SIIG USB 2.0 Bay Reader/Writer+Floppy Manuel utilisateur

Introducing the Reader/Writer+Floppy

TheUSB2.0BayReader/Writer+Floppyeasilyaddsfront-

accessible multi-format memory card reader/writer

and floppy drive.

FeaturesandBenefits

• All-in-one drive bay design provides easy access

to universal memory card reader/writer and a

floppy drive

• Supports SDHC and CF v4.0 (HSCF with Ultra

DMA mode)

• Direct access port for Micro SD and M2 cards, no

adapter needed

Flash memory card interface

• Compliant with USB specification rev. 2.0

• Works with CompactFlash (CF) Type I & Type II,

Microdrive, SecureDigital (SD), MultimediaCard

(MMC), xD and Memory Stick memory cards

Note: USB 2.0 devices are limited to USB 1.1

speeds when they are connected to a USB 1.1 host

adapter.

Floppy drive interface:

• Supports 1.6MB and 2.0MB floppy diskettes

04-0520A

USB 2.0 Bay

Reader/

Writer+Floppy

Quick Installation Guide

SystemRequirements

• Pentium®or equivalent PC with an available 3.5"

or 5.25" device bay

• An internal USB pin-out header (USB 2.0

recommended)

• A floppy disk drive connector from motherboard

for FDD

• 4-pin power connector from system power supply

• Windows®2000 / XP (32-/64-bit) / Server 2003

(32-/64-bit) / Vista (32-/64-bit)

PackageContents

•USB 2.0 Bay Reader/Writer+Floppy

• 5.25" mounting rack and mounting kit

• USB converter cable (4-pin/TypeA)

• Quick Installation Guide

Layout

Figure 1: Front Panel

Activity/Access LEDM2/Micro SD

SD/MMC/Memory Stick/xD

Floppy disk CF/Microdive

Figure 2. Rear Panel

5.25"MountingRackAssembly

Important:Use the Mounting Rack Assembly only

when installing the hub into a 5.25" drive bay.

Floppy drive connector

Floppy drive power connector

Figure 3: Mounting Rack Assembly

4-pinUSBConnector

Figure 4. 4-pin USB Connector

Note: The 4-pin USB Connector is keyed to plug

intothe4-pinrow of aUSBPin-outHeader. Make

sure that the Red wire is plugged into the +5VDC

pin on the header.

USBPin-outHeader

Onmostmotherboards,theinternalUSBPin-outHeader

consistsof9pinsarrangedin2rows;eachheaderallows

for 2 USB connections (i.e. USB1 and USB2). Normally,

the pins for USB1 and USB2 are in separate rows.

Figure 5. USB Pin-out Header

DATA -

DATA +

GND GND

DATA -

DATA +

+ 5VDC +5VDC

S-GND

Red

Black

Green

White

Pin Assignments

USBConverterCable

The USB Converter Cable is needed if you plan to

connect the Reader/Writer to a Type A USB port instead

of a USB pin-out header.

Match up the wires by color when connecting the

Reader/Writer's 4-pin USB Connector to the USB

ConverterCable's4-pinheader,thenplugtheotherend

into a Type A USB port.

4-pin

header

Type A

connector

Figure 6. USB Converter Cable Connection

Red Wire

Type A

connector

4-pin USB

Connector from

the Reader/Writer

Installing the Reader/Writer+Floppy

Important: InorderfortheReader/Writer+Floppytowork

properly, the driver of your existing USB 2.0 host

adapter must be installed properly.

1. Turn OFF the power to your computer and all

connected peripheral devices.

2. Unplug the power cord from the back of the

computer.

3. Remove the computer cover.

4. Select an available 3.5" or 5.25" drive bay for the

Reader/Writer+Floppy,removethecoverplate from

the selected drive bay.

5. Secure the Reader/Writer+Floppy to the drive bay

by using the supplied mounting screws.

Note: When installing the Reader/Writer+Floppy

into a 5.25" drive bay install it into the 5.25"

mountingrack before mountinginto the drivebay

and follow the same assembly instructions. Refer

to 5.25" Mounting Rack Assembly on page 3.

6. Plug in a mini power connector from the system

powersupplytotheReader/Writer+Floppy'spower

connector. See Figure 7 on page 7.

Note: Youmustconnecttheminipowerconnector

atalltimes. Ifyoudon'tneedthefloppydrive,skip

step 7 and continue to step 8.

7. Connect the floppy drive ribbon cable (not

included) to the Reader/Writer+Floppy's floppy

drive connector. Make sure the stripe on the cable

is on the side opposite the power connector, see

Figure 8 below.

Note: In order for the floppy drive to work, the 4-

pin USB connector must be connected and

operating properly. Go to step 8 for instructions.

Figure 8. Connecting the floppy drive ribbon cable

8. Connect the Reader/Writer+Floppy's 4-pin USB

Connectortothesystem'sinternalUSBport. Refer

to USB Pin-out Header, on page 4 for more

information. Check your system documentation

for the location of the USB pin-out header.

Figure 7. Connecting the Power Cable

Note: If your system has an internal Type-A USB

port you may choose to connect the

Reader/Writer+Floppy's 4-pin USB connector via

the included 4-pin header to USB adapter. Refer

to Figure 6, on page 5 for more information.

9. Replace the computer cover and reconnect the

power cord.

Hardware installation is complete. Go to the next

section,DriverInstallationtocompletetheinstallation.

Driver Installation

Windows2000,XP,Server2003andVistaautomatically

detects and installs the correct drivers for this device.

No driver installation is needed. Refer to Accessing

Memory Cards, on page 9, to use your Reader/

Writer+Floppy.

To Verify Successful Driver Installation

1. Check Device Managerto verify successful driver

installation.

Windows 2000/XP/Server 2003: Right click My

Computer, click Manage, then click Device

Manager.

Windows Vista™: Right click Computer, click

Manage, click Continue, then click Device

Manager.

2. DoubleclickUniversalSerialBuscontrollers. USB

Mass Storage Device should be listed.

3. Double click Disk drives. Generic 2.0 Reader...

should be listed three times.

Inserting Memory Cards and Floppy Disk

For CompactFlash, MicroSD, M2, IBM MicroDrive,

Memory Stick, MultiMediaCard and SecureDigital

memory cards, insert with the top label facing up.

For Floppy disks, insert with the top label facing up.

Accessing Memory Cards

WhentheReader/Writer+Floppyissuccessfullyinstalled,

three Removable Disk icons appear in My Computer.

To access any one drive, double click the icon that

corresponds to the memory card.

Activity/Access LED

Red LED will be lit when a flash memory card is

inserted. When any flash memory card is not inserted,

the red LED will go off.

FlashMemoryCard

Red LED will flash when accessing any memory card.

FloppyDrive

Green LED will flash when accessing a floppy diskette.

Removing Inserted Media

Do not remove flash memory cards and/or a floppy

diskette when theActivity/Access LED is flashing/on.

Wait until the LED is off for several seconds before

removing any inserted media.

Blank Page

Table des matières

Autres manuels SIIG Matériel informatique

SIIG

SIIG Single-Serial PC Card Manuel utilisateur

SIIG

SIIG JU-91RW12-S4 Manuel utilisateur

SIIG

SIIG Serial ATA 4-Channel PCI Manuel utilisateur

SIIG

SIIG JJ-EC2011-S1 Manuel utilisateur

SIIG

SIIG I/O Expander 2S Manuel utilisateur

SIIG

SIIG CE-H23J11-S1 Manuel utilisateur

SIIG

SIIG JJ-EC1012-S1 Manuel utilisateur

SIIG

SIIG DP FireWire 800 3-Port PCIe Manuel utilisateur

SIIG

SIIG eSATA II PCIe i/e Manuel utilisateur

SIIG

SIIG SATA II-150 PCI Manuel utilisateur

SIIG

SIIG NN-E20022-S1 Manuel utilisateur

SIIG

SIIG FireWire Home DV Kit Manuel utilisateur

SIIG

SIIG Silent Mini Notebook Cooler Manuel utilisateur

SIIG

SIIG UltraATA 133 PCI Manuel utilisateur

SIIG

SIIG JU-EP0012-S1 Manuel utilisateur

SIIG

SIIG JU-PCM422-S2 Manuel utilisateur

SIIG

SIIG ID-P40411-S1 Manuel utilisateur

SIIG

SIIG JU-P40311-S1 Manuel utilisateur

SIIG

SIIG Dual Profile Hi-Speed USB 4-Port PCI Manuel utilisateur

SIIG

SIIG CyberParallel Dual Manuel utilisateur

SIIG

SIIG ExpressCard/54 CF R/W Manuel utilisateur

SIIG

SIIG DP SoundWave 4 Channel PCI Manuel utilisateur

SIIG

SIIG NN-403P12 Manuel utilisateur

SIIG

SIIG CyberParallel Dual Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur