Monoprice 43363 Manuel utilisateur
Joule 3D Printer DIY Assembly Kit
P/N 43363
User's Manual
2
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this
manual in a safe place for future reference.
•This device is intended for indoor use only.
•Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the
device. If moisture does get in or on the device, immediately remove it from its power source and allow it to fully dry before
reapplying power.
•Do not touch the device, the power cord, or any other connected cables with wet hands.
•Do not install this device on an unstable surface where it could fall and cause either personal injury or damage to the device
and/or other equipment.
•Do not expose this device to excessive vibration, extreme force, shock, or fluctuations in temperature or humidity.
•Do not expose this device to excessively high temperatures. Do not place it in, on, or near a heat source, such as a fireplace,
stove, radiator, etc. Do not leave it in direct sunlight.
•Do not place or install this device in an area where it can be exposed to excessive amounts of dust, humidity, oil, smoke, or
combustible vapors.
•Use only in a well-ventilated area. Do not use in close, confined spaces.
•Prior to operation, check the unit and power cord for physical damage. Do not use if physical damage has occurred.
•Before plugging the unit into a power outlet, ensure that the outlet provides the same type and level of power required by the
device.
3
•This device uses a grounded power cord and requires a ground connection for safe operation. Ensure that the power source has
a proper ground connection. Do not modify the plug or use a "cheater" plug to bypass the ground connection.
•Unplug this device from the power source when not in use.
•Take care to prevent damage to the power cord. Do not allow it to become crimped, pinched, walked on, or become tangled
with other cords. Ensure that the power cord does not present a tripping hazard.
•Never unplug the unit by pulling on the power cord. Always grasp the connector head or adapter body.
•Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth
with warm water.
•This device has no user serviceable parts. Do not attempt to open, service, or modify this device.
•Take care to avoid touching hot parts, including heat blocks, extruder nozzle, extruded filament, and the heated build plate.
•Do not wear gloves when operating or repairing to avoid entanglement.
•Keep the printer and all accessories out of reach of children.
•Do not reach inside the printer during operation.
•Always allow the printer and extruded filament to cool before reaching inside.
•Ensure that the printer is turned off and unplugged from its power source before making repairs or performing service.
4
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second
to none. If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website www.monoprice.com or via email at
support@monoprice.com. Check the website for support times and links.
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged,
please contact Monoprice Customer Service for a replacement.
1x Printer Base
1x Screen Kit
1x Extruder Kit
1x Z-axis Passive Block
5
1x X-axis Tensioner
1x Z-axis Motor Kit
1x X-axis Limit Switch Kit
1x XE-axis Kit
1x Z-axis Profile (left)
1x Z-axis Profile (right)
1x Gantry Profile
1x X-axis Profile
6
1x T-shaped Screw Rod
1x Filament Rack
1x Spool Holder and Nut
2x Gantry Cover
1x Synchronous Belt
1x Scraper
1x Cable Tie
1x Needle
7
1x microSD™ Card
and Card Reader
2x M6 Pneumatic Joint
1x AC Power Cord
1x Toolkit
(1x Screwdriver, 1x Open-End
Wrench, 2x Allen Wrenches)
1x Nozzle
1x Screen Bracket
2x M4x20 Hexagon Socket
Countersunk Head Screw
2x M4x6 Hexagon Socket Flat
Round Head Screw
8
6x M5x14 Hexagon Socket Flat
Round Head Screw
2x M4x8 Hexagon Socket Head
Spring Washer Combination
Screw
5x M5x45 Hexagon Socket
Head Spring Washer
Combination Screw
5x M5x25 Hexagon Socket
Head Spring Washer
Combination Screw
6x M4 T-Nuts
4x M4x12 Hexagon Socket Head
Spring Washer Combination
Screw
1x Roll PLA Filament
9
PRODUCT OVERVIEW
1. XE-axis Kit
2. X-axis Limit Switch
3. Build Plate
4. Y-axis Tensioner
5. Extruder Kit
6. Filament Rack and Spool Holder
7. Z-axis Passive Block
8. X-axis Tensioner
9. Screen
10. Control Knob
10
11. Printer Base
12. Power Supply
13. Voltage Switch
14. Y-axis Limit Switch
15. Y-axis Motor
16. E-axis Motor
17. X-axis Motor
18. Coupling
19. Z-axis Limit Switch
20. Z-axis Motor
21. Power Switch and Socket
Table des matières
Autres manuels Monoprice Imprimante 3D
Monoprice
Monoprice MP Mibi Delta Manuel utilisateur
Monoprice
Monoprice MP Voxel Manuel utilisateur
Monoprice
Monoprice maker architect 13861 Manuel utilisateur
Monoprice
Monoprice MP10 Manuel utilisateur
Monoprice
Monoprice Select Mini Pro Manuel utilisateur
Monoprice
Monoprice 15365 Manuel utilisateur
Monoprice
Monoprice Maker Ultimate 2 Manuel utilisateur
Monoprice
Monoprice 13860 Manuel utilisateur
Monoprice
Monoprice MP CADET Manuel utilisateur
Monoprice
Monoprice MP Mini Delta V2 Manuel utilisateur
Monoprice
Monoprice Delta Pro Manuel utilisateur
Monoprice
Monoprice 30525 Manuel utilisateur
Monoprice
Monoprice MP Mini Delta V2 Manuel utilisateur
Monoprice
Monoprice 21711 Manuel utilisateur
Monoprice
Monoprice MP Voxel Pro Manuel d'instructions
Monoprice
Monoprice 33820 Manuel utilisateur
Monoprice
Monoprice extrusion i3 13860 Manuel utilisateur
Monoprice
Monoprice 21824 Manuel utilisateur
Monoprice
Monoprice MP Mini Delta V2 Manuel utilisateur
Monoprice
Monoprice 35435 Manuel utilisateur
