

Texas Instruments

Texas Instruments Tiva TM4C123G Manuel utilisateur

Texas Instruments

Texas Instruments bq50002 Manuel utilisateur

Texas Instruments

Texas Instruments OMAP5910 Manuel utilisateur

Texas Instruments

Texas Instruments OMAP35 Series Manuel utilisateur

Texas Instruments

Texas Instruments 2000 series Manuel utilisateur

Texas Instruments

Texas Instruments DRV603EVM Manuel utilisateur

Texas Instruments

Texas Instruments DRV8811EVM Manuel utilisateur

Texas Instruments

Texas Instruments BQ25185EVM Manuel utilisateur

Texas Instruments

Texas Instruments OMAP5912 Manuel utilisateur

Texas Instruments

Texas Instruments TPS25762Q1EVM-146 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320C6457 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320DM355 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320C642x DSP Manuel utilisateur

Texas Instruments

Texas Instruments LM38020QEVM Manuel utilisateur

Texas Instruments

Texas Instruments TPA6135A2 EVM Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur