PEERLESS SP730P Mode d’emploi

Max ULLoad Capacity: 25 lb (11.3 kg)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06

Installation and Assembly:

LCD Screen Long Pivot Wall Mount

Models: SP730P, SP730P-S, D-LPL-100, RTLPL-100S

Features:

•Fits 10" - 22" LCD screens

• Arm extends up to 6" from wall or folds flat to save space

• Supports screens with VESA®75 or 100 mounting holes

• Featuresball jointat thescreen foradditional side-to-sideswivel

andupwardand downward tilt

All manuals and user guides at all-guides.com

all-guides.com

2 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06

Forcustomer care call(800) 729-0307 or (708) 865-8870.

Table of Contents

Parts List.............................................................................................................................................................................. 3

Installation to Wood Stud Wall ............................................................................................................................................. 4

Installation to Solid Concrete and Cinder Block .................................................................................................................... 5

Tools Needed for Assembly

• studfinder ("edgeto edge"stud finderis recommended)

• phillipsscrewdriver

• drill with 1/4" and 5/32" drill bits

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call

Peerless customer service at 1-800-729-0307.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never mount this product to a metal stud wall construction unless the stud can be verified to be constructed of 25

gauge steel minimum, the drywall is 1/2" thick minimum and you obtain and use the Peerless accessory kit for metal

studs.

• Neverexceed the MaximumULLoadCapacity.

• If mounting to wood wall stud wall construction, make sure that mounting screws are anchored into the center of the

studs. Use of an "edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power. See suggested torque values where applicable within these instructions.

WARNING

Accessories

• Metal StudAccessory Kit (ACC 908) (Not evaluated by UL)

Notes:

• Read entire instruction sheet before you start installation and assembly.

• Screen must be attached to the mount to enable tilting.

All manuals and user guides at all-guides.com

3 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06

D-LPL-100

SP730P SP730P-S

Description Qty. Part # Part #

Awall arm 1 095-0383-B 095-0383-S

Bcord management clip 2 590-1264 590-2164

C3/16" allen wrench 1 560-0071 560-0071

D#14 x 2-1/2" flat head wood screw 2 520-1202 520-2165

EAlligator® anchor 2 590-0097 590-0097

FM4 x .7 x 12 mm phillips screw 4 504-9013 504-2013

GM4 x .7 x 20 mm phillips screw 4 504-9020 504-2014

Hretaining spacer 4 590-5005 590-5003

I5 mm allen wrench 1 560-9640 560-9640

Parts List

RTLPL-100S

All manuals and user guides at all-guides.com

4 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06

Installation to Wood Stud Wall

Using a stud finder, locate and mark the edges of the wood stud used in mounting this product. Use of an edge to

edge stud finder is highly recommended. Use a level to draw a vertical line down the center of the stud. Use wall

plate as template to mark center of holes along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (65 mm)

deep.Attach wall arm assembly (A) to wall using two #14 x 2.5" flat head wood screws (D) as shown.

Skip to step 2 on page 6.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardwareandcomponents.

WARNING

• Tightenscrews sothat wallplate isfirmly attached,but donot overtighten.Overtightening can damage the screws,

greatlyreducingtheirholdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is

highlyrecommended.

WARNING

WOOD

STUD

WALL

All manuals and user guides at all-guides.com

5 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06

Installation to Solid Concrete and Cinder Block

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.

It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid

breakingout the back of thehole when enteringa voidor cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardwareandcomponents.

WARNING

Level and use wall plate as template to mark center

of holes. Drill two 1/4" (6 mm) dia. holes to a

minimum depth of 2" (51 mm). Insert anchors (E) in

holes flush with wall as shown in fig 1.3. Place wall

arm(A) over anchorand secure with wood screw(D)

as shown in figures 1.4 and 1.6. Make sure wall arm

is level, and tighten all fasteners. See figure 1.5.

• Concrete anchorsare notintendedforattachment to

concretewall covered witha layer ofplaster,drywall,

orother finishing material asshown below.Ifmounting

toconcrete wall coveredwith plaster/drywall is

unavoidable,plaster/drywall (up to5/8" thick) must be

counterboredas shown below.Besure concrete

anchorsdo not pullaway from concretewhen tighten-

ing screws. If plaster/drywall is thicker than

5/8", custom fasteners must be supplied by installer.

WARNING

concrete

wall

Drill holes

and insert

anchors.

Place wall

plate over

anchor and

secure with

screw.

Tighten all

fasteners.

WALLPLATE

fig 1.3

fig 1.4

fig 1.5

CUTAWAYVIEW

CORRECT

concrete

plaster/

drywall

INCORRECT

concrete

plaster/

drywall

• Tighten screws so that wall plate is firmly attached,

butdonotovertighten. Overtightening can damage the

screws,greatlyreducing their holdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

fig 1.6

All manuals and user guides at all-guides.com

6 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06

Insert two M4 x 12 mm screws (F) into top two holes

ofscreen, leaving approximately 1/4" ofexposed

thread. Hook screws onto keyslots of adapter plate

as indicated in figures 2.1 and 2.2.

*Note: If hole pattern is in a pocket, insert two M4 x

20 mm screws (G) with two retaining spacers (H)

into top two holes of screen as indicated right.

fig. 2.1

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

Note: Toadd security, orderACC 918 forsecurity

screws.Refer toACC 918 instruction sheet for

installing security screws.

1/4"

*For screens with a

hole pattern in a

pocket, spacers (H)

go between adapter

plate and screen.

FOR VESA®75

MOUNTINGPATTERN: FOR VESA100

MOUNTINGPATTERN:

fig. 2.2

Screen may appear

slightlydifferentthan

illustrated

Insert one M4 screw (F or G) through bottom hole of

adapterplateas shown infigure3.1.

fig. 3.1

F or G

ADAPTER

PLATE

All manuals and user guides at all-guides.com

all-guides.com

7 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06

Bdetail 1

Route cords through center of cord management clip (B). Next, attach cord management clip (B) to adapter plate

using M4 screw (F or G) as shown in detail 1. Tighten all four screws (F or G).

Note:An additional cord management clip (B) was added for additional cords. If you want to use this additional clip,

remove the opposite bottom screw and repeat this step on opposite side of adapter plate.

F or G

All manuals and user guides at all-guides.com

8 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06

If more or less tension is desired in the arm pivot points, do the following:

• To increase tension, turn socket screw clockwise with 3/16" allen wrench (C).

• To reduce tension, turn socket screw counter-clockwise with allen wrench (C). Do not turn more than half a turn.

PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

NOTE: Adjustmentpoints(socket screws) are factory torquedfor optimal performance. This factory torque setting is

recommended to prevent the screen from slipping over time. Ifmore or lesstension isdesired follow thisoptional

step. You may not achieve optimal torque value if factory torque settings are adjusted.

If more or less tension is desired in tilt mechanism, remove snap caps as shown in detail 2. Insert a flat head screw

driver into slot and pry cap away from tilt mechanism. To adjust tilt, simply tighten or loosen socket screw no more

than half a turn using 5 mm allen wrench (I).To adjust roll, simply tighten or loosen 10-32 nylock nut.

SNAPCAP

SOCKET

SCREW

10-32NYLOCKNUT

detail 2

OPTIONAL

SLOT

• Donotremovescreworloosenscrewuntil it is nolongerengagedwiththemount.Doingsomaycausethescreentofall.

WARNING

SOCKETSCREW

All manuals and user guides at all-guides.com

Capacité de charge maximale :

11,3 kg (25 lb)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 06-10-05 SHEET #: 095-9225-7 08-28-06

Installation et assemblage :

Monture réglable pour fixation d’écran à cristaux

liquides sur un mur/une armoire

Modèles :SP730P, SP730P-S, D-LPL-100, RTLPL-100S

Caractéristiques :

•Convient aux écrans à cristaux liquides de 25 à 55 cm (10 à 22 po)

•Le bras d’étend à une distance maximale de 15 cm (6 po) du mur et

se replie à plat pour économiser de la place

•Convient aux écrans dotés de trous de montage VESA®75 ou 100

•L’écran comporte un joint à rotule qui accroît le pivotement latéral et

l’inclinaison vers le haut et vers le bas.

All manuals and user guides at all-guides.com

10 of 24 ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06

Pourle serviceà laclientèle, appelezle 011+1+(708)865-8870.

Outils nécessaires pour l’assemblage

• localisateur de montants (le localisateur de montants « bord à bord » est recommandé)

• tourneviscruciforme

• perceuse à mèches de 6,35 mm (1/4 po) et 3,96 mm (5/32 po)

Accessoires

• Kit d’accessoires pour montants métalliques (ACC 908)

Table des matières

Liste des pièces ..................................................................................................................................................................11

Installation sur un mur à montants en bois ......................................................................................................................... 12

Installation sur du béton plein ou un bloc de béton de mâchefer ......................................................................................... 13

•Ne commencez pas à installer votre produit Peerless avant d’avoir lu et assimilé les instructions et les mises en

garde contenues dans cette fiche d’instructions. Pour toute question concernant les instructions ou les mises en

garde,appelez leservice à la clientèle de Peerless au011+1+(708) 865-8870.

•Ceproduit ne doit être installé que par une personne ayant de bonnes aptitudes en mécanique,expérimentée en

travauxde construction de base, et démontrant une parfaite compréhension de ces instructions.

•Assurez-vousque lasurface desupport pourrasoutenir sans difficulté la charge combinée de l’équipement, de toute

sa visserie et de tous ses composants.

•Ne montez jamais ce produit sur un mur à montants métalliques sans vous assurer que le montant est en acier de

calibre 25 au minimum, que la cloison sèche a au moins 12,5 mm (1/2 po) d’épaisseur et sans utiliser le kit

d’accessoires Peerless pour montants métalliques.

•Ne dépassez jamais la capacité de charge maximum.

•Si vous effectuez le montage sur un mur à montants en bois, assurez-vous que les vis de montage sont ancrées au

centre des montants. L’usage d’un localisateur « bord à bord » est fortement conseillé.

•Pourlever etpositionner l’équipement en toute sécurité, faites-vous toujours aider par une autrepersonne ouutilisez

unmatériel de levage mécanique.

• Serrez fermement les vis, mais sans excès. Un serrage excessif peut endommager les éléments et en réduire

considérablementle pouvoirde maintien. Référez-vous aux couplesde serragesuggérés dans ces instructions, dans

les cas applicables.

AVERTISSEMENT !

Remarques :

• Lisez entièrement la fiche d’instructions avant de commencer l’installation et l’assemblage.

• L'écrandoit être fixé au bâti pour permettre l'inclinaison.

All manuals and user guides at all-guides.com

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels PEERLESS Support et étagère

PEERLESS

PEERLESS SUT632P Mode d’emploi

PEERLESS

PEERLESS ACC-V800X Mode d’emploi

PEERLESS

PEERLESS SGLS01 Mode d’emploi

PEERLESS

PEERLESS Slimline OP-LWB 530 Mode d’emploi

PEERLESS

PEERLESS IWB600-WB Manuel utilisateur

PEERLESS

PEERLESS LDS 1920U Mode d’emploi

PEERLESS

PEERLESS WSP 420 Manuel utilisateur

PEERLESS

PEERLESS VPM 25-W Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PA740 Manuel utilisateur

PEERLESS

PEERLESS SmartMount SA770PU Mode d’emploi

PEERLESS

PEERLESS SmartMount SP740P Mode d’emploi

PEERLESS

PEERLESS SmartMount SA750P Mode d’emploi

PEERLESS

PEERLESS WSP 716 Manuel utilisateur

PEERLESS

PEERLESS DS495 Mode d’emploi

PEERLESS

PEERLESS FPZ-655 Mode d’emploi

PEERLESS

PEERLESS Paramount PP730 and assembly Mode d’emploi

PEERLESS

PEERLESS SmartMount RTFPA45 Mode d’emploi

PEERLESS

PEERLESS IMC 18 Mode d’emploi

PEERLESS

PEERLESS PARAMOUNT PF640 Mode d’emploi

PEERLESS

PEERLESS ESA746PU Mode d’emploi

PEERLESS

PEERLESS PJF2-UNV Mode d’emploi

PEERLESS

PEERLESS SAL730P Mode d’emploi

PEERLESS

PEERLESS RTPLA 50 Mode d’emploi

PEERLESS

PEERLESS SlimLine MOWV241/BK Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur