Juniper SSR1400 Manuel utilisateur
Quick Start Guide
SSR1400
IN THIS GUIDE
Step 1: Begin | 1
Step 2: Up and Running | 5
Step 3: Keep Going | 15
Step 1: Begin
SUMMARY
In this guide, we provide a simple, three-step path, to quickly
get the Juniper Networks® SSR1400 appliance up and
running on Juniper Mist™ cloud. You'll learn how to install,
power on, and congure basic sengs for an AC-powered
SSR1400 appliance.
IN THIS SECTION
Meet the SSR1400 | 1
Install the SSR1400 | 2
Power On | 4
Meet the SSR1400
The SSR1400 is a 1 U xed conguraon appliance that's ideal for medium data center or campus deployments.
Powered by the Juniper® Session Smart Router (SSR) soware, the SSR1400 provides secure and resilient WAN
connecvity.
The SSR1400 has four 1 GbE ports, four 1/10/25 GbE SFP28 ports, four 10 GbE SFP+ ports, a management port (for
Mist operaons), 256 GB of memory, and a 512 GB enterprise-grade solid-state drive (SSD) for storage.
Install the SSR1400
IN THIS SECTION
What's in the Box? | 2
What Else Do I Need? | 2
Rack It | 3
What's in the Box?
Along with your SSR1400, you’ll nd:
• RJ-45 to USB A serial cable
• AC power cord (country-specic)
• Rack mount kit
• Two front mounng brackets
• Two side mounng rails
• Two rear mounng blades
• Six M4 at-head screws (for the front mounng brackets)
• Ten rack screws and cage nuts
• Two M3 at-head screws
What Else Do I Need?
• Number 2 or 3 Phillips (+) screwdriver, depending on the size of your rack screws
• A management host such as a laptop or desktop PC
2
• A grounding cable
CAUTION: Ensure that a licensed electrician has aached the appropriate grounding lug to your
grounding cable. Using a grounding cable with an incorrectly aached lug can damage the SSR1400.
Rack It
Here’s how to install the SSR1400 in a four-post rack:
1. Review the General Safety Guidelines and Warnings.
2. Wrap and fasten one end of the electrostac discharge (ESD) cable grounding strap around your bare wrist, and
connect the other end to a site ESD point.
3. Aach the front mounng brackets to the front of the chassis using the six M4 at-head screws.
4. Aach the side mounng rails to the chassis by aligning the keyholes on the mounng rails over the shoulder
screws on the chassis and then sliding the mounng rails into place. Use the two M3 at-head screws to secure the
rails.
5. Grasp both sides of the SSR1400 chassis, li it, and posion it in the rack so that the front mounng bracket holes
align with the threaded holes in the rack rail.
NOTE: Ensure that the rear of the appliance is supported while you mount the SSR1400 in the rack.
6. While you’re holding the SSR1400 in place, have a second person insert and ghten the rack-mount screws to
secure the front mounng brackets to the rack rails. Tighten the screws in the two boom holes rst, then ghten
the screws in the two top holes next.
3
7. Connue to support the SSR1400 in place and have the second person slide the rear mounng blades into the
channels of the side mounng rails.
8. Secure the rear mounng blades on each side of the chassis to the rack post using rack mounng screws.
9. Check that the front mounng brackets on each side of the rack are lined up with each other.
10. Aach a grounding cable to earth ground and then aach the other end to the SSR1400 grounding point.
11. Dress the grounding cable. Ensure that it doesn’t touch or block access to other device components, and that it
doesn’t drape where people could trip over it.
Power On
Now that you’ve installed your SSR1400 in the rack and grounded the chassis, you’re ready to connect it to power.
4
NOTE: If you want to connect your SSR1400 to the Mist Cloud, you must connect the Ethernet/transceiver
cable to your preferred management port (MGMT or other) before powering on the appliance. The Ethernet/
transceiver cable must provide connecvity to the internet or to your Mist Cloud instance.
The SSR1400 supports redundant AC power supplies that are pre-installed at the factory. It comes with two AC power
supplies preinstalled on the rear of the device.
1. Wrap and fasten one end of the ESD grounding strap around your bare wrist, and connect the other end to one of
the ESD grounding points on the router.
2. Turn o the power switch on the SSR1400.
3. Make sure that the power supplies are fully inserted in the chassis.
4. Pull the power cord retainer down and plug each power cord into the power supply socket.
5. Push the power cord retainer onto the power cord.
6. If the AC power source outlet has a power switch, turn it o.
7. Plug in each power cord to an AC power source outlet.
WARNING: Ensure that the power cord does not block access to the appliance components or drape
where people can trip on it.
8. If the AC power source outlet has a power switch, turn it on.
9. Turn on the power switch on the SSR1400.
Step 2: Up and Running
IN THIS SECTION
Connect Your SSR1400 to the Mist Cloud | 6
Claim Your Appliance | 7
5
Add the Network | 9
Add Applicaons | 9
Create a Template | 10
Assign the Template to a Site | 14
Assign the SSR1400 to a Site | 14
Now that the SSR1400 is powered on, let's get it up and running on Juniper Mist™ cloud. You'll need Juniper Mist WAN
Assurance subscripon and login credenals for the Juniper Mist portal.
Connect Your SSR1400 to the Mist Cloud
Your SSR1400 uses port MGMT (mgmt-0/0/0) as the default port to contact Mist for zero-touch provisioning (ZTP). It
uses port 0/3 (xe-0/0/3) to connect to the LAN.
1. Connect the MGMT port to an Ethernet link that can assign a DHCP address to the SSR1400 and provide
connecvity to the Internet and Mist.
NOTE: For management, you can connect the SSR1300 to Mist using the MGMT port. You can also connect
to Mist from one of the WAN ports only when the MGMT port is disconnected, or does not have a valid
DHCP leased address and default route.
Do not change the Mist management port once your appliance is powered on and connected to the Mist
Cloud instance.
2. Connect port 3 to your LAN devices, such as
• Mist-managed Juniper EX switches
• Mist APs
• User devices
6
3. Power on the SSR1400.
Your SSR1400 is now connected to the Mist cloud.
Claim Your Appliance
IN THIS SECTION
Mist AI App QR Scan | 8
Enter the Mist Claim Code | 8
To add the SSR1400 to your organizaon's WAN Edge inventory, you'll need to enter the SSR1400 claim informaon
into Mist. The claim label (QR code scker) on the front panel has the claim informaon.
To enter the claim informaon, do one of the following:
• Scan the QR code with the Mist mobile applicaon.
• You can also manually enter the claim code in Mist. The claim code is the number above the QR code. For example:
In this picture, the claim code is KF9HC588GPSFRCZ.
7
Mist AI App QR Scan
You can download the Mist AI App from the Mac App Store or from Google Play Store.
1. Open the Mist AI app.
2. Click Claim Devices to Org.
3. Scan the QR code.
Enter the Mist Claim Code
1. Log in to your organizaon on the Juniper Mist cloud.
2. Select Organizaon > Inventory from the menu on the le, then select the WAN Edges tab at the top.
3. Click Claim WAN Edges in the upper right poron of the inventory screen.
4. Enter the SSR1400 claim code and click Add.
5. Uncheck the Assign claimed WAN Edges to site check box to place the SSR1400 in the inventory. The SSR1400 is
assigned to a site later.
6. Click the Claim buon to claim the SSR1400 into your inventory.
Video: Add the Claim Informaon in Mist
8
Add the Network
Add the network to be used for accessing applicaons over a LAN network segment.
1. Select Organizaon > Networks from the menu on the le.
2. Click Add Networks in the upper-right corner of the Networks page.
Video: Access the Add Networks Page
3. Enter a name for the network.
4. Enter the network subnet as 192.168.1.0/24.
5. Click Add.
This network is now dened for use across the enre organizaon, including the template that you'll apply to your
SSR1400.
Add Applicaons
1. Select Organizaon > Applicaons from the menu on the le.
2. Click Add Applicaons in the upper-right corner of the Applicaons page.
Video: Access the Add Applicaons Page
3. Enter the name for the applicaon as Internet.
9
4. Enter 0.0.0.0/0, or all IPv4 address spaces in the IP Addresses eld.
5. Click Add.
Your organizaon is now set up to provide access to the Internet.
Create a Template
Excellent! Now you have the SSR1400 waing to be claimed, a network for your LAN, and an Internet applicaon. Next,
you need to create a WAN Edge template that es them all together. Templates are reusable and keep the conguraon
consistent for every SSR1400 you deploy.
1. Select Organizaon > WAN Edge Templates from the menu on the le.
2. Click Create Template in the upper-right corner of the WAN Edge Templates page.
3. Enter a name for the template.
4. Click Create.
5. Enter the NTP and DNS informaon for the WAN edge device.
Video: Create the Template
Congure the WAN Port
The rst thing to do in your template is to dene which port to use for the WAN.
1. Scroll to the WAN secon of the template, and click Add WAN.
2. Enter the name for the WAN port as wan1.
10
Autres manuels pour SSR1400
2
Table des matières
Autres manuels Juniper Matériel réseau
Juniper
Juniper TCX1000 Manuel utilisateur
Juniper
Juniper QFX10016 Manuel utilisateur
Juniper
Juniper CTP2000 Series Instructions d'installation
Juniper
Juniper ACX7100 Manuel utilisateur
Juniper
Juniper SSR130 Manuel utilisateur
Juniper
Juniper MX480 Instructions d'installation
Juniper
Juniper NFX150 Instructions d'installation
Juniper
Juniper SSR1400 Manuel utilisateur
Juniper
Juniper Day One+ QFX5700 Manuel utilisateur
Juniper
Juniper WX 15 Manuel utilisateur
Juniper
Juniper SRX300 Series Manuel utilisateur
Juniper
Juniper SSR120 Instructions d'installation
Juniper
Juniper SRX300 Series Instructions d'installation
Juniper
Juniper QFX Series Manuel utilisateur
Juniper
Juniper SRX300 Series Manuel utilisateur
Juniper
Juniper NetScreen-IDP 3.0 Manuel utilisateur
Juniper
Juniper EX9200 Series Manuel utilisateur
Juniper
Juniper SRX5400 Manuel de service
Juniper
Juniper MX150 Manuel utilisateur
Juniper
Juniper CSE2000 Manuel
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
