Pepperl+Fuchs VBA-4E-KE5-IL Manuel utilisateur

Spec 2.1

VBA-4E-KE5-IL

AS-Interface Analog Module

FACTORY A TOMATION

MAN AL

With regard to the supply of products, the current issue of the following document is ap-

plicable: The General Terms of Delivery for Products and Services of the lectrical Indus-

try, published by the Central Association of the lectrical Industry (Zentralverband

lektrotechnik und lektroindustrie (ZV I) e.V.) in its most recent version as well as the

supplementary clause: " xpanded reservation of proprietorship"

VBA-4 -K 5-IL

1 Introduction................................................................................. 5

1.1 Content of this Document ................................................................... 5

1.2 Target Group, Personnel...................................................................... 5

1.3 Symbols sed ...................................................................................... 5

2 Certificates and Approvals ........................................................ 7

2.1 L Information...................................................................................... 7

3 Product Description ................................................................... 8

3.1 Intended se ........................................................................................ 8

3.2 Displays and Operating Elements ...................................................... 8

3.3 Connections ......................................................................................... 9

3.4 Automatic Activation of Input Channels ............................................ 9

3.5 Resetting the Automatically Detected Sensor Types ..................... 10

3.6 Manual Activation of the Input Channels......................................... 10

4 Installation................................................................................. 11

4.1 Storage and Transport ....................................................................... 11

4.2 npacking........................................................................................... 11

4.3 Mounting ............................................................................................. 11

4.4 AS-Interface/Auxiliary Voltage Connection ..................................... 11

4.5 Connecting the Sensors.................................................................... 12

5 Commissioning......................................................................... 13

5.1 Assigning an Address to the Module............................................... 13

5.2 Slave Profile........................................................................................ 13

5.3 Parameterization ................................................................................ 13

6 Troubleshooting........................................................................ 15

6.1 Causes and Elimination of a Peripheral Fault ................................. 15

6.2 Causes and Elimination of a Channel Fault..................................... 15

7 Appendix A................................................................................ 16

7.1 Analog Input Module Measuring Ranges ........................................ 16

7.2 Delay Times ........................................................................................ 16

VBA-4 -K 5-IL

Introduction

2018-07

1 Introduction

1.1 Content of this Document

This document contains information required to use the product in the relevant phases of the

product life cycle. This may include information on the following:

■

Product identification

■

Delivery, transport, and storage

■

Mounting and installation

■

Commissioning and operation

■

Maintenance and repair

■

Troubleshooting

■

Dismounting

■

Disposal

The documentation comprises the following parts:

■

This document

■

Datasheet

In addition, the documentation may comprise the following parts, if applicable:

■

U-type examination certificate

■

U declaration of conformity

■

Attestation of conformity

■

Certificates

■

Control drawings

■

Instruction manual

■

Other documents

1.2 Target Group, Personnel

Responsibility for planning, assembly, commissioning, operation, maintenance, and

dismounting lies with the plant operator.

Only appropriately trained and qualified personnel may carry out mounting, installation,

commissioning, operation, maintenance, and dismounting of the product. The personnel must

have read and understood the instruction manual and the further documentation.

Prior to using the product make yourself familiar with it. Read the document carefully.

Note!

For full information on the product, refer to the further documentation on the Internet at

www.pepperl-fuchs.com.

2018-07

VBA-4 -K 5-IL

Introduction

1.3 Symbols Used

This document contains symbols for the identification of warning messages and of informative

messages.

Warning Messages

You will find warning messages, whenever dangers may arise from your actions. It is mandatory

that you observe these warning messages for your personal safety and in order to avoid

property damage.

Depending on the risk level, the warning messages are displayed in descending order as

follows:

Informative Symbols

Action

This symbol indicates a paragraph with instructions. You are prompted to perform an action or

a sequence of actions.

Danger!

This symbol indicates an imminent danger.

Non-observance will result in personal injury or death.

Warning!

This symbol indicates a possible fault or danger.

Non-observance may cause personal injury or serious property damage.

Caution!

This symbol indicates a possible fault.

Non-observance could interrupt the device and any connected systems and plants, or result in

their complete failure.

Note!

This symbol brings important information to your attention.

VBA-4 -K 5-IL

Certificates and Approvals

2018-07

2 Certificates and Approvals

2.1 UL Information

Technical Data and Environmental Conditions

This device is for indoor use only.

This device may be operated in altitudes up to 2000 m.

The ambient temperature range is from -25 °C to +70 °C.

The device must be installed in accordance with applicable national laws and regulations.

If the device is used in a manner not specified by the manufacturer, the protection provided by

the equipment may be impaired.

The device must be installed in a switch cabinet or switch box that meets protection class IP54

as a minimum.

2018-07

VBA-4 -K 5-IL

Product Description

3 Product Description

3.1 Intended Use

The VBA-4 -K 5-IL is an analog module for connecting up to four sensors 0/4 ... 20 mA to the

AS-Interface network. Data conversion and data transfer are provided asynchronously

according to AS-Interface profile 7.3. The data is converted internally at a 16 bit resolution. The

analog module features four analog current inputs. Power is supplied to the sensors by the

auxiliary voltage.

3.2 Displays and Operating lements

Figure 3.1 Indicators and Operating lements

The VBA-4 -K 5-IL analog module is equipped with the following indicators and operating

elements:

LED Indicators

PWR L D AS-Interface voltage; green L D

Green: voltage OK

Green, flashing: address is 0 or peripheral fault

FAULT L D Fault indication; red L D

Red: communication fault or address is 0

Red, flashing: peripheral fault

AUX L D xt. auxiliary voltage U

AUX

; dual green/red L D

Green: voltage OK

Red: voltage reversed

IN1 L D

IN2 L D

IN3 L D

IN4 L D

Status input signal; yellow L D

Yellow: input value within measuring range

Yellow, flashing: wire break or input value outside of

measuring range

Off: channel is disabled

PWR

FLT

AUX

ADDR

VBA-4 -K 5-IL

Product Description

2018-07

3.3 Connections

Figure 3.2 Connections

3.4 Automatic Activation of Input Channels

All input channels are deactivated by default. Wire break detection is activated (parameter bit

P3 = 1). The measuring range is 4 mA ... 20 mA. The analog module checks the input signals

to detect and automatically activate the connected inputs. This state is indicated by the four

yellow L Ds IN1 ... IN4 illuminating in sequence until at least one connected input is detected.

If no connected input is detected, the peripheral fault is set after 5 seconds. Automatic

activation is still possible.

Activating an Input Channel

An input channel is activated if an input signal within a range of 1 mA ... 23 mA is present. Any

activated inputs remain active after the module is restarted. The sequence and number of

activated inputs can be chosen as required. To use the automatic activation, no jumpers may

be installed between GND and 1CH, 2CH, or 3CH.

Abbreviation xplanation

ADDR Addressing socket; extra-low-voltage switch socket, Ø 1.3 mm

II1 ... II4 Current at analog inputs

L+ Sensor supply

GND Reference potential for inputs and sensors

1CH, 2CH, 3CH Jumpers for input configuration

ASI+

ASI-

AS-Interface; both ASI+ terminals and both ASI- terminals are

bridged in the terminal block.

AUX+

AUX-

Auxiliary voltage; both AUX+ terminals and both AUX-

terminals are bridged in the terminal block.

GND

2CH

1CH

GND

AUX+

AUX-

ASI+

ASI-

II1

L+

II2

L+

3CH

GND

II3

L+

II4

L+

AUX+

AUX-

ASI+

ASI-

ADDR

Note!

If wire break detection is disabled (parameter bit P3 = 0), automatic activation is switched off

and all four input channels are activated. The measuring range is 0 mA ... 20 mA. The number

of active input channels can be set by activating them manually using a jumper between GND

and 1CH, 2CH, or 3CH. See chapter 3.6.

2018-07

VBA-4 -K 5-IL

Product Description

3.5 Resetting the Automatically Detected Sensor Types

Any sensor types saved through automatic detection are reset when the input configuration of

the module is manually changed. For this, there are two available options:

1. Switch off the module power supply. Place or remove the jumper between 1CH, 2CH, or

3CH, and GND, then switch on the supply voltage again.

2. Change the status of parameter P3 (see chapter 5.3). In this case, it is not necessary to

switch the supply voltage off and on.

Repeat this process if necessary to return to the required input configuration.

3.6 Manual Activation of the Input Channels

The number of active input channels can be determined using a jumper between the GND and

1CH, 2CH, and 3CH terminals.

Note!

Any change made to the input configuration via a jumper between 1CH, 2CH, or 3CH, and

GND is only detected once the supply voltage is switched on. Changes made via parameter P1

can also be implemented during ongoing operation. See chapter 5.3.

Do not connect the 1CH, 2CH, 3CH, and GND connections to external potentials. The length of

the jumpers must not exceed 5 cm.

Bridging terminals xplanation

Automatic detection active (if parameter bit

P3 = 1). See chapter 3.4 and see chapter 5.3.

Only input channel 1 active

Input channels 1 and 2 active

Input channels 1, 2, and 3 active

2CH

1CH

3CH

GND

2CH

1CH

3CH

GND

2CH

1CH

3CH

GND

2CH

1CH

3CH

GND

Note!

Any change made to the input configuration via a jumper between GND and 1CH, 2CH, or 3CH

is only detected once the AS-Interface supply voltage is switched on.

Do not connect the 1CH, 2CH, 3CH, and GND connections to external potentials.

The length of the jumpers must not exceed 5 cm.

VBA-4 -K 5-IL

Installation

2018-07

4 Installation

4.1 Storage and Transport

For storage and transport purposes, package the unit using shockproof packaging material

and protect it against moisture. The best method of protection is to package the unit using the

original packaging. Furthermore, ensure that the ambient conditions are within allowable range.

4.2 Unpacking

Check the product for damage while unpacking. In the event of damage to the product, inform

the post office or parcel service and notify the supplier.

Retain the original packaging in case the device must be stored or shipped again at a later

date.

Should you have any questions, please contact Pepperl+Fuchs.

4.3 Mounting

Mount the module by snapping it onto a 35 mm DIN rail in compliance with N 50022.

nlocking Terminal Blocks

Proceed as follows to unlock and eject terminal blocks:

Figure 4.1 Unlocking terminals

4.4 AS-Interface/Auxiliary Voltage Connection

Two terminals are always available for ASI+, ASI-, AUX+, and AUX- to make it easier to loop the

leads through. ach of these pairs of terminals is bridged in the terminal block. This ensures

the connection is retained even if the terminal block is disconnected from the module.

1. Lift the label carrier upwards.

2. Guide a suitable screwdriver through the eye on the ejector and then:

■

Insert the blade of the screwdriver on the bottom of the foot bolt.

■

Then pull on the handle of the screwdriver in the direction indicated.

3. Remove the terminal block.

Table des matières

Autres manuels Pepperl+Fuchs Unité de contrôle

Pepperl+Fuchs

Pepperl+Fuchs 7500 Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VU121 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E-KE1-S Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs IQT-F116-R4M-V1 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VBA-2A-KE5-IL/UL Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs SC2-2 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E2A1A-KE3-ZEL/E2L/SEL Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs 5500 Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E4A-G20-ZEJ/M3L-P9 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-2HB17-2V1D Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E4A-G20-ZEJ/M48L-P12 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E-G4-SN Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs KFD2-DWB-Ex1.D Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PSU-IDM160-BD-1D-J1-N0 Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs 5500 Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs ICE1-8IOL-S2-G60L-V1D Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E2A-KE1P-S/E2 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E4A-G20-ZEJ/M3L-P10 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PS1000-A6-24.10.R Manuel

Pepperl+Fuchs

Pepperl+Fuchs VBA-2E-KE5-IJL Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-1HB6-2V15B Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VU120 Guide de référence

Pepperl+Fuchs

Pepperl+Fuchs ICE11-8IOL-G60L-V1D Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-2HB6-V15B Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur