PEERLESS ACC605 Mode d’emploi
1 of 4 ISSUED: 11-22-10 SHEET #: 120-9095-2 12-01-10
Parts List
Description Qty. Part Numbe
r
Qty. Part Numbe
r
A
#14 x 2.5" hex head wood screw 4 5S1-015-C04 6 5S1-015-C04
B1/4 - 20 x 2.5" phillips screw 4 520-9521 6 520-9521
Cconcrete anchor 4 590-0320 6 590-0320
D1/4 -20 toggler 4 560-9708 6 560-9708
E1/4" flat washe
r
4 540-9440 6 540-9440
Model: ACC605, ACC610
Installation and Assembly:
Mounting Hardware for IWB600-SB, and IWB600-UNIV
Installation to Wood Stud Wall..............................................................Page 2
Installation to Concrete or Cinder Block Wall.....................................Page 3
Installation to Metal Stud Wall..............................................................Page 4
ABC D E
ACC605ACC610
NOTE: Use IWB600-SB, and IWB600-UNIV Instruction sheets to determine
mounting hardware locations
2 of 4 ISSUED: 11-22-10 SHEET #: 120-9095-2 12-01-10
Installation to Wood Stud Wall
Use a stud nder to locate the edges of the studs. Use of an edge-to-edge stud nder is highly recommended.
Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template. Level
plate, and mark the center of the mounting holes. Make sure that the mounting holes are on the stud center lines.
Drill 5/32" (4 mm) dia. holes 2.5" (64 mm) deep. Make sure that the wall plate is level, secure it using
#14 x 2.5" hex head wood screws (A) as shown.
A
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is rmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud nder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations.
1
WALL PLATE
WOOD STUD
WARNING
3 of 4 ISSUED: 11-22-10 SHEET #: 120-9095-2 12-01-10
1
WALL PLATE
CONCRETE
CINDER BLOCK
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
dry wall
plaster/
dry wall
concrete concrete
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
• Tighten screws so that wall plate is rmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly to
load-bearing concrete.
• Never attach concrete expansion anchors to concrete
covered with plaster, drywall, or other nishing mate-
rial. If mounting to concrete surfaces covered with a
nishing surface is unavoidable, the nishing surface
must be counter bored as shown below. Be sure con-
crete anchors do not pull away from concrete when
tightening screws. If plaster/drywall is thicker than
5/8" (16 mm), custom fasteners must be supplied by
installer.
For Concrete Surfaces use wall plate as a template,
level and mark center of mounting holes. Drill 5/16" (8
mm) dia. holes to a minimum depth of 2.5"
(64 mm). Insert anchors (C) into holes ush with wall,
place wall plate over anchors and secure with #14 x 2.5”
hex head wood screws (A) as shown right. Make sure
wall plate is level, and tighten all fasteners.
1
3
2
C
Drill holes and insert anchors (C).
Place plate over anchors (C) and secure with wood screws (A).
Tighten all fasteners.
C
concrete
surface
Installation to Concrete or Cinder Block Wall
A
C
mounting plate
A
WARNING
WARNING
4 of 4 ISSUED: 11-22-10 SHEET #: 120-9095-2 12-01-10
D
∅ 1/2"
(13 mm)
FOR METAL STUD WALLS ONLY: Drill four 1/2"
(13mm) dia. holes through drywall and studs at lo-
cations corresponding to wall plate. Insert togglers
(D) as shown below.
• Product must be mounted through drywall that has a
minimum thickness of 1/2" and into metal studs, 26
gauge or heavier.
• Make sure that togglers are anchored into the center
of the studs as shown in gure 1. The use of an
"edge to edge" stud nder is highly recommended.
WARNING
Rotate toggler (D)
clockwise to wedge it
against inside walls
of metal stud.
Push into hole.
Pivot end of
toggler (D).
Slide plastic cap
forward while pulling
back rmly on ring.
Break off excess.
D
Align wall plate with
hole in wall and fas-
ten using
1/4-20 x 2.5" screw
(B) and 1/4"
washer (E).
WALL PLATE
B
E
Installation to Metal Stud Wall
1-2
1-1
1-3
1-4
1
1-6
1-5
© 2010, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels PEERLESS Support et étagère
PEERLESS
PEERLESS SmartMount D-FPF-320 Mode d’emploi
PEERLESS
PEERLESS SR1G Mode d’emploi
PEERLESS
PEERLESS SmartMount ST 635 Mode d’emploi
PEERLESS
PEERLESS Solid-Point PLCM 1 CP Mode d’emploi
PEERLESS
PEERLESS WMJ 018 Mode d’emploi
PEERLESS
PEERLESS PANA-85WM Mode d’emploi
PEERLESS
PEERLESS PLAV 70 Mode d’emploi
PEERLESS
PEERLESS SOLID POINT PLCM 1 Mode d’emploi
PEERLESS
PEERLESS SF 24D Mode d’emploi
PEERLESS
PEERLESS PARAMOUNT PA730 Mode d’emploi
PEERLESS
PEERLESS PARAMOUNT PF640 Mode d’emploi
PEERLESS
PEERLESS MIS488 Mode d’emploi
PEERLESS
PEERLESS SlimLine MOWV241/BK Manuel utilisateur
PEERLESS
PEERLESS WSP 420 Manuel utilisateur
PEERLESS
PEERLESS PRG-1 Mode d’emploi
PEERLESS
PEERLESS WSP 490 Mode d’emploi
PEERLESS
PEERLESS PED 410 Mode d’emploi
PEERLESS
PEERLESS HDS-S Mode d’emploi
PEERLESS
PEERLESS DS 35 Mode d’emploi
PEERLESS
PEERLESS DST360 Mode d’emploi
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
