HP D7171A - NetServer - LPr Manuel utilisateur

HP NetServer

Ultra3 SCSI Hot-Swap

Hard Disk Drive and Tray

User Guide

HP Part Number 5969-5922

Printed in February 2000

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard shall not

be liable for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced, or

translated to another language without the prior written consent of Hewlett-

Packard Company.

Hewlett-Packard Company

Network Server Division

Technical Communications/MS 45SLE

10955 Tantau Avenue

Cupertino, CA 95014-8059 USA

Audience Assumptions

The guide is for the person who installs, administers, and troubleshoots LAN

servers. Hewlett-Packard Company assumes you are qualified in the servicing of

computer equipment and trained in recognizing hazards in products with

hazardous energy levels.

iii

Contents

1 Introduction to Ultra3 Drives..........................................................................1

Overview............................................................................................................1

Ultra3 Drives are Low Voltage Devices.........................................................1

Ultra3 Drives Have Two Heights; Drive Cages Have Several Sizes.............1

Filler Panels...................................................................................................1

Disk Spacers .................................................................................................2

Verify Contents .................................................................................................. 2

2 Installation Procedure..................................................................................... 3

Installing the Ultra3 Disk Drive Module..............................................................3

Removing the Ultra3 Disk Drive Module............................................................8

Installing the Ultra3 Drive in a Tray (optional)....................................................9

3 Supported Configurations............................................................................11

4 Warranty and Support...................................................................................13

Hardware Warranty..........................................................................................13

HP Repair and Telephone Support..................................................................13

HP World Wide Web Site................................................................................13

5 Regulatory Information................................................................................. 15

Index.................................................................................................................... 17

1 Introduction to Ultra3 Drives

Overview

Ultra3 SCSI hot-swap hard disk drives provide higher I/O bandwidth and can

work with longer cable lengths than Ultra drives. Ultra3 drives operate at SCSI

bus data rates of up to 160 MB per second--double the rate of Ultra2 SCSI. With

Ultra3 drives, HP NetRAID environments and applications will show immediate

increases in performance.

Note: These drives are also backward compatible with Ultra2

controller systems.

Ultra3 Drives are Low Voltage Devices

Ultra3 drives have LVD (low voltage differential) signal levels. The low voltage

requirements allow the integration of the differential drivers and receivers into

drive SCSI controllers. LVD provides the signal quality necessary to run at Ultra3

data rates. LVD also allows for significantly longer SCSI bus cable lengths.

Ultra3 Drives Have Two Heights; Drive Cages Have Several Sizes

Ultra3 disk drive modules come in two heights: the 1-inch (2.5 cm) low profile

drive and the 1.6-inch (4 cm) half-height drive. NetServer drive cages come in

several sizes. There are two types of six-drive cages. The LH3, LH4, and RS-12

cages support a mix-and-match of 1-inch low profile drives and 1.6-inch (4 cm)

half-height drives. Other NetServers with six-drive cages support either 1-inch (2.5

cm) low profile drives or 1.6-inch (4 cm) half-height drives. Refer to your

NetServer manuals for details. Chapter 3 lists the places where the supported

configurations can be found.

Filler Panels

When you have fewer drives than the hot-swap cage supports, filler panels must be

inserted in empty disk locations. Filler panels ensure that the hot-swap cage has

the proper ventilation and air flow. You will remove the filler panel when you

insert a new Ultra3 disk drive module. (Figure 2-1 in the next chapter shows a

filler panel.)

Chapter 1 Introduction to Ultra3 Drives

Disk Spacers

When your hot-swap cage holds a mix of low profile and half-height drives, one

drive may require a disk spacer. The disk spacer fills empty space between one

drive and the adjacent drive. Disk spacers can be mounted on 1-inch (2.5 cm) low

profile drives or 1.6-inch (4 cm) half-height drives. (Figure 2-2 in the next chapter

shows a disk spacer.)

Verify Contents

The Ultra3 SCSI Hot-swap Hard Disk Drive and Tray Accessory Kit contains the

following items:

•Ultra3 SCSI hot-swap hard disk drive module

•disk spacer

•Ultra3 SCSI Hot-swap Hard Disk Drive and Tray User Guide

If anything is missing or damaged, call your reseller.

2 Installation Procedure

This chapter describes how to install the Ultra3 disk drive module in your

HP NetServer, and provides instructions for removing and storing the disk drive

module. Additionally, this chapter describes how to attach an Ultra3 drive to a hot-

swap tray.

Installing the Ultra3 Disk Drive Module

CAUTION Protect the Ultra3 disk drive module from static electricity by

leaving it in its antistatic bag until you are ready to install it.

Before handling the disk drive module, touch any unpainted

metal surface to discharge static electricity. When you remove

the disk drive module from the antistatic bag, handle it only by

the frame.

Do not touch the electrical components. Place the disk drive

module on the antistatic bag whenever you set it down.

Disk drive modules are very susceptible to mechanical shock

and can be damaged by a drop as short as one-quarter of an

inch (.5 cm). Take care when unpacking and handling the disk

drive module. If the drop would crack an egg, it will damage

the drive.

Chapter 2 Installation Procedure

1. If there is a filler panel in the drive location, remove the filler panel as

follows:

• Press the latch and insert your fingers.

• Using your fingers, pull the filler panel straight out.

Figure 2-1 shows a filler panel being removed from a system with a

six-drive hot-swap cage. Your HP NetServer’s enclosure may have a

four-drive cage or a two-drive cage.

Figure 2-1. Removing the Filler Panel

Chapter 2 Installation Procedure

2. Disk spacers attach to the disk drive module with four small feet.

To remove a disk spacer from the adjacent disk drive module:

• Slide the disk spacer back, a fraction of an inch (2.5 cm), away from

your body.

• Tilt up the front of the disk spacer to disengage the front two feet.

• Pull the disk spacer forward slightly, to disengage the back two feet and

lift.

Figure 2-2. Removing the Disk Spacer From a Disk Drive Module

To attach a disk spacer to a disk drive module:

• Tilt up the front of the disk spacer and engage the back two feet.

• Press the disk spacer back, a fraction of an inch (2.5 cm), away from

your body.

• Lower the front of the disk spacer into place to engage the front two

feet.

Chapter 2 Installation Procedure

3. On the Ultra3 disk drive module, press the blue latch in and pull the lever

out as far as it can go as shown in Figure 2-3. Pulling open the lever

retracts the locking tab on the side of the disk drive module. Be careful not

to use extreme force when pulling the lever.

Figure 2-3. Pulling Open the Lever Retracts the Locking Tab

on the Side of the Drive

4. Slide the Ultra3 disk drive module slowly into the drive location until it

stops. In some systems, drives are inserted horizontally (Figure 2-4); and in

other systems, drives are inserted vertically (Figure 2-5).

Be careful of the light pipes as you insert the drive. The light pipes are

fragile.

CAUTION You must insert the drive slowly and gently. The connector is

designed with some long pins that must make contact before

the short pins. If the disk drive module is inserted too quickly,

the short pins make contact too quickly after the long pins.

The in-rush current can cause the power supply to shut down.

5. Press the lever in, until you hear the latch click into place.

Autres manuels pour D7171A - NetServer - LPr

117

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Matériel informatique

HP Model 744 - VME Workstation Manuel utilisateur

HP AF079A Guide d'installation

HP Compaq t5500 Manuel utilisateur

HP 6-Port SATA RAID Manuel utilisateur

HP 64782 Manuel utilisateur

HP QMH2572 8Gb FC HBA Instructions d'utilisation

HP JG560A Manuel utilisateur

HP JG587A Manuel utilisateur

HP M8201R Manuel utilisateur

HP GbE2c - Blc Layer 2/3 Fiber SFP Option Comment utiliser

HP HP-UX 10.20 Manuel utilisateur

HP 64751 Manuel utilisateur

HP NC550SFP Manuel utilisateur

HP SC08Ge Manuel utilisateur

HP 273914-B21 - Smart Array 6404/256 RAID... Manuel utilisateur

HP A3550A - High Availability Disk Arrays Model 20 Storage... Manuel utilisateur

HP HPE LSWM2XGT2PM Manuel utilisateur

HP E8402A Guide de dépannage

HP 705 Guide de démarrage rapide

HP 3000 III Series Manuel utilisateur

HP 98625A Manuel utilisateur

HP D7171A - NetServer - LPr Manuel d'installation et d'exploitation

HP Xw4600 - Workstation - 2 GB RAM Manuel utilisateur

HP A4800A Mode d’emploi

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur