HP Integrity rx1600 Manuel utilisateur

February 2004

Printed in the U.S.A.

Smart Array (A9890A) Cable Routing

The purpose of this document is to provide cable routing information when a Smart Array PCI-X RAID card (A9890A)

is used to drive the embedded hard disk drives. The existing SCSI cable connected to the Channel A connector on the

system board is relocated to the Channel A connector on the Smart Array PCI-X card installed in slot 1 (full-length slot)

of the PCI cage.

The SCSI cable is routed from the PCI cage under the power supply bracket and over the IDE cable, if installed, avoiding

blocking the airflow of the chassis fans.

Refer to the hp integrity rx1600 Operation and Maintenance Guide for detailed instructions on powering down the

server, extending the server from a rack, and removing and replacing covers and components.

1. Disconnect the SCSI cable from the Channel A connector on the system board by pulling on the cable release strap.

See figure 1.

Figure 1. SCSI Channel A Connector on System Board

2. Remove the PCI cage from the server.

3. Remove any accessory card installed in PCI slot 2 (half-length slot).

4. Install the Smart Array PCI-X RAID card (A9890A) in PCI slot 1 (full-length slot).

5. Orient the PCI cage with the installed PCI-X RAID card component-side-up allowing routing of the SCSI cable.

See figure 2.

Figure 2. Cable Routing on Smart Array Card and PCI Cage

NOTE If an optional management processor card is installed in the server, follow the

instructions provided in the hp integrity rx1600 Operation and Maintenance Guide to

remove the card, allowing access to the Channel A connector. Reinstall the card after the

SCSI cable has been disconnected.

Channel A

connector

Around heatsink

Exit parallel to

connector

Channel A1

Under slot 2 connector

6. Attach the SCSI Channel A connector (previously removed from the system board connector) to the A1 Channel of

the PCI-X RAID card.

7. Route the SCSI cable around the heatsink on the PCI-X RAID card and under the edge of the PCI slot 2 connector.

See figure 2.

8. Continue routing the cable parallel to the connector edge of the PCI cage.

9. Reinstall any accessory card previously removed from PCI slot 2.

10. Install the PCI cage into the server chassis.

11. Route the SCSI cable under the power supply bracket as shown in figure 3.

Figure 3. Route Cable under Power Supply Bracket

12. Route the SCSI cable through the access slot of the fan assembly to the connector on the SCSI backplane.

See figure 4.

Figure 4. Cable Routing at SCSI Cage

13. Complete the installation by following the instructions provided in the hp integrity rx1600 Operation and

Maintenance Guide for closing up the server, installing in a rack, and powering-up. To enable RAID refer to the

A9890A documentation.

NOTE The SCSI cable should be routed over the IDE cable if the IDE cable is present.

CAUTION Do not block the airflow of the chassis fans. Reduced airflow may cause overheating.

Power Supply

Bracket

Route over IDE

cable (if present)

Do not block fans

Autres manuels pour Integrity rx1600

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Matériel informatique

HP ML570 - ProLiant - G2 Manuel utilisateur

HP Xw6600 - Workstation - 2 GB RAM Manuel utilisateur

HP E2465A PowerPC 604 PGA Manuel utilisateur

HP 5998-1600 Manuel utilisateur

HP StorageWorks FC1142SR Manuel utilisateur

HP Pavilion xl700 - Desktop PC Manuel utilisateur

HP Metal Jet S100 Manuel utilisateur

HP Xw8400 - Workstation - 4 GB RAM Manuel utilisateur

HP E8402A Guide de dépannage

HP Integrity rx8620 Manuel utilisateur

HP QMH2672 Manuel utilisateur

HP Sangoma 2 Instructions d'installation

HP 64793 Series Manuel utilisateur

HP 64782 Manuel utilisateur

HP CB001A Manuel utilisateur

HP Xw4600 - Workstation - 2 GB RAM Feuille d'instructions

HP Smart Array P400 Instructions d'utilisation

HP Kayak XW U3-W3 Manuel utilisateur

HP E5000 Manuel utilisateur

HP UNDP-1H Manuel utilisateur

HP A4800A Mode d’emploi

HP Adaptec ultra p2280a Manuel utilisateur

HP P Class 450/500/550/600/650/700/750 Manuel

HP A3550A - High Availability Disk Arrays Model 20 Storage... Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur