PEERLESS SmartMount ST 630P Mode d’emploi

Max UL Load Capacity: 80 lb (36.3 kg)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 04-27-05 SHEET #: 201-9421-7 01-12-06

Features:

• Fits 10" to 24" LCD flat panel screens

• One-touch tilt for effortless positioning and adjustment of the screen

Installation and Assembly:

Universal Tilt Wall Mount for 10" - 24" LCD Flat Panel

Screens

Models: ST 630P, ST 630P-S, ST 630, ST 630-S

This product is intended for use with UL

Listed products and must be installed by a

qualified professional installer.

2 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-7 01-12-06

Note: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

•studfinder("edgetoedge"studfinderisrecommended)

•phillipsscrewdriver

•drill

•1/4" bit for concrete and cinder block wall

•1/2" bit for metal stud wall

•5/32" bit for metal or wood stud wall

•level

Accessories

• Metal Stud Fastener Kit (ACC 215) (Not evaluated by UL)

• VideoConferencingShelf(ACC 309) (Not evaluated by UL)

• Accessory Shelves (PM 600, PM 610) (Not evaluated by UL)

• Donotbegin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please

callPeerless customer careat1-800-729-0307.

• Thisproduct should only be installed byaqualified professional.

• Makesurethat the wall will safely support the combined load of the equipment and all attached hardware and compo-

nents.

• Neverexceedthe Maximum UL Load Capacity of 80 lb (36.3 kg).

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgeto edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrews firmly, but donot overtighten. Overtightening can damagethe items, greatly reducing theirholding

power.

WARNING

Table of Contents

Parts List..............................................................................................................................................................................3

Installation to Single Wood Stud Wall...................................................................................................................................4

Installation to Solid Concrete or Cinder Block .......................................................................................................................5

Attaching Adapter Plate to Flat Panel Screen ......................................................................................................................6

InstallingandRemovingFlatPanelScreen ...........................................................................................................................7

Adjusting the Tilt Angle of the Flat Panel Screen..................................................................................................................7

Forcustomer care call (800) 729-0307 or (708)865-8870.

3 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-7 01-12-06

GC D E F

ST 630P ST 630P-S ST 630 ST 630-S

Description Qty Part # Part # Part # Part #

Aadapter plate 1 095-1346 095-4346 095-1346 095-4346

Btilt assembly 1 095-0359 095-0360 095-0359 095-0360

CAlligator® anchor 2 590-0097 590-0097 590-0097 590-0097

DM4 x 10 mm phillips screw 4 504-9012 504-9012 504-9012 504-9012

EM4 x 20 mm phillips screw 4 504-9020 504-9020 504-9020 504-9020

Fretaining spacer 4 590-5005 590-5005 590-5005 590-5005

G#14 x 2-1/2" hex head wood screw 2 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03

HM5 x 6 mm screw 1 520-1023 520-1023 520-1114 520-1114

Isecurity driver 1 560-1133 560-1133

Parts List

4 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-7 01-12-06

Installation to Single Wood Stud Wall

1Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based

on its edges, draw a vertical line down the stud’s center. Place tilt assembly (B) on wall as a template, making sure

that the two mounting holes are over the stud centerline. Level tilt assembly, and mark the center of the two holes.

Drill two 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the tilt assembly is level, secure it using two

#14 x 2-1/2" wood screws (G) as shown.

Skip to step 2 on page 6.

• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and

components.

WARNING

• Tighten wood screws so that tilt assembly is firmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highly recommended.

• Hardwareprovided is for attachment ofmount through standard thickness drywallorplaster into wood studs. Installers

areresponsible to providehardware for other typesof mounting situations.

WARNING

5 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-7 01-12-06

Installation to Solid Concrete or Cinder Block

1Make sure that tilt assembly (B) is level, use it as a

template to mark two mounting holes. Drill two 1/4"

(6 mm) dia. holes to a minimum depth of 2-1/2"

(64 mm). Insert anchors (C) in holes flush with wall

as shown (right). Place tilt assembly over anchors

and secure with two #14 x 2-1/2" screws (G). Level,

then tighten all fasteners.

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and

components.

WARNING

CUTAWAY VIEW

INCORRECT

concrete

surface

Drill holes and insert anchors (C).

CORRECT

Place assembly (B)over anchors (C) and secure with screws (G).

Tighten all fasteners.

wall

plate

plaster/

drywall

concrete wall plate concrete

plaster/

drywall

• Always attach concrete expansion anchors directly to

load-bearingconcrete.

• Neverattach concrete expansion anchorsto concrete

coveredwith plaster,drywall, or other finishingmate-

rial.If mounting to concrete surfacescoveredwith a

finishingsurface isunavoidable,the finishingsurface

must be counterbored asshown below. Be sure

concreteanchors do not pull away from concrete

whentightening screws. If plaster/drywall is thicker

than 5/8", custom fasteners must be supplied by

installer.

WARNING

• Tighten screws so that wall plate is firmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

CINDERBLOCK

SOLID

CONCRETE

6 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-7 01-12-06

*For screens with a hole

pattern in a pocket,

spacers (F) go between

adapter plate (A) and

screen.

FORVESA®75MOUNTINGPATTERN:

Chooseholepattern asshown below.Attachadapter

plate (A) to back of screen using four M4 x 10 mm

screws(D) asshown below.

*Note: If hole pattern is in a pocket, attach adapter

plate (A) to back of screen using four M4 x 20 mm

screws(E)andfourretainingspacers(F)asindicated

below.

Attaching Adapter Plate to Flat Panel Screen

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

FORVESA100MOUNTINGPATTERN:

Chooseholepattern asshown below.Attachadapter

plate (A) to back of screen using four M4 x 10 mm

screws(D) asshown below.

7 of 7 ISSUED: 04-27-05 SHEET #: 201-9421-7 01-12-06

Attach screen to tilt assembly (B). Tighten M5 x 6

mm screw (H) to lock screen to tilt assemby.

Note: For security models, use security driver (I) to

tighten M5 x 6 mm screws (H).

Toremove screen frommount,loosen screw (H)and

lift screen off of mount.

Installing and Removing Flat Panel Screen

SCREEN

• Do not lift more weight than you can handle. Use

additionalman power ormechanical lifting equipment

to safely handle placement of the screen.

• Failure to lock adapter plate (A) with screw (H) can

cause screen to come off mount if hit accidentally.

• Do not tighten screws with excessive force.

Overtighteningcan causedamageto mount. Tighten

screws to 20 in. • lb (2.26 N.M.) maximum torque.

CAUTION

WARNING

fig. 3

PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

Adjust tension knob on right side of mount shown in

figure 4 to desired tension to balance your screen

size and weight.

Note: Ifknobis inaccessible, remove screen from

mount, adjust tension knob to desired tension to

balance your screen size and weight, and reattach

screen to mount as stated in step 3.

Push or pull from top or bottom of screen to adjust

tilt as shown in figure 4. The tilt can be adjusted to a

maximumof 15° forward or 5° backward.

Adjusting the Tilt Angle of the Flat Panel Screen

• Becareful not to pinch fingers whenpushingscreen

fromthe bottom.

CAUTION

• Do not tighten screws with excessive force.

Overtighteningcan causedamageto mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

fig. 4

TENSIONKNOB

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels PEERLESS Support et étagère

PEERLESS

PEERLESS ACC951 Mode d’emploi

PEERLESS

PEERLESS DS-VL-H018 Mode d’emploi

PEERLESS

PEERLESS SF 24D Mode d’emploi

PEERLESS

PEERLESS SmartMount ST 635 Mode d’emploi

PEERLESS

PEERLESS SmartMount RTFPA45 Mode d’emploi

PEERLESS

PEERLESS SlimLine MOWV241/BK Manuel utilisateur

PEERLESS

PEERLESS ST 640 Mode d’emploi

PEERLESS

PEERLESS HCACC502 Manuel utilisateur

PEERLESS

PEERLESS LWB375 Mode d’emploi

PEERLESS

PEERLESS SP730P Mode d’emploi

PEERLESS

PEERLESS IMC 18 Mode d’emploi

PEERLESS

PEERLESS PLA 50-UNL Mode d’emploi

PEERLESS

PEERLESS VPM 25-J Mode d’emploi

PEERLESS

PEERLESS SA761PU Mode d’emploi

PEERLESS

PEERLESS MOD-FPSKIT150 Mode d’emploi

PEERLESS

PEERLESS SmartMount D-FPF-320 Mode d’emploi

PEERLESS

PEERLESS SmartMount ST 635 Mode d’emploi

PEERLESS

PEERLESS SUT632P Mode d’emploi

PEERLESS

PEERLESS PM 47 Mode d’emploi

PEERLESS

PEERLESS LCC 18 Mode d’emploi

PEERLESS

PEERLESS Paramount PSP2 Mode d’emploi

PEERLESS

PEERLESS Solid-Point PLCM 2 Mode d’emploi

PEERLESS

PEERLESS Paramount PPF Mode d’emploi

PEERLESS

PEERLESS IM740P Mode d’emploi

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur