SIIG 1-Port ECP Manuel utilisateur
1
DP 1-Port ECP/EPP
Parallel PCIe
Quick Installation Guide
04-0718B
Introduction
The DP 1-Port ECP/EPP Parallel PCIe high-speed
parallel card provides one additional parallel
port to your PCIe Express enabled system.
Key Features and Benefits
• PCI Express 1-lane (x1) adapter that works
in any PCI Express slot
• Dual Profile design to work with standard
height and low profile chassis
• Compliant with PCI Express Base
Specification, Revision 1.1
• Supports ECP, EPP, and SPP parallel port
modes
2
Figure 1: Board Layout
Parallel Port
System Requirements
• PCI Express enabled system with an
available PCI Express slot
• Windows®8 (32-/64-bit) / 7 (32-/64-bit) /
Vista (32-/64-bit) / XP (32-/64-bit) / Server
2003 & 2008 (32-/64-bit) / Server 2008 R2
/ 2000
Package Contents
•DP 1-Port ECP/EPP Parallel PCIe adapter
• Spare enhanced low-profile bracket
• Driver CD
• Quick installation guide
Layout
3
Hardware Installation
General instructions for installing the card are
provided below. Since the design of computer
cases and motherboards vary, refer to your
computer’s reference manual for further
information, if needed.
Static Electricity Discharge may permanently
damage your system. Discharge any static
electricity build up in your body by touching your
computer’s case for a few seconds. Avoid any
contact with internal parts and handle cards
only by their external edges.
Note: for low profile chassis, remove the
standard height bracket and install the
enhanced low-profile bracket now.
1. Turn OFF the power to your computer and
any other connected peripheral devices.
2. Unplug the power cord from the computer.
3. Remove the computer cover.
4. Remove the slot bracket from an available
PCI Express slot.
4
5. To install the card, carefully align the card's
bus connector with the selected PCI Express
slot on the motherboard. Push the board
down firmly, but gently, until it is well
seated.
6. Replace the slot bracket's holding screw to
secure the card.
7. Replace the computer cover and reconnect
the power cord.
Driver Installation
Please make sure the board is installed before
proceeding with driver installation.
Windows 8 (32-/64-bit) / 7 (32-/64-bit)
1. Insert the driver CD, close the AutoPlay
box if displayed.
2. Click Windows key and R, type
D:\setup.exe, click OK. (Change D: to
match your CD/DVD-ROM drive letter)
3. At User Account Controls, click Yes.
5
4. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
Windows Vista (32-/64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD, close the AutoPlay
box if displayed.
4. Click Start, in the Start Search box, type
D:\setup.exe, press Enter. (Change D: to
match your CD/DVD-ROM drive letter)
5. At User Account Controls, click Allow.
6. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
6
Windows XP (32-/64-bit) / Server 2003 (32-/
64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD.
4. Click Start, then Run. Type D:\setup.exe,
click OK. (Change D: to match your CD/
DVD-ROM drive letter)
5. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
Windows Server 2008 (32-/64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD, close the AutoPlay if
displayed.
4. Click Start, in the Start Search box, type
D:\setup.exe, press Enter. (Change D: to
match your CD/DVD-ROM drive letter)
7
5. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
Windows Server 2008 R2
1. Install the board and boot up Windows.
2. Insert the driver CD, close the AutoPlay
box if displayed.
3. Click Start, in the Search programs and
files box, type D:\setup.exe, press Enter.
(Change D: to match your CD/DVD-ROM
drive letter)
4. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
Windows 2000
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD.
8
4. Click Start, then Run. Type D:\setup.exe,
click OK. (Change D: to match your CD/
DVD-ROM drive letter)
5. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
To Verify Windows Installation
1. Check in Device Manager to verify
installation.
For Windows 8 / 7: Right click Computer,
click Manage, then click Device Manager.
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
For Windows XP / Server 2003 / 2000: Right
click My Computer, click Manage, click
Device Manager.
For Windows Server 2008 / Server 2008 R2:
Right click Computer, click Manage, double
click Diagnostics, click Device Manager.
9
2. Click on the +(plus sign) in front of Ports
(COM & LPT), PCI Express ECP Parallel
Port (LPT...) should be displayed.
Changing Parallel Port Number
Some parallel port devices need a specific LPT in
order to work. If your parallel port device works
properly, do not change this setting.
1. From the Device Manager window double
click Ports (COM & LPT), then double click
PCI Express ECP Parallel Port (LPT...).
2. Click the Port Settings tab.
3. Click the down arrow next to the LPT Port
number box, then select a parallel port that
is not in use.
4. Click OK to save the changes, then close the
Device Manager.
10
Blank Page
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels SIIG Matériel informatique
SIIG
SIIG CyberParallel Dual Manuel utilisateur
SIIG
SIIG CyberParallel ExpressCard Manuel utilisateur
SIIG
SIIG eSATA II PCIe i/e Manuel utilisateur
SIIG
SIIG DP PCI-to-PS/2 Manuel utilisateur
SIIG
SIIG ExpressCard/54 CF R/W Manuel utilisateur
SIIG
SIIG DP FireWire 800 PCIe Manuel utilisateur
SIIG
SIIG 1 FireWire 800 CardBus DV-Ki Manuel utilisateur
SIIG
SIIG Low Profile USB Adapter Manuel utilisateur
SIIG
SIIG SATA II-150 PCI Manuel utilisateur
SIIG
SIIG FireWire 800 2-Port ExpressCard/34 Manuel utilisateur
SIIG
SIIG JU-P40311-S1 Manuel utilisateur
SIIG
SIIG Network Device EVTEK-5103 Guide d'installation
SIIG
SIIG UltraATA 100 Pro Manuel utilisateur
SIIG
SIIG CyberParallel Dual Manuel utilisateur
SIIG
SIIG JU-PCM422-S2 Manuel utilisateur
SIIG
SIIG 1394 Dual-Port CardBus Manuel utilisateur
SIIG
SIIG USB 2.0+1394 DV Kit Manuel utilisateur
SIIG
SIIG NN-000032-S1 Manuel utilisateur
SIIG
SIIG CE-ED0011-S1 Manuel utilisateur
SIIG
SIIG DP PCI-to-PS/2 Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
