Monoprice MP Mini Delta Manuel utilisateur

MONOPRICE

MP Mini Delta 3D Printer

P/N 21666

User's Manual

CONTENTS

SAFETY WARNINGS AND GUIDELINES.......................................................................................................................................3

INTRODUCTION................................................................................................................................................................................................4

FEATURES..............................................................................................................................................................................................................4

CUSTOMER SERVICE....................................................................................................................................................................................5

PACKAGE CONTENTS.................................................................................................................................................................................5

PRODUCT OVERVIEW.................................................................................................................................................................................6

USING THE MENU SYSTEM....................................................................................................................................................................6

PRINTER SETUP................................................................................................................................................................................................. 7

WI-FI SETUP.........................................................................................................................................................................................................9

SOFTWARE INSTALLATION AND SETUP..................................................................................................................................10

Installing Cura for Windows.........................................................................................................................................................10

Repetier-Host............................................................................................................................................................................................ 17

TECHNICAL SUPPORT...............................................................................................................................................................................19

REGULATORY COMPLIANCE..............................................................................................................................................................19

Notice for FCC ..........................................................................................................................................................................................19

Notice for Industry Canada...........................................................................................................................................................19

SAFETY WARNINGS AND GUIDELINES

Be careful not to damage the yellow film on the build plate.

Do not remove the insulating tape on the extruder nozzle.

Take care to avoid touching hot parts, including heat blocks, extruder nozzle,

extruded filament, and the heated build plate.

Do not wear gloves when operating or repairing to avoid entanglement.

Keep the printer and all accessories out of reach of children.

Do not remove or disconnect the USB cable when printing from a computer.

Do not pull or twist the black cable at any time.

Do not force or tear anything when during unpacking and setup. This may cause

damage to the printer and/or its accessories.

Do not reach inside the printer during operation.

Always allow the printer and extruded filament to cool before reaching inside.

Ensure that the printer is turned off and unplugged from its power source before

making repairs or performing service.

Do not install this device on an unstable surface where it could fall and cause either

personal injury or damage to the device and/or other equipment.

Do not subject the product to extreme force, shock, or fluctuations in temperature

or humidity.

This device is intended for indoor use only.

Do not expose this device to water or moisture of any kind. Do not place drinks or

other containers with moisture on or near the device. If moisture does get in or on

the device, immediately unplug it from the power outlet and allow it to fully dry

before reapplying power.

Do not touch the device, the power cord, or any other connected cables with wet

hands.

Use only in a well-ventilated area. Do not use in close, confined spaces.

Prior to operation, check the unit and power cord for physical damage. Do not use if

physical damage has occurred.

Before plugging the unit into a power outlet, ensure that the outlet provides the

same type and level of power required by the device.

Unplug this device from the power source when not in use.

Take care to prevent damage to the power cord. Do not allow it to become

crimped, pinched, walked on, or become tangled with other cords. Ensure that the

power cord does not present a tripping hazard.

Never unplug the unit by pulling on the power cord. Always grasp the connector

head or adapter body.

INTRODUCTION

Thank you for purchasing this 3D printer from Monoprice! This printer features a single

extruder, which is capable of printing in PLA, ABS, and other materials. You can print from a

Windows® or Mac® PC using a USB connection or can print from 3D model files stored on a

microSD™card, without the need for a PC connection of any kind. This printer is easy to

setup and easy to use following the instructions in this manual.

FEATURES

Single extrusion print head

Can print PLA, ABS, and other materials

Open frame design for ease of use and maintenance

Includes 256MB microSD™card with Cura, Repetier-Host, and a sample 3D model

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering,

purchasing, and delivery experience is second to none. If you have any problem with your

order, please give us an opportunity to make it right. You can contact a Monoprice

Customer Service representative through the Live Chat link on our website

www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-

6pm PT) or via email at [email protected]

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service for a

replacement.

1x 3D printer

1x Filament holder

1x Plastic scraper

1x USB cable

1x MicroSD™card

1x Hex wrench

1x Power adapter

1x AC power cord (NEMA 5-15 to IEC 60320 C13)

PRODUCT OVERVIEW

1. Feed Mechanism

2. Extruder

3. Micro USB Port

4. DC Power Connector

5. Power LED Indicator

6. MicroSD™ Card Slot

7. Filament Holder Slots

USING THE MENU SYSTEM

The menu system is displayed on a lighted LCD screen.

The menu selection highlight or pointer is moved by pressing the top and bottom

buttons to the right of the display.

Pressing the top button moves the highlight/pointer to the left and up.

Pressing the bottom button moves the highlight/pointer to the right and down.

Pressing the top button while editing a value increases that value.

Pressing the bottom button while editing a value decreases that value.

Press the center button to activate the selected menu item or to save an edited

value.

PRINTER SETUP

Warning! Take care not to remove or damage the black PEI build mat on the build platform.

This mat is essential to ensure the 3D model properly adheres to the build platform during

printing. If this mat becomes damaged or wears out, replace it with painter's tape, Kapton®

tape, or ordinary masking tape.

Perform the following steps to prepare the printer for use.

1. Remove the printer from its packaging and place it on a flat, stable surface with

plenty of ventilation and a nearby AC power outlet.

2. Open the Accessories box and remove the Filament Holder. Slide

the tab at the flat end into the Filament Holder Slots (7) on the

rear of the printer frame.

3. Insert the included microSD™card into the MicroSD™ Card Slot (6)

on the side of the printer.

4. Plug the DC barrel connector on the included AC power adapter into the power

connector on the side of the printer. Next, plug the C13 end of the included AC

Power Cable into the C14 panel connector on the AC Power Adapter, then plug the

other end into a nearby AC power outlet.

5. Press the bottom button once to highlight the Temperature entry, then press the

center button to select it.

6. Press the center button to select the temperature value, then use the top and

bottom buttons to set the target temperature. Set it to 230°C for ABS filament or

set it to 195°C for PLA filament. Press the center button to save the target

temperature and begin heating the extruder.

7. While the printer is heating, open your filament. Using a pair of scissors or side

cutters, diagonally snip the end of the filament to make a point, as shown in the

images below. Place the spool on the Filament Holder.

8. Once the target temperature is reached, press the bottom button twice to select

the Back option, then press the center button to return to the previous menu page.

9. Press the bottom button to highlight the Move option, then press the center

button to enter the Move menu.

10. Press the bottom button three times to highlight the Extruder option, then press

the center button to select it. The Extruder option will have a red outline around it,

indicating that it is active.

11. While squeezing the lever on the Feed Mechanism, insert the

filament and push it into opening. Keep pushing until you feel

resistance. Release the lever on the Feed Mechanism.

12. Press the top button to feed filament into the printer. Allow the

motor to run until it stops feeding. Repeat this process until

filament starts to extrude out of the nozzle.

13. Using the included plastic scraper, clean the extruded filament from the nozzle and

build platform.

14. Press the center button to deselect the Extruder entry.

15. Press the bottom button twice to highlight the Exit entry, then press the center

button to return to the previous menu.

16. Press the top button twice to highlight the Print option, then press the center

button. The printer will read the contents of the microSD™card and display them on

screen.

17. Use the top and bottom buttons to highlight the cat.gcode file, then press the

center button to start printing the model.

Congratulations, your 3D printer is setup and you are printing your first model!

WI-FI SETUP

You can connect the printer wirelessly to a 2.4Ghz Wi-Fi® network to print models from

your Android™ or iOS® phone or tablet. Perform the following steps to setup the Wi-Fi

connection for your device.

1. Download the free MP 3D Printer WiFi Connect app from the Google Play Store or

from iTunes, depending on which type of mobile device you have.

2. Disconnect the USB cable from the printer. You cannot use USB and Wi-Fi

connections at the same time.

3. Power on the printer.

4. Start the MP 3D Printer WiFi Connect app.

5. The SSID of your Wi-Fi network should be displayed on screen. If a different SSID is

displayed, open your device's Wi-Fi settings and select the appropriate Wi-Fi

network.

6. Enter your wireless password.

7. Use the printer's buttons to navigate to the Move menu.

8. Press and hold the center button for 3 seconds. Release the button when Smart

config started is displayed on screen.

9. Press the Connect to WiFi button on your mobile device. The connection will be

completed within 10 ~ 60 seconds and the message MP Mini Delta is now

connected to Wi-Fi will be displayed on your device's screen and the IP address will

be displayed at the top of the printer's LCD screen.

Note that you may have difficulty connecting to the Wi-Fi network if you have a 2.4GHz

and 5GHz network with the same SSID. Try changing the SSID of the 5GHz network if this

occurs. For best results, move the printer to a location closer to the Wi-Fi router or access

point.

SOFTWARE INSTALLATION AND SETUP

As you've seen, you can print a model directly from a gcode file on a microSD™card and

this is the preferred method, as it does not require a continuous connection to your

computer. You can download gcode files to the microSD card and print them without

having to build any model files.

However, you can create your own gcode files using an open source program, such as Cura

or Repetier-Host, which are pre-installed on the microSD card that comes with the printer.

These programs use M200 models (typically .STL or .OBJ files) and, using machine specific

information, generate a gcode file with detailed instructions for the printer to create the

selected model. We recommend you start with Cura, since it includes a Slicing Engine.

Installing Cura for Windows

1. Use a card reader to read the contents on the

included microSD™card. Locate and double-

click the Cura_15.04.2.exe file to start the setup

program.

2. You may choose a new location for the

program files or accept the default

(recommended). Click Next to continue.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Monoprice Imprimante 3D

Monoprice

Monoprice 13860 Manuel utilisateur

Monoprice

Monoprice cadet Mode d’emploi

Monoprice

Monoprice MP10 Manuel utilisateur

Monoprice

Monoprice 30525 Manuel utilisateur

Monoprice

Monoprice 15710 Manuel utilisateur

Monoprice

Monoprice 35435 Manuel utilisateur

Monoprice

Monoprice MP Mini Delta V2 Manuel utilisateur

Monoprice

Monoprice MP CADET Manuel utilisateur

Monoprice

Monoprice Voxel 33820 Manuel utilisateur

Monoprice

Monoprice 21824 Manuel utilisateur

Monoprice

Monoprice maker architect 13861 Manuel utilisateur

Monoprice

Monoprice MP Mini SLA LCD Manuel utilisateur

Monoprice

Monoprice Select Mini Pro Manuel utilisateur

Monoprice

Monoprice extrusion i3 13860 Manuel utilisateur

Monoprice

Monoprice Delta Pro Manuel utilisateur

Monoprice

Monoprice 43363 Manuel utilisateur

Monoprice

Monoprice MP Mini Delta V2 Manuel utilisateur

Monoprice

Monoprice MP Education Guider II Manuel utilisateur

Monoprice

Monoprice 30526 Manuel utilisateur

Monoprice

Monoprice Select Mini 3D Printer V2 Manuel utilisateur

Monoprice

Monoprice 15365 Manuel utilisateur

Monoprice

Monoprice Maker Select Plus IIIP Manuel utilisateur

Monoprice

Monoprice MP Maker Pro Mk.1 Manuel utilisateur

Monoprice

Monoprice MP Mini Delta V2 Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur