Texas Instruments TPS7H4003EVM Manuel utilisateur

User's Guide

TPS7H4003EVM Evaluation Module (EVM)

ABSTRACT

The TPS7H4003EVM is the evaluation module (EVM) for the TPS7H4003-SEP and provides a platform to

electrically evaluate its features. This user's guide provides details about the EVM, its configuration, schematics,

and BOM.

Figure 1-1. TPS7H4003EVM (Single Channel)

Table of Contents

1 TPS7H4003EVM Overview..................................................................................................................................................... 3

2 TPS7H4003EVM Default Configuration.................................................................................................................................4

3 TPS7H4003EVM Initial Setup................................................................................................................................................. 5

4 TPS7H4003EVM Testing......................................................................................................................................................... 6

5 TPS7H4003EVM Schematic................................................................................................................................................. 10

6 TPS7H4003EVM Bill of Materials (BOM)............................................................................................................................. 11

7 Board Layout.........................................................................................................................................................................14

8 Support Resources...............................................................................................................................................................20

9 Revision History................................................................................................................................................................... 20

List of Figures

Figure 1-1. TPS7H4003EVM (Single Channel)........................................................................................................................... 1

Figure 4-1. Output Voltage Regulation........................................................................................................................................ 6

Figure 4-2. Output Voltage Ripple VIN = 5 V, VOUT = 1 V, IOUT = 18 A.................................................................................... 6

Figure 4-3. Output Soft Start Voltage, VIN = 5 V, VOUT = 1 V, IOUT = 18 A.............................................................................. 7

Figure 4-4. Transient Response to Load Step 9 A to 18 A at 1 A/µs........................................................................................... 7

Figure 4-5. Transient Response to Load Step 18 A to 9 A at 1 A/µs........................................................................................... 8

Figure 4-6. EVM Modification to Measure Frequency Response................................................................................................ 8

Figure 4-7. Frequency Response Test Setup.............................................................................................................................. 9

www.ti.com Table of Contents

SLVUC73A – JANUARY 2022 – REVISED AUGUST 2023

Submit Document Feedback

TPS7H4003EVM Evaluation Module (EVM) 1

Figure 4-8. Frequency Response................................................................................................................................................ 9

Figure 5-1. TPS7H4003EVM Schematic................................................................................................................................... 10

Figure 7-1. Top Overlay............................................................................................................................................................. 14

Figure 7-2. Top Solder............................................................................................................................................................... 14

Figure 7-3. Top Layer.................................................................................................................................................................15

Figure 7-4. Signal Layer One.....................................................................................................................................................15

Figure 7-5. Signal Layer Two.....................................................................................................................................................16

Figure 7-6. Signal Layer Three.................................................................................................................................................. 16

Figure 7-7. Signal Layer Four.................................................................................................................................................... 17

Figure 7-8. Signal Layer Five.....................................................................................................................................................17

Figure 7-9. Signal Layer Six...................................................................................................................................................... 18

Figure 7-10. Bottom Layer......................................................................................................................................................... 18

Figure 7-11. Bottom Solder........................................................................................................................................................ 19

Figure 7-12. Bottom Overlay......................................................................................................................................................19

Figure 7-13. Drill Drawing.......................................................................................................................................................... 20

Figure 7-14. PCB Dimensions................................................................................................................................................... 20

List of Tables

Table 2-1. Default EVM Configuration......................................................................................................................................... 4

Table 3-1. Summary of Connections............................................................................................................................................5

Table 6-1. TPS7H4003EVM BOM..............................................................................................................................................11

Trademarks

TI E2E™ is a trademark of Texas Instruments.

All trademarks are the property of their respective owners.

Trademarks www.ti.com

2TPS7H4003EVM Evaluation Module (EVM) SLVUC73A – JANUARY 2022 – REVISED AUGUST 2023

Submit Document Feedback

1 TPS7H4003EVM Overview

The TPS7H4003-SEP is a radiation hardened, 7-V, 18-A synchronous step-down converter with integrated high-

side and low-side MOSFETs. High efficiency and efficient usage of space are achieved through low resistance

MOSFETs and a current mode control implementation.

The EVM is configured in a default state to accept a 5-V input but can be modified to disable or change the

under voltage lock out (UVLO) protection, allowing for any input voltage from 3 V to 7 V. The EVM is also

configured for a 1-V output at a maximum peak output current of 18 A. Again, the regulated output voltage can

be modified by changing one resistor on the board. The TSP7H4003-SEP has a dedicated soft start, enable, and

adjustable slope compensation pins providing design flexibility to meet specific application requirements.

Finally, as shown in Figure 1-1, this EVM supports a single POL channel. However, the device does support

parallel operation. With four POLs operating in quadrature phases, a 72-A load current can theoretically be

provided.

1.1 Features

• 0.6-V ±1.6% voltage reference over temperature, radiation, and line and load regulation

• Adjustable slope compensation

• Adjustable soft start

• Adjustable input enable and undervoltage lockout (UVLO)

• Maximum output current of 18 A

1.2 Applications

• Point of load regulation

• Supports harsh environment applications

• Space satellite point of load supply for FPGAs, microcontrollers, data converters, and ASICs

• Space satellite payloads

• Radiation hardened applications

www.ti.com TPS7H4003EVM Overview

SLVUC73A – JANUARY 2022 – REVISED AUGUST 2023

Submit Document Feedback

TPS7H4003EVM Evaluation Module (EVM) 3

2 TPS7H4003EVM Default Configuration

Table 2-1 describes the default configuration of the TPS7H4003EVM listing the external components that define

the converter design.

Table 2-1. Default EVM Configuration

PARAMETER SPECIFICATIONS DESCRIPTION

Input power supply 5 V Bound by UVLO enable circuit (R9, R10)

Regulated output voltage 1 V R6 (RTOP) = 10 kΩ, R7 (RBOTTOM) = 15.4 kΩ

LOUT 1.0 µH Chosen to meet inductor ripple current of 10% (Kind = 0.1)

COUT 2 mF

Chosen for (1) ESR = 1 mΩ to set output voltage ripple; (2)

value used during single event effects testing ensuring regulation

maintained with single event upset to switching

Output current 0 to 18 A By design

Switching frequency 500 kHz Set by R1 (RT) = 174 kΩ

Soft start time constant ≈2 ms Set by C16 (Css) = 10 nF

UVLO enable rising ≈4.432 V Set by R10 = 10 kΩ and R9 = 3.4 kΩ

UVLO enable falling ≈4.284 V Set by R10 = 10 kΩ and R9 = 3.4 kΩ

Loop bandwidth ≈30 kHz Set by operational transconductance amplifier (OTA) compensation

circuit: R7 (RCOMP) = 10 kΩ, C15 (CCOMP) = 10 nF, C14 (CHF) =

150 pF

Loop phase margin ≈60°

Gain margin ≈–25 dB

TPS7H4003EVM Default Configuration www.ti.com

4TPS7H4003EVM Evaluation Module (EVM) SLVUC73A – JANUARY 2022 – REVISED AUGUST 2023

Submit Document Feedback

3 TPS7H4003EVM Initial Setup

This section provides the test instruments required and the connections to the EVM.

1. Input DC power supply

a. Set for 5-V DC, 8-A current limit.

b. Connect positive output of DC supply to pin 1 of connector J1 (PVIN) and negative terminal of supply to

pin 2 of connector J1 for ground using 16 AWG wire or larger.

• NOTE: For more precise measurements, eliminating the IR voltage drop in the input cables is

achieved by using a power supply source with sensing ports and connecting between TP2 to PVIN

and TP1 to GND.

2. DC electronic load

a. Connect positive DC input of e-load to pin 1, VOUT, of connector J7 (VOUT) using 16 AWG wire.

• NOTE: Wire from pin 1, positive terminal of connector, to the e-load should include at least some part

in which the wire gauge can be strapped by the oscilloscope current probe. This will eliminate the

need for a setup change to cover all tests.

b. Connect negative DC input of e-load to pin 2, PGND, of connector J7 (VOUT) using 16 AWG wire.

c. Connect voltage monitoring sensing ports of e-load across test points TP12 (VOUT1) and TP13 (PGND).

A voltage meter can be used to monitor this voltage also.

3. Oscilloscope

a. CH1 - Connect voltage scope probe to scope probe test point J5 (PH) to monitor the phase node. DC

coupled, Full BW, 2 V/div, Rising Edge Trigger at 0.5 V.

b. CH2 - Connect voltage scope probe to scope probe test point J6 (VOUT) to monitor the output voltage.

AC coupled, BW = 20 MHz, 10 mV/div.

c. CH4 - Connect current scope probe to monitor current through wire connecting J7 (VOUT) and e-load. 5

A/div.

• NOTE: Only required for transient load testing.

Table 3-1. Summary of Connections

REFERENCE DESIGNATOR SILKSCREEN FUNCTION

J1 PVIN Input power: pin 1 = 5 V, pin 2 = GND (Vsupply)

J7 VOUT Output voltage: pin 2 = GND, pin 1 = Vout ≈1 V (e-load)

J5 PH Phase switching node scope probe test point (Scope CH-1)

J6 VOUT VOUT scope probe test point (Scope CH-2)

TP12 VOUT VOUT test point (e-load monitor)

TP2 PVIN PVIN test point (Vsupply_sense)

TP1, TP13 GND GND test points (Vsupply_sense, e-load monitor)

www.ti.com TPS7H4003EVM Initial Setup

SLVUC73A – JANUARY 2022 – REVISED AUGUST 2023

Submit Document Feedback

TPS7H4003EVM Evaluation Module (EVM) 5

4 TPS7H4003EVM Testing

The following tests will be described in subsequent sections.

•Section 4.1 Output voltage regulation

•Section 4.2 Output voltage ripple

•Section 4.3 Soft startup

•Section 4.4 Transient response to positive/negative load step (9 A to 18 A to 9 A)

•Section 4.5 Loop frequency response

4.1 Output Voltage Regulation

1. Turn-on input DC source (5 V).

2. Turn on the e-load and sweep load current from 0 A to 18 A. The monitored output voltage at TP12 (VOUT)

is at or near 1.0 V across the entire current load sweep as shown in Figure 4-1.

Figure 4-1. Output Voltage Regulation

4.2 Output Voltage Ripple

Display CH1 (PH) and CH2 (VOUT) [AC coupled, BW = 20 MHz] on oscilloscope to monitor the switching phase

node and the output voltage ripple as shown in Figure 4-2.

Figure 4-2. Output Voltage Ripple VIN = 5 V, VOUT = 1 V, IOUT = 18 A

TPS7H4003EVM Testing www.ti.com

6TPS7H4003EVM Evaluation Module (EVM) SLVUC73A – JANUARY 2022 – REVISED AUGUST 2023

Submit Document Feedback

4.3 Soft Startup

Display CH1 (PH) and CH2 (VOUT) [DC coupled, 500 mV/div] on oscilloscope to monitor the switching phase

and the soft start profile of the output voltage as shown in Figure 4-3.

Figure 4-3. Output Soft Start Voltage, VIN = 5 V, VOUT = 1 V, IOUT = 18 A

4.4 Transient Response to Positive/Negative Load Step (9 A to 18 A to 9 A)

1. Configure e-load to switch between 9 A and 18 A at a rate of 1 A/µs.

2. On oscilloscope, display CH2 (VOUT) [AC coupled, 20 mV/div] and CH4 (Output Current Probe) [5 A/div,

trigger rising edge ≈12 A] with 40 µs/div.

Figure 4-4 shows the response to this load step to be less than 35 mV or –3.5%.

Figure 4-4. Transient Response to Load Step 9 A to 18 A at 1 A/µs

www.ti.com TPS7H4003EVM Testing

SLVUC73A – JANUARY 2022 – REVISED AUGUST 2023

Submit Document Feedback

TPS7H4003EVM Evaluation Module (EVM) 7

3. Change the trigger on CH4 to falling edge to capture the transient response of VOUT to negative current

step from 18 A to 9 A as shown in Figure 4-5.

Figure 4-5. Transient Response to Load Step 18 A to 9 A at 1 A/µs

4.5 Loop Frequency Response

Measuring the frequency response of the feedback loop requires a unique test setup as well as physical

changes to the EVM. 0-Ω resistor jumper R8, below TP9 (BODE) test point and circled in yellow in the graphic

below, must be lifted in order to break the loop. Both test points TP9 (BODE) and TP10 (VOUT) will be used for

connections to the Bode100 instruments.

Figure 4-6. EVM Modification to Measure Frequency Response

TPS7H4003EVM Testing www.ti.com

8TPS7H4003EVM Evaluation Module (EVM) SLVUC73A – JANUARY 2022 – REVISED AUGUST 2023

Submit Document Feedback

4.6 Setup

The test setup, which includes several connections to Picotest Bode100 test instruments, is shown in Figure 4-7

with measurement results shown in Figure 4-8. The CHF, high frequency pole, component of the compensation

circuit is optional. Omitting it will result in slightly increased phase margin. However, the benefit of including it is

that the gain curve is set in a downward trajectory as frequency increases, making a monotonic gain curve more

likely to be achieved.

Figure 4-7. Frequency Response Test Setup

Figure 4-8. Frequency Response

www.ti.com TPS7H4003EVM Testing

SLVUC73A – JANUARY 2022 – REVISED AUGUST 2023

Submit Document Feedback

TPS7H4003EVM Evaluation Module (EVM) 9

5 TPS7H4003EVM Schematic

Figure 5-1. TPS7H4003EVM Schematic

TPS7H4003EVM Schematic www.ti.com

10 TPS7H4003EVM Evaluation Module (EVM) SLVUC73A – JANUARY 2022 – REVISED AUGUST 2023

Submit Document Feedback

Table des matières

Autres manuels Texas Instruments Matériel informatique

Texas Instruments

Texas Instruments TPS65910 EVM Manuel utilisateur

Texas Instruments

Texas Instruments ADS8365MEVM Manuel utilisateur

Texas Instruments

Texas Instruments TMS320C55 Series Manuel utilisateur

Texas Instruments

Texas Instruments CC1101DK Manuel utilisateur

Texas Instruments

Texas Instruments BQ25638 Series Manuel utilisateur

Texas Instruments

Texas Instruments TMS320C642x DSP Manuel utilisateur

Texas Instruments

Texas Instruments PCI7620 Manuel utilisateur

Texas Instruments

Texas Instruments BoosterPack BOOSTXL-ADS7142-Q1 Manuel utilisateur

Texas Instruments

Texas Instruments TMS320VC5509 Guide d'installation et d'utilisation

Texas Instruments

Texas Instruments LM97937EVM R2 Manuel utilisateur

Texas Instruments

Texas Instruments SimpleLink CC3200 Wi-Fi Manuel utilisateur

Texas Instruments

Texas Instruments OMAP-L137 EVM Manuel utilisateur

Texas Instruments

Texas Instruments TUSB2E11 Manuel utilisateur

Texas Instruments

Texas Instruments MCT8317 Manuel utilisateur

Texas Instruments

Texas Instruments MSPM0 Manuel utilisateur

Texas Instruments

Texas Instruments C2000 Piccolo LaunchPad Manuel utilisateur

Texas Instruments

Texas Instruments TPS7A15 Manuel utilisateur

Texas Instruments

Texas Instruments LMH0318 Manuel

Texas Instruments

Texas Instruments PGA450Q1EVM Manuel utilisateur

Texas Instruments

Texas Instruments DS90UH927Q Manuel utilisateur

Texas Instruments

Texas Instruments TMS320C6457 Manuel utilisateur

Texas Instruments

Texas Instruments KCU105 Manuel utilisateur

Texas Instruments

Texas Instruments INA234EVM Manuel utilisateur

Texas Instruments

Texas Instruments DS250DF810EVM Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur