Monoprice MP Voxel Pro Manuel d'instructions

MP Voxel Pro Fully Enclosed 3D Printer

P/N 44091

Quick User Guide

ONLINE SUPPORT

Monoprice™ is pleased to provide free online support. For order related issues, contact the

Customer Service department through the Live Chat link on our website

www.monoprice.com or via email at sup[email protected]

For technical issues, contact the Technical Support department through the online chat

button on our website www.monoprice.com or by sending an email to

[email protected]

Check the website for support times and links.

GETTING STARTED

1. Install the FlashPrint software package. The FlashPrint installation package can be

found on the USB Flash Drive included with the printer. You can also download it

from the product page on the website. To locate the download file, navigate to

https://www.monoprice.com, then type 44091 into the search bar, and hit ENTER.

Scroll to the bottom of the page to find the Support Files section, which has the full

manual, the FlashPrint software package, and any other related files.

2. Ensure that the Power Switch on the printer is in the OFF (O) position.

3. Plug one end of the included AC Power Cord into the Power Connector on the

printer, then plug the other end into a nearby AC power outlet.

4. Flip the Power Switch on the printer to the ON (I) position.

5. Although the printer was fully calibrated at the factory, it may have gone out of

calibration during the shipping process, so it is a good idea to do at least a single-

point calibration. On the Touchscreen Interface, touch Maintain > Calibration >

Normal Mode. Follow the on-screen instructions for the first point. You can then

either exit or finish the full Nine Point Auto Calibration. For more information, refer

to the

USER INTERFACE > Calibration

section in the User's Manual.

6. Open the Filament Door on the printer, then place a spool of filament on the

Filament Spool Holder.

7. Remove the Filament Intake Cover, then insert the end of the filament into the

filament intake. Push the filament into the feeding wheel until some resistance is

felt.

8. On the Touchscreen Interface, touch Prepare > Filament > Load, then follow the on-

screen instructions to load the filament.

9. The USB Flash Drive included with the printer has sample models preloaded. Insert

the USB Flash Drive into the USB Port on the printer. On the Touchscreen Interface,

touch Build > USB Device. The system will display the files on the flash drive.

Touch a model image to display the file details, then touch the Build button to start

printing the file.

10. When the print is finished, wait for the printer and model to fully cool down to

room temperature. Once they are fully cooled, remove the Removable Build Plate,

then slightly bend the plate to detach the model.

REGULATORY COMPLIANCE

Notice for FCC

This device complies with Part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

Modifying the equipment without Monoprice's authorization may result in the equipment

no longer complying with FCC requirements for Class B digital devices. In that event, your

right to use the equipment may be limited by FCC regulations, and you may be required to

correct any interference to radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement for FCC

Caution

This FCC Part 15 radio device operates on a non-interference basis with other devices

operating at this frequency. Any changes or modification to said product not expressly

approved by Monoprice, including the use of non-approved antennas, could void the user's

authority to operate this device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

EU/UK Compliance

Hereby, Monoprice Inc. declares that the radio equipment type 3D Printer is in compliance

with Directive 2014/53/EU and Radio Equipment Regulations 2017. The full text of the

declaration of Conformity is available at the following internet address:

https://www.monoprice.eu/

The information required by EU radio equipment directive / UK radio equipment

regulations related to the frequency band(s) and the maximum radio-frequency power

transmitted:

Frequency: 2400 - 2497 MHz; Max Power: 7±1dBm

Disposal and Recycling Information

The symbol indicates that this product should be disposed of separately from regular

household waste streams. It is your responsibility to dispose of this and other electrical and

electronics products via designated collection facilities appointed by the government or

local authorities. Correct disposal and recycling will help prevent potential negative

consequences to the environment and human health. For more detailed information about

the disposal of your unwanted product, please contacts your local authorities, waste

disposal service, or the shop where you purchased the product.

Monoprice™, Voxel™, the Voxel logo, and all Monoprice logos are trademarks of

Monoprice Inc.

Wi-Fi® and Wi-Fi Alliance® are registered trademarks of Wi-Fi Alliance.

Polar Cloud™ is a trademark of Polar3D.

Autres manuels pour MP Voxel Pro

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Monoprice Imprimante 3D

Monoprice

Monoprice MP CADET Manuel utilisateur

Monoprice

Monoprice cadet Mode d’emploi

Monoprice

Monoprice maker architect 13861 Guide de dépannage

Monoprice

Monoprice Maker Select Plus IIIP Manuel utilisateur

Monoprice

Monoprice 43363 Manuel utilisateur

Monoprice

Monoprice Maker Ultimate 2 Manuel utilisateur

Monoprice

Monoprice extrusion i3 13860 Manuel utilisateur

Monoprice

Monoprice MP Mini Delta V2 Manuel utilisateur

Monoprice

Monoprice MP Maker Pro Mk.1 Manuel utilisateur

Monoprice

Monoprice MP Mini Delta V2 Manuel utilisateur

Monoprice

Monoprice MP Voxel Manuel utilisateur

Monoprice

Monoprice MP10 Manuel utilisateur

Monoprice

Monoprice MP Delta Pro Manuel utilisateur

Monoprice

Monoprice MP Maker Pro Mk.1 Manuel utilisateur

Monoprice

Monoprice 13860 Manuel utilisateur

Monoprice

Monoprice MP Education Guider II Manuel utilisateur

Monoprice

Monoprice MP Mini SLA LCD Manuel utilisateur

Monoprice

Monoprice 30526 Manuel utilisateur

Monoprice

Monoprice Maker Ultimate 2 Manuel utilisateur

Monoprice

Monoprice Voxel 33820 Manuel utilisateur

Monoprice

Monoprice Delta Pro Manuel utilisateur

Monoprice

Monoprice MP Mibi Delta Manuel utilisateur

Monoprice

Monoprice Select Mini 3D Printer V2 Manuel utilisateur

Monoprice

Monoprice MP Voxel Pro Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur