Texas Instruments DRV8811EVM Manuel utilisateur
DRV8811EVM
User's Guide
Literature Number: SLVA344AJuly 2009 – Revised September 2009
2 SLVA344A – July 2009 – Revised September 2009Submit Documentation Feedback
Contents
1 Introduction ......................................................................................................................... 61.1 Block Diagram ............................................................................................................. 61.2 Power Connectors ........................................................................................................ 61.3 Test Stakes ................................................................................................................ 71.4 Jumpers .................................................................................................................... 71.5 Motor Outputs ............................................................................................................. 72 Installing Drivers And Software ............................................................................................. 72.1 Installing the FTDI USB Driver .......................................................................................... 72.2 Installing the DRV8811 Evaluation Board Windows Application Software ........................................ 82.3 Running the Windows Application Software ........................................................................... 83 Windows Application ............................................................................................................ 83.1 Menu ........................................................................................................................ 93.2 DRV8811 GPIO Control Signals ........................................................................................ 93.3 Updating DAC Output for Current Control (VREF/DECAY) ........................................................ 103.4 Updating DAC Output for Decay Control (DECAY) ................................................................. 103.5 Operating the Stepper Motor ........................................................................................... 104 Schematic ......................................................................................................................... 12
SLVA344A – July 2009 – Revised September 2009 Table of Contents 3Submit Documentation Feedback
www.ti.com
List of Figures
1 VREF SELECT Jumper ..................................................................................................... 72 DECAY SELECT Jumper ................................................................................................... 73 DRV8811_RD_EVM_R1p0.exe Main Screen ............................................................................ 84 Acknowledgement Text Box ................................................................................................ 95 Signals Frame ................................................................................................................ 96 Curent Control Frame ...................................................................................................... 107 Current Control Frame ..................................................................................................... 108 Step Rate ................................................................................................................... 119 Speed Control Frame ...................................................................................................... 1110 Step Control Frame ........................................................................................................ 12
4List of Figures SLVA344A – July 2009 – Revised September 2009Submit Documentation Feedback
User's GuideSLVA344A – July 2009 – Revised September 2009
Laser and Motor Drives
This document is provided as a supplement to the DRV8811 datasheet. It details the hardwareimplementation of the DRV8811 customer evaluation module (EVM).
SLVA344A – July 2009 – Revised September 2009 Laser and Motor Drives 5Submit Documentation Feedback
1 Introduction
1.1 Block Diagram
VM Power
Test Stakes
DRV8811
Motor Outputs
MSP430F1612USB
1.2 Power Connectors
Introduction
www.ti.com
The DRV8811_RD customer EVM is the complete solution to evaluating the DRV8811 microsteppingbipolar stepper driver. It houses a USB link to provide easy control from a PC computer, an MSP430microcontroller that interprets serial commands from the PC and generates control signals to the driverdevice, and the DRV8811 device with access to all signals for a complete evaluation.
The DRV8811 customer EVM uses a combination of terminal blocks and test clips for theapplication/monitoring of power. The only power rail the user must supply is VM for the device’s powerstage. VDD for logic levels is internally generated from the USB connection.
The user must apply VM according to datasheet recommended parameters.
Laser and Motor Drives6 SLVA344A – July 2009 – Revised September 2009Submit Documentation Feedback
1.3 Test Stakes
1.4 Jumpers
1.4.1 VREF SELECT (JP1) Jumper
(a) (b)
POT
INT
POT
INT
1.4.2 DECAY SELECT (JP6) Jumper
(a) (b)
POT
INT
POT
INT
1.5 Motor Outputs
2 Installing Drivers And Software
2.1 Installing the FTDI USB Driver
www.ti.com
Installing Drivers And Software
Every pin on the device has been brought out to a test stake. A label on the silkscreen identifies eachsignal.
Three pin jumpers can be configured independently from the other two or three pin jumpers. However, twopin jumpers must either be closed or open. Two pin jumpers (JP2 to JP5) connect the diodes to the motoroutputs and are used under asynchronous rectification (SR = LO).
Figure 1. VREF SELECT Jumper
To configure the VREF SELECT jumper: Figure 1 (a) selects an analog voltage derived from VDD througha voltage divider implemented as a potentiometer R4. Figure 1 (b) selects an analog voltage derived fromthe MSP430’s digital to analog converter channel 0 (DAC0).
Figure 2. DECAY SELECT Jumper
To configure the DECAY SELECT jumper: Figure 2 (a) selects an analog voltage derived from VDDthrough a voltage divider implemented as a potentiometer R6. Figure 2 (b) selects an analog voltagederived from the MSP430’s digital to analog converter channel 1 (DAC1).
There are three ways of connecting the bipolar stepper motor into the DRV8811 EVM: four pin header(J2), four position terminal block (J3) or test clips. Each connection style offers identical connectivity to thedevice’s output terminals. It is recommended, however, to use the header or terminal block, as the teststakes traces are of low current handling capability.
Instructions on how to install the FTDI USB driver on a Windows based computer are detailed in the“USB_Drivers_Install_Readme.pdf” file supplied with the CD inside the USB_Driver folder.
SLVA344A – July 2009 – Revised September 2009 Laser and Motor Drives 7Submit Documentation Feedback
2.2 Installing the DRV8811 Evaluation Board Windows Application Software
2.3 Running the Windows Application Software
3 Windows Application
Windows Application
www.ti.com
The included CD contains a folder titled “Windows Application”. It is recommended for the contents of thisfolder to be copied to any desired folder on the computer. The reason for this is the Settings.ini file will bewritten upon software exit. This action can not take place if the application is run within the CDenvironment.
To run the application, double click the DRV8811_RD_EVM_R1p0.exe application icon found in the samefolder the application was extracted into.
The DRV8811 Windows Application is the software counterpart for the DRV8811 EVM. It is in charge ofconnecting to the MSP430 microcontroller via a USB connection which in turn selects the proper logicstate for the DRV8811 control signals.
The graphical user interface (GUI) has been designed to allow for all of the DRV8811 device’sfunctionality to be tested without having to intervene with the hardware, except for the proper configurationof jumpers when needed.
Figure 3 shows the DRV8811_RD_EVM_R1p0.exe main screen. It contains menu items to configure andenable/disable the serial port, frames with GPIO control for the DRV8811 control signals, stepper motorcontrol for start/stop and speed, and current/decay control through the MSP430 DACs.
Figure 3. DRV8811_RD_EVM_R1p0.exe Main Screen
Laser and Motor Drives8 SLVA344A – July 2009 – Revised September 2009Submit Documentation Feedback
3.1 Menu
3.2 DRV8811 GPIO Control Signals
www.ti.com
Windows Application
The menu at the top of the application offers a series of quick options for how the COM port is to behave.1. File →Exit - Terminates the application2. Settings →Port - Selects from COM1 to COM4. Default is COM4.The serial port's actual port number defaults to what we have specified on“USB_Drivers_Install_Readme.pdf”. However, any port between COM 1 and COM 4 are equallyusable.
3. Connect: Opens the serial port. When this menu item is pressed, its caption changes to “Disconnect”.4. Disconnect: Closes the serial port. When this menu item is pressed, its caption changes to “Connect”.
After opening the application, the order of events should be:1. Go to Settings →Port and choose the COM port where the USB virtual COM port device has beenconfigured to work. If the COM port is 4, then this step can be skipped as application defaults toCOM4.
2. Press Connect. If the port is available, the menu changes the “Connect“ caption to “Disconnect“. PressDisconnect to disable the serial communications.
< 1> < 4> < 0> should return on the text box as an acknowledgement. The text box also changes from red togreen, as shown in Figure 4 .
Figure 4. Acknowledgement Text Box
The application is ready for use.
Once the application is communicating with the interface board, the control signals can be actuated bychecking or un-checking check boxes on the Signals frame.
Figure 5. Signals Frame
SLVA344A – July 2009 – Revised September 2009 Laser and Motor Drives 9Submit Documentation Feedback
3.3 Updating DAC Output for Current Control (VREF/DECAY)
VREF = DAC_VALUE ·
2.5 V
¾
4095
(1)
3.4 Updating DAC Output for Decay Control (DECAY)
DECAY = DAC_VALUE ·
2.5 V
¾
4095
(2)
3.5 Operating the Stepper Motor
3.5.1 Turning the Stepper Motor
Windows Application
www.ti.com
A checked checkbox translates to a HI level on the respective control signal. A un-checked checkboxtranslates to a LO level on the respective control signal.
If the DRV8811 EVM has been configured to accept VREF analog voltages through the MSP430microcontroller interface (JP1 is set to INT), then the slider bar on the Current Control frame can be usedto set the VREF voltage.
Figure 6. Curent Control Frame
The MSP430F1612 12-bit DAC channel 0 is connected to the DRV8811 VREF analog input. Changing theDAC digital value from 0 to 4095, changes the analog voltage at the VREF/DECAY pin from 0 V to 2.5 Vrespectively. See Equation 1 .
Where VREF is the output voltage and DAC_VALUE is a number from 0 to 4095.
If the DRV8811 EVM has been configured to accept DECAY analog voltages through the MSP430microcontroller interface (JP6 is set to INT), then the slider bar on the Current Control frame can be usedto set the DECAY voltage.
Figure 7. Current Control Frame
The MSP430F1612 12 bit DAC channel 1 is connected to the DRV8811 DECAY analog input. Changingthe DAC digital value from 0 to 4095, changes the analog voltage at the DECAY pin from 0 V to 2.5 Vrespectively. See Equation 2 .
Where DECAY is the output voltage and DAC_VALUE is a number from 0 to 4095.
The Windows Application, in conjunction with the MSP430F1612 microcontroller, utilizes a series of timersto coordinate the rate of steps sent to the device. Once all the control signals are configured accordingly(ENABLEn = LO, SLEEPn = HI, RESETn = HI; DIR, USM0 and USM1 can be HI or LO depending onpreferred mode of operation; SRn must be L, if external diodes are not populated), the motor is ready tobe turned.
10 Laser and Motor Drives SLVA344A – July 2009 – Revised September 2009Submit Documentation Feedback
Table des matières
Autres manuels Texas Instruments Matériel informatique
Texas Instruments
Texas Instruments System-Side Impedance Track bq27500 Manuel utilisateur
Texas Instruments
Texas Instruments AM1808 Manuel utilisateur
Texas Instruments
Texas Instruments TMDXEVM6472 Manuel utilisateur
Texas Instruments
Texas Instruments Hercules RM48 Manuel utilisateur
Texas Instruments
Texas Instruments OMAP5912 Manuel utilisateur
Texas Instruments
Texas Instruments Sub-1 GHz Sensor-to-Cloud Linux E14 Kit Manuel utilisateur
Texas Instruments
Texas Instruments DS90Ux929-Q1EVM Manuel utilisateur
Texas Instruments
Texas Instruments MSP430x11x1 Manuel utilisateur
Texas Instruments
Texas Instruments TMS320C67X+ DSP Manuel utilisateur
Texas Instruments
Texas Instruments HVAL068A Manuel utilisateur
Texas Instruments
Texas Instruments MSP430x1xx Manuel utilisateur
Texas Instruments
Texas Instruments INA149 Manuel utilisateur
Texas Instruments
Texas Instruments MSPM0 Manuel utilisateur
Texas Instruments
Texas Instruments MSP-EXP430F5438 Manuel utilisateur
Texas Instruments
Texas Instruments TRIS TMS37122 Manuel utilisateur
Texas Instruments
Texas Instruments Hercules TMS570LS12 Series Manuel utilisateur
Texas Instruments
Texas Instruments TSC2007EVM Manuel utilisateur
Texas Instruments
Texas Instruments TMS320C6201 Manuel utilisateur
Texas Instruments
Texas Instruments DAC38RF8x Manuel utilisateur
Texas Instruments
Texas Instruments GC5328 Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
