Juniper WX 100 Manuel utilisateur
WX 100 QUICK START
1000 Mbps LC Fiber-Optic Connectors or
10/100/1000 BaseT Ethernet Interfaces
Welcome to the Juniper WX 100 application acceleration platform. This 2-rack unit network
infrastructure device has 1000 Mbps fiber-optic connectors or 10/100/1000 BaseT Ethernet
interfaces, and is deployed on the LAN side of the edge router. This quick start card describes
how to install the WX 100 in the data path between a switch and a router. To install the WX 100
“off-path” (connected only to the switch or router), refer to the WX/WXC Operator’s Guide.
Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, CA 94089
USA
1.888.314.JTAC
1.408.745.9500
www.juniper.net
Before you begin:
•Fiber-optic connectors do not support the “switch-to-wire” feature.
Therefore, it is strongly recommended that you install a WX 100 with fiber-
optic connectors in a high-availability (HA) environment.
•Inspect the package contents. Refer to the package contents document
enclosed with the product.
•Ensure sufficient AC power is available. Supply circuits should be protected
by a maximum 20A circuit breaker.
•Ensure a minimum of 6 inches clearance in the front and back of the chassis.
•Reserve sufficient rack space to connect client WX devices to the WX 100.
•Verify that all firewalls between WX devices allow traffic for TCP/UDP ports
3577 and 3578, and for IPComp, the IP payload compression protocol used
for reduction tunnels between devices (protocol number 108).
•Identify a fiber-optic LAN port or a 10/100/1000 BaseT Ethernet port that
transmits data to your WAN router. This port is typically from an aggregation
switch, or from another LAN device connected directly to the router.
•Obtain a license key. The license key determines the throughput levels for
the device, and properly registers the product. To obtain a permanent license
key, go to https://www.juniper.net/generate_license.
Installation:
➊Set up the chassis.
•For rack mount installation, install the supplied brackets, front panel
forward, to the sides of the device.
•For desktop installation, install the supplied rubber stands on the
bottom of the chassis.
NOTE: Do not connect the power cable until Step 4.
➋Connect the network cables.
For a WX 100 with LC fiber-optic connectors, you must obtain the appro-
priate conversion unit if the Switch (local device) or Router (remote
device) uses a different type of fiber-optic connector.
To connect the network cables:
•Locate the cable that connects from the switch (or other aggregating
device) to the router.
•Disconnect this cable from the router port and connect it to the
Local port on the WX 100.
•Connect a cross-over cable or a fiber-optics cable with an LC con-
nector (not provided) from the router port to the Remote port on the WX 100.
CAUTION: The WXC 590 and WX 100 require a cross-over cable to allow traffic to pass through during a reboot or system
failure (all other WX platforms use a straight-through cable). Always test connectivity with the power off (see the next step).
IMPORTANT: Fiber-Optic connectors do not support the “switch-to-wire” feature. Therefore, it is strongly recommended
that you install a WX 100 with fiber-optic connectors in a high-availability (HA) environment.
➌Verify bypass connectivity (not required for a fiber-optic WX 100)
Before applying power, verify that a WX 100 power failure will not block network traffic. One way of testing the bypass
connectivity is to Ping a host on the remote side of the WX 100 from a host on the local side of the WX 100.
NOTE: If you cannot verify bypass connectivity on both sides of the device, do not proceed to the next step.
Ensure that you are using the correct cables (crossover vs. straight-through), and verify that you have bypass
connectivity before applying power.
Power
WX 100
Adjustable rack
mounting ear
Adjustable rack
mounting ear
Power
WX 100
DB-9 console
port
Client ports
Remote port
Local port
WX 100 QUICK START
➍Connect the power.
Connect a power cable to each of the power supplies on the back of the
chassis, and connect the other end of the power cables to your local AC
power source. If one power supply stops functioning, the other power
supply can continue providing full power indefinitely. A failed power
supply can be removed and replaced while the device is running.
NOTE: The power usage is 300 Watts Max or 1025 BTU/hr. When you
want to disconnect power from the device, unplug BOTH power cables.
➎Configure the Network Settings.
Connect an ANSI compatible terminal to the console port, and use a terminal emulation program (e.g., HyperTerminal)
to log in to the CLI. Note the following serial port settings:
Baud Rate: 9600, Data Bits: 8, Parity: NONE, Stop Bits: 1,
Flow Control: NONE, Smooth-Scroll: DISABLED
•Start the terminal emulation program, and choose to connect via the serial port.
•At the User name and Password prompts, type admin for the user name and peribit for the password.
•Type an IP address, and press Enter. Next, type the subnet mask for the network, and press Enter. Finally, type the
IP address of the default gateway for this device, and press Enter.
•Type “save-config” and type “y” to confirm. You can safely bypass the other configuration questions at this time.
NOTE: By default, the interfaces are set to auto-negotiate. However, depending on the interface settings of the switch and
router (auto-negotiate or 1000/Full) it is recommended that you set the interface speed manually. The Local port setting
should match the interface settings of the switch, and the Remote port setting should match the interface settings of the
router. It is also recommended that the Local and Remote interface settings be the same.
➏Check the LEDs below the Local and Remote interfaces.
5•The BaseT Ethernet version has two rows of three LEDs:
•The Link/Activity LEDs indicate connectivity.
•The 100 and 1000 LEDs indicate the interface speed in Mbps.
•If the 100 and 1000 LEDs are off, the interface speed is 10 Mbps.
•If all 100 and 1000 LEDs are on, the device is in passthrough mode.
5•The fiber-optic version has one LED for each interface to indicate
1000 Mbps.
After checking the LEDs, verify connectivity across the device again
(as described in Step 3).
AC power
inputs
Remote port LEDs
Local port LEDs
Link/Activity
100
1000
Remote port
Local port
Passthrough
mode
WX 100 QUICK START
Quick Setup:
After powering on the device and assigning IP parameters, the next step is to log in to the Web console and run the Quick
Setup program. The first time you log in to the Web console, the Quick Setup program starts automatically and guides you
through initial configuration options for the device.
You can log in to the Web console from any workstation within your network. The Web console supports Microsoft Internet
Explorer version 6.0 (and later). Data is securely transmitted through HTTPS.
To log in to the Web console and run Quick Setup, follow these steps:
➊From a workstation within your network, start your Web browser and enter the following URL:
https://(ip address of the WX device)
5•Depending on your browser settings, the Security Alert dialog box may appear. Click Yes to proceed.
5•In the Enter Network Password dialog box, type admin for the user name and peribit for the password.
NOTE: This is a factory-configured password for the device. You will be asked to change the default password during the
Quick Setup.
➋Select an Operating Mode.
A device can run in Active mode or Profile Mode.
•Active Mode — Active operation where the device reduces data, accelerates TCP applications, and manages bandwidth.
• Profile Mode — Passive operation where the device can calculate potential data reduction statistics for all traffic,
individual applications, and specific remote subnets. The actual traffic is not affected.
CAUTION: Profile Mode disables the Remote interface. To use Profile Mode, the device’s Local interface must be connected
to a mirrored port on the switch, and the Remote interface must be disconnected. Traffic will be blocked if you select
Profile Mode when the device is installed in the data path.
For more information about Profile Mode, refer to the Operator’s Guide.
•Click Next to continue.
WX 100 QUICK START
➌Registration Server Setup.
One device must be designated as the Registration Server.
•To designate this device as the registration server, enter a registration server password in the appropriate fields.
The registration server password authenticates the devices in a community, and should be different from the
administrator password.
•If this device is not the registration server, enter the IP address and password of the current (or future) registration
server in the appropriate fields. This device will not process data until the registration server is configured.
•If you select the option to delay the formation of reduction tunnels, this device will not reduce or assemble data from
other devices until you enable reduction tunnel formation in the Endpoints page of the Web console.
•Click Next to continue.
➍Set the Time.
•If your network uses an NTP server for device time settings, enter the IP address of the NTP server. Otherwise, enter
the current time, date, and local time zone for the device. If applicable, select the Daylight Savings checkbox.
•Click Next to continue.
➎Specify Feature and Topology Settings.
The feature and topology settings ensure that device resources are used efficiently to reduce and assemble data.
• Select Active Flow Pipelining (AFP) or AFP and Application Flow Acceleration if you want to use these features.
• Choose the topology setting that best describes the device’s relationship to the other WX devices in the community (Hub,
Spoke, or Mesh). For a Hub or Mesh device, select the range of devices in the community.
• Click Next to continue.
WX 100 QUICK START
➏Advertise Local subnet.
By default, the device’s local subnet is not advertised to the other WX devices in the community. As a result, data destined for
this subnet is not reduced — even if there is a WX device in the path.
•If you want other WX devices to reduce data destined for this subnet, select the Advertise checkbox.
If you choose not to advertise the local subnet, you should review the Reduction Subnets page of the Web console
after completing the Quick Setup.
•In the Device name field, you can assign a name for the device.
•Click Next to continue.
❼Enter a license key.
By default, each device has a 30-day evaluation license. When the evaluation license expires, data will pass through the
device without reduction.
If you have purchased the device, you can use the serial number to obtain a permanent license key through the Online
License Service. The License Key server is accessible by clicking Online Service or by calling Support at 1-888-314-JTAC (or
408-745-9500).
•Enter the permanent license key in the License key field.
•Click Next to continue.
❽Change Administrator password.
•Enter a new Administrator password in the New password and Verify new password fields, and then click Finish.
NOTE: If you deselect the “automatic save” option, configuration settings will be reset by the next power cycle.
Where to go next:
The initial configuration is complete. To connect client WX devices to the WX 100 and configure all policy settings, refer to the
WX/WXC Operator’s Guide, which is located on the Documentation/Utilities CD. For additional product support information,
visit our Web site at http://www.juniper.net/support. If you need additional assistance, please contact Customer Care at
1-800-638-8296 (United States) or +1-408-936-1572 (outside the United States).
WX 100 QUICK START
530-016316-02
Table des matières
Autres manuels Juniper Matériel réseau
Juniper
Juniper JSA7800 Manuel utilisateur
Juniper
Juniper SRX320 Manuel
Juniper
Juniper EX4100-48P/T Manuel utilisateur
Juniper
Juniper CTP2000 Series Manuel utilisateur
Juniper
Juniper Junos Space JA1500 Manuel utilisateur
Juniper
Juniper SRX320 Manuel utilisateur
Juniper
Juniper Day One+ ACX7100-48L Manuel utilisateur
Juniper
Juniper NetScreen-IDP 3.0 Manuel utilisateur
Juniper
Juniper TCX1000 Manuel utilisateur
Juniper
Juniper T1600 Manuel utilisateur
Juniper
Juniper PTX10004 Instructions d'installation
Juniper
Juniper NSM4000 Instructions d'installation
Juniper
Juniper CTP1000 Series Instructions d'installation
Juniper
Juniper NFX250-S1 Manuel utilisateur
Juniper
Juniper JSA7800 Manuel utilisateur
Juniper
Juniper MX480 Instructions d'installation
Juniper
Juniper 16-PORT GIGABIT ETHERNET XPIMS Manuel utilisateur
Juniper
Juniper MX240 Manuel utilisateur
Juniper
Juniper STRM 5000 Manuel
Juniper
Juniper XRE200 - Instructions d'installation
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
