ProLights SmartBat PlusG2 Manuel utilisateur

USER MANUAL

REV.01-10/22 English version

SmartBat PlusG2

4x20W hybrid battery uplighter/spot,

IP65, with RGB + Warm White LED source,

wireless or wired

Thank you for choosing PROLIGHTS

Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements

for professionals and designed and manufactured for the use and application as shown in this document.

Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be

a source of danger.

This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively

applicable national accident prevention rules and regulations.

Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated

companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other

loss occasioned by the use of, inability to use or reliance on the information contained in this document.

Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial

PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).

Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad

set of always updated technical documentation: specications, user manual, technical drawings, photometrics,

personalities, xture rmware updates.

The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services

or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.

04026 - Minturno (LT) ITALY.

Visit the download area

of the product page

PROLIGHTS - SmartBat PlusG2 01

INDEX

SAFETY INFORMATION 02

1 - PACKAGING 07

PACKAGE CONTENT..................................................................................................... 07

OPTIONAL ACCESSORIES............................................................................................. 07

2 - TECHNICAL DRAWING 07

3 - INSTALLATION 08

MOUNTING.................................................................................................................... 08

4 - CONNECTION TO THE MAINS SUPPLY 09

5 - START UP 09

CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 09

6 - PRODUCT OVERVIEW 10

7 - DMX CONNECTION 11

CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 11

INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 11

CONNECTION DAISY CHAIN........................................................................................ 11

CONNECTION OF THE DMX LINE................................................................................ 11

CONSTRUCTION OF THE DMX TERMINATION ........................................................... 12

DMX ADDRESSING ........................................................................................................ 12

OPERATION AS A WIRELESS TRANSMITTER................................................................ 12

IN TO WDMX ................................................................................................................. 13

OPERATION AS A WIRELESS RECEIVER........................................................................ 13

WDMX TO DMX (RX)...................................................................................................... 13

8 - CONTROL PANEL 14

DISPLAY AND BUTTONS LAYOUT................................................................................. 14

9 - MENU STRUCTURE 15

10 - SHORTCUT 19

11 - RDM FUNCTIONS 20

12 - DMX CHARTS 24

CHANNEL DEFINITION ................................................................................................. 25

13 - ERROR MESSAGES 32

14 - ACCESSORIES INSTALLATION 33

SINGLE BATTERY (CODE SBPG2BAT - INCLUDED) ...................................................... 33

LIGHT DIFFUSION FILTER (CODE SBPG2FILTER20 / 40 / 60 / 1060 - OPTIONAL)....... 34

FLOOR BRACKET (CODE SBPG2FY - OPTIONAL) ........................................................ 35

HANGING BRACKET (CODE SBPG2HY - OPTIONAL) .................................................. 36

BALL HEAD JOINT (CODE EPTWCBHEAD - OPTIONAL) ............................................. 37

15 - TEST OF IP65 RATING 38

16 - MAINTENANCE 39

MAINTENANCE AND CLEANING THE PRODUCT........................................................ 39

VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 39

TROUBLESHOOTING..................................................................................................... 40

PROLIGHTS - SmartBat PlusG2

SAFETY INFORMATION

WARNING!

• Please read carefully the instruction reported in this section before installing, powering,

operating or servicing the product and observe the indications also for its future handling.

Lithium-Ion Battery Maintenance Guidelines

Lithium-Ion rechargeable batteries products require routine maintenance and care in

their use and handling. Read and follow the guidelines in this document to safely use

Lithium-Ion batteries and achieve the maximum battery life span.

Misusing the battery projector may cause the battery to get hot, break, or ignite, and

cause serious injury.

Overview

• Only authorised technicians may service the battery.

• Use only Prolights approved batteries in your Prolights products.

• Do not leave the projector unused for extended periods of time in storage.

• Lithium-Ion batteries continue to slowly discharge (self-discharge) when not in use or

while in storage. Routinely check the battery’s charge status.

• The typical estimated life of a Lithium-Ion battery is about two years or around 300

charge cycles, whichever occurs rst. One charge cycle is a period of use from fully

charged, to fully discharged, and fully recharged again.

• For batteries that do not complete full charge cycles the life expectancy can be less

than two years also.

• Rechargeable Lithium-Ion batteries have a limited life and will gradually lose their

capacity to hold a charge. This loss of capacity (ageing) is irreversible. As the battery

loses capacity, the length of time it will power the product (run time) decreases.

Battery Maintenance

• The run time of your battery will vary depending on the product’s conguration and

the applications that you run.

• Routinely check the battery’s charge status.

• Carefully monitor batteries that are approaching the end of their estimated life.

• It is mandatory to replace the battery with a new one to prevent eventual risk of over-

heating and subsequent explosion, if you note either of the following:

1. The battery run time drops below about 70% of the original run time.

2. The battery charging time increases signicantly.

3. The projector heats up while charging beyond normal temperatures.

4. In case of any collisions, falls, particular thermal stresses.

• If a battery is stored or otherwise unused for an extended period, be sure to follow

the storage instructions in this document.

• Always recharge immediately when the battery is low.

• If you do not follow the instructions, and the battery has no charge remaining when

you check it, consider it to be damaged. Do not attempt to recharge it or to use it.

Replace it with a new battery.

PROLIGHTS - SmartBat PlusG2 03

Charging

• Refer to your product’s user manual and/or online help for detailed information about

charging its battery. The latest version of your Prolights product user manual is avail-

able at www.prolights.it.

• Avoid charging if the projector has any damage, malfunction, tampering or signs of

moisture inside.

• Do not charge unattended.

• Always charge with its packing/ight-case open.

• Always follow the charging instructions provided.

• Only charge the battery mounted in the xture with the original charger. Do not use

a third party charger.

• It is recommended to charge at a temperature between 15°C and 35°C.

• Do not recharge the product longer than required, it will affect the battery capacity

and can cause overheating.

• For the IP product you need to make sure that the projector housing and charging

connector are dry without any moisture.

Storage

• Store the product in an airy, dry place, and away from any inammable object in order

to ensure optimum storage conditions for the battery.

• Do not expose the battery projector to re or heat.

• Charge or discharge the battery to approximately 50% of capacity before storage.

• Charge the battery to approximately 50% of capacity at least once every six months.

• Store the product projector at temperatures between 5 °C and 20 °C (41 °F and 68

°F).

Handling Precautions

• Do not disassemble, crush, or puncture a battery.

• Do not short the external contacts on a battery.

• Do not dispose of a battery in re or water.

• Do not expose a battery to temperatures above 60 °C (140 °F).

• Avoid exposing the battery to excessive shock or vibration.

• Do not use a damaged battery.

• If a battery pack has leaking uids, do not touch any uids. Dispose of a leaking bat-

tery pack (see Disposal and Recycling in this document).

• In case of eye contact with uid, do not rub eyes. Immediately ush eyes thoroughly

with water for at least 15 minutes, lifting upper and lower lids, until no evidence of

the uid remains. Seek medical attention.

Transportation

• Always check all applicable local, national, and international regulations before trans-

porting a Lithium-Ion battery.

• Transporting an end-of-life, damaged, or recalled battery may, in certain cases, be

specically limited or prohibited.

Disposal and Recycling

• Lithium-Ion batteries are subject to disposal and recycling regulations that vary by

country and region. Always check and follow your applicable regulations before dis-

posing of any battery. Contact your local battery recycling organisation.

• Many countries prohibit the disposal of waste electronic equipment in standard waste

receptacles. Place only discharged batteries in a battery collection container.

• Use electrical tape or other approved covering over the battery connection points to

prevent short circuits.

PROLIGHTS - SmartBat PlusG2

This unit is not for household and residential use, only professional applications.

Connection to mains supply

• The Connection to the mains supply must be carried out by a qualied electrical

installer.

• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected

to ground (earth).

• Select the cable cross section in according with the maximum current draw of the

product and the possible number of products connected at the same power line.

• The AC mains power distribution circuit must be equipped with magnetic+residual

current circuit breaker protection.

• Do not connect it to a dimmer system; doing so may damage the product.

Protection and Warning against electrical shock

• Do not remove any cover from the product, always disconnect the product from AC

power before servicing.

• Ensure that the xture is electrically connected to ground (earth). And use only a

source of AC power that complies with local building and electrical codes and has

both overload and ground-fault (earth-fault) protection.

• Before using the xture, check that all power distribution equipment and cables are

in perfect condition and rated for the current requirements of all connected devices.

• Isolate the xture from power immediately if the power plug or any seal, cover, cable, or

other components are damaged, defective, deformed or showing signs of overheating.

• Do not reapply power until repairs have been completed.

• Refer any service operation not described in this manual to PROLIGHTS Service team

or an authorized PROLIGHTS service center.

Installation

• Make sure that all visible parts of the product are in good visible condition before its

use or installation.

• Make sure the point of anchorage is stable before positioning the projector.

• When suspending the xture above ground level, secure it against failure of primary

attachments by attaching a safety cable that is approved as a safety attachment for

the weight of the xture to the attachment point on the main frame of the product. ln

case the safety cable, enter in action, it needs to be replaced with a new one.

• Install the product only in well ventilated places.

• For non temporary installations, ensure that the xture is securely fastened to a load-

bearing surface with suitable corrosionresistant hardware.

• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or

screws are turned fully, and secured with a suitable safety cable.

0.5 m Minimum distance of illuminated objects

• The projector needs to be positioned so that the objects hit by the beam of light are

at least 0,5 meters (1,64 ft) from the lens of the projector.

T 45°C

Max operating ambient temperature (Ta)

• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).

0°C

Minimum operating ambient temperature (Ta)

• Do not operate the xture if the ambient temperature (Ta) is below 0 °C (32 °F).

PROLIGHTS - SmartBat PlusG2 05

Protection from burns and re

• The exterior of the xture becomes hot during use. Avoid contact by persons and

materials.

• Ensure that there is free and unobstructed airow around the xture.

• Keep ammable materials well away from the xture.

• Do not expose the front glass to sunlight or any other strong light source from any an-

gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.

• Do not attempt to bypass thermostatic switches or fuses.

IP65

Outdoor (temporary) use

• This product is rated with an IP (Ingress protection) for temporary outdoor use when

used and serviced according to the instruction contained in this document.

• Never use the xture in places subject to vibrations or bumps.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Excessive dust, smoke uid, and particle build up degrades performance, causes

overheating and will damage the xture.

• Damages caused by inadequate cleaning or maintenance are not covered by the

product warranty.

60°

cTemperature of the external surface

• The surface of the xture can reach up to 60 °C (140 °F) during operation. Avoid

contact with people and materials.

Maintenance

• Warning! Disconnect the xture from AC mains power and allow to cool for at least

10 minutes before handling.

• Only technicians who are authorized by PROLIGHTS or Authorised service partners

are permitted to open the xture.

• Users may carry out external cleaning, following the warnings and instructions pro-

vided, but any service operation not described in this manual must be referred to a

qualied service technician.

• Important! Excessive dust, smoke uid, and particle build up degrades performance,

causes overheating and will damage the xture. Damages caused by inadequate

cleaning or maintenance is not covered by the product warranty.

Photobiological safety

• This device emits potentially dangerous optical radiation and is identied in the cat-

egory of Risk Group 2 according to EN 62471.

Minimun

distance

Risk

Group 2

Risk

Group 1

0.2 m

0.7 ft

4,64 m

15,22 ft

Do not stare at the operating light source

• Do not look directly at the LED source during operation. It can be harmful to the eyes

and skin.

• During Installation, operation and maintenance, be prepared for the xture to light

and move suddenly when connected to power.

• The device should be positioned so that prolonged staring into the luminaire at a

distance closer than 10,50 m (34,45 ft) is not expected.

PROLIGHTS - SmartBat PlusG2

Disposal

• This product is supplied in compliance with European Directive 2012/19/EU – Waste

Electrical and Electronic Equipment. (WEEE). To preserve the environment please

dispose/ recycle this product at the end of its life according to the local regulation.

The products to which this manual refers comply with:

• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).

• 2014/30/EU - Electromagnetic Compatibility (EMC).

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS.

• 2014/53/EU - Radio Equipment Directive (RED).

The products to which this manual refers comply with:

• UL 1573 + CSA C22.2 No. 166 - Stage and Studio Luminaires and Connector Strips.

• UL 1012 + CSA C22.2 No. 107.1 - Standard for power units other than class 2.

FCC Compliance:

• This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-

lowing two conditions:

5. This device may not cause harmful interference, and

6. This device must accept any interference received, including interference that may

cause undesired operation.

Other approvals

• The product meets the safety requirements of the certification procedures of the

market in which it is placed and sold.

PROLIGHTS - SmartBat PlusG2 07

1 - PACKAGING

PACKAGE CONTENT

• 1x SMARTBATPLUSG2.

• 1x lter frame.

• 1x half top hat.

• 1x connector cover plate.

• 1x SBPG2BAT: single battery for SMARTBATPLUSG2.

• 1x 1,5 meters power cable (BARE END - SEETRONIC IP65 power connector).

• User Manual.

OPTIONAL ACCESSORIES

• SBPG2FYBK/WH/CR/GL: oor bracket for SMARTBATPLUSG2, black/white/chrome/gold.

• SBPG2HYBK/WH/CR/GL: hanging bracket for SMARTBATPLUSG2, black/white/ chrome/ gold.

• SBPG2CKBK/WH/CR/GL: cover kit for SMRATBATPLUSG2, black/white/ chrome/ gold.

• SBPG2FILTER20: simmetric 20° light diffusion lter for SMARTBATPLUSG2 projector.

• SBPG2FILTER40B: simmetric 40° light diffusion lter for SMARTBATPLUSG2 projector.

• SBPG2FILTER60: simmetric 60° light diffusion lter for SMARTBATPLUSG2 projector

• SBPG2FILTER1060: asymmetric 10°x60° Light diffusion lter for SMARTBATPLUSG2 projector.

• FCLSMARTBATPG2: ight case for 6 SMARTBATPLUSG2, battery charger included

• PRL-IRC: RGBWA IR: controller, 29 buttons, manual/static colours, auto programs, fade.

• C6002A/B: slim aluminium clamp, 200 kg loading, 48-51 mm tubes, M10 bolt, silver/black.

• RSR0630A/B: steel security cable for hanging bodies, inox steel shackle, L=60 cm, silver/black.

• 9533FXWL03: ass. 3x2.5mm TH07 cable, SHUKO plug, MENAC3FXW socket, L.3m.

• WSBBR512G5: blackBox R-512 G5 receiver 512Ch, 2.45GHz & 5.8GHz, DMX/RDM optional.

• WSBBF1G6: BlackBox F-1 G6 transrec, 512ch, 2.45GHz, DMX&RDM,Bluetooth,G3,G4,G4S, G5, CRMX.

• WSBBF1G5: blackBox F-1 G5 transmitter, 2,45GHz & 5.2/5,8 GHz, DMX/RDM, 512Ch.

• WSBBR512G6: blackBox R-512 G6 receiver 512Ch, 2.45GHz,DMX&RDM,Bluetooth,G3,G4,G4S,G

5,CRMX.

• UPBOX1UP5: rmware uploader kit, USB IN, 5pin XLR DMX OUT, USB OUT.

214 mm

[8.4 in]

Ø182 mm

[7.2 in]

Fig. 01

Weight: 5,7 kg - 12,56 lbs

2 - TECHNICAL DRAWING

PROLIGHTS - SmartBat PlusG2

Fig. 02

3 - INSTALLATION

MOUNTING

Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,

auxiliary equipment, etc. and complies with locally applicable regulations.

When suspending the xture above ground level, secure it against failure of primary attachments by

attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor

point on the product main frame.

Do not use removable parts or weak anchors for secondary attachment.

Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-

pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.

C6002

clamp

RSR0630A/B

Steel security cable

13 mm

0,51 in

223 mm

8,8 in

45 mm

1,8 in

Press this

button to

tilt the projector

Table des matières

Autres manuels ProLights Matériel de DJ

ProLights

ProLights CROMOSPOT400 Manuel utilisateur

ProLights

ProLights POLAR500 Manuel utilisateur

ProLights

ProLights MINICLIPSEWD Manuel utilisateur

ProLights

ProLights VORTEX VXBUBBLE Manuel utilisateur

ProLights

ProLights VIRTUALDRAPE Manuel utilisateur

ProLights

ProLights LUMIPAR12HPRO Manuel utilisateur

ProLights

ProLights STUDIOCOBFC Manuel utilisateur

ProLights

ProLights ARENACOB4HALO Manuel utilisateur

ProLights

ProLights PHYROBUB Manuel utilisateur

ProLights

ProLights CROMOSPOT500 Manuel utilisateur

ProLights

ProLights ARIA 700SPOT Manuel utilisateur

ProLights

ProLights PIXIEWASH Manuel utilisateur

ProLights

ProLights MINIECLFRFC Manuel utilisateur

ProLights

ProLights HZ660D Manuel utilisateur

ProLights

ProLights SMARTTUBE32 Manuel utilisateur

ProLights

ProLights PHYRO1200SNOW Manuel utilisateur

ProLights

ProLights ARCLED7337VW Manuel utilisateur

ProLights

ProLights ARCPOD27Q Manuel utilisateur

ProLights

ProLights LEDPAR64363RGB Manuel utilisateur

ProLights

ProLights LUMIPAR12UQ Manuel utilisateur

ProLights

ProLights ECLIPSEHDTWC Manuel utilisateur

ProLights

ProLights LUMIPAR12UQPRO Manuel utilisateur

ProLights

ProLights CONFETTIGUNNER Manuel utilisateur

ProLights

ProLights ARCLED7307HD Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur