H3C SecPath PSR300-12A2 Manuel utilisateur

H3C SecPath PSR300-12A2 &

PSR300-12D2 Power Modules

User Manual

New H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6W102-20200303

No part of this manual may be reproduced or transmitted in any form or by any means without prior written

consent of New H3C Technologies Co., Ltd.

Trademarks

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this

document are the property of their respective owners.

Notice

The information in this document is subject to change without notice. All contents in this document, including

statements, information, and recommendations, are believed to be accurate, but they are presented without

warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions

contained herein.

Preface

Audience

This documentation is intended for:

•Network planners.

•Field technical support and servicing engineers.

•Network administrators working with the the H3C SecPath PSR300-12A2 & PSR300-12D2.

Documentation feedback

You can e-mail your comments about product documentation to info@h3c.com.

We appreciate your comments.

Contents

Overview························································································1

Views······································································································································1

Technical specifications···············································································································2

LEDs·······································································································································2

Installing and removing the power supply ··············································3

Safety precautions ·····················································································································3

Tools·······································································································································3

Installing and removing the power supply························································································3

Installing the power supply ····································································································3

Connecting the power cord····································································································4

Removing the power supply···································································································5

Overview

The PSR300-12A2 is an AC-input and DC-output power supply. The PSR300-12D2 is a DC-input

and DC-output power supply. They provide a maximum output power of 300 W.

The PSR300-12A2 and PSR300-12D2 power supplies have the following features:

•Provide protection against input overcurrent, input undervoltage, output overvoltage, output

short-circuit, and overtemperature.

•Support for 1+1 redundancy and load sharing.

•Hot swappable. You can hot swap a power supply when another power supply is operating.

Views

Figure 1 PSR300-12A2

(1) Power switch ("O" represents off and "—" represents on)

(2) Power receptacle (3) Air vent

(4) Handle (5) Power output status LED

(6) Power input status LED (7) Securing holes for the power cord retaining clasp

(8) Fastening screw

Figure 2 PSR300-12D2

(1) Power switch ("O" represents off and "—" represents on)

(2) Power receptacle (3) Air vent

(4) Handle (5) Power output status LED

(6) Power input status LED (7) Screw holes for securing the power cord connector

(8) Fastening screw

Technical specifications

Table 1 Technical specifications

Item Specifications

Rated input voltage •PSR300-12A2: 100 VAC to 240 VAC

•PSR300-12D2: –48 VDC to –60 VDC

Output voltage 12 V

Maximum output current 25 A

Maximum output power 300 W

Dimensions (H × W × D) 40.13 × 101.6 × 234.9 mm (1.58 × 4.00 × 9.25 in)

Operating temperature 0°C to 55°C (32°F to 131°F)

Operating humidity 5% RH to 95% RH, noncondensing

LEDs

The power supply uses power input and power output LEDs to indicate the power input and output

status, respectively.

Table 2 LED description

LED Status Description

Power input status LED (AC OK or Input) Off No power is being input or an input failure has

occurred.

On Normal power input.

Power output status LED (DC OK or

Output) Off No power is being output or an output failure has

occurred.

On Normal power output.

If the power input LED is on but the output LED is off, an output issue or an overtemperature

condition might have occurred. To resolve the issue:

1. Turn off the power switch and disconnect the power cord. Then reconnect the power cord and

turn on the power switch.

This operation resolves the power supply failure caused by an output overvoltage, output

short-circuit, or output overcurrent condition. The power supply shuts down and latches off if

one of these conditions occurs and cannot automatically restore operation.

2. If the issue persists, the temperature might be high. Take measures to decrease the

temperature to an acceptable range. The power supply will automatically restore operation.

Installing and removing the power supply

Safety precautions

To avoid possible bodily injury and power supply and device damage, follow these safety

precautions:

•When installing and removing the power supply, always wear an ESD wrist strap and makesure

it makes good skin contact.

•Make sure the voltage of the power source is as required by the power supply, and the output

voltage of the power supply is as required by the device.

•To avoid bodily injury, do not touch any bare wire or terminal.

•Do not place the power supply in a wet location, and prevent liquid from flowing into the power

supply.

•To avoid power supply damage, do not open the power supply. If the internal wires or units are

faulty, contact H3C Support.

Tools

When installing and removing a power supply and power cord, you must wear an ESD wrist strap.

Prepare it yourself.

Installing and removing the power supply

The installation and removal procedures are similar for the PSR300-12A2 and PSR300-12D2 power

supplies. The following procedures install and remove a PSR300-12D2 power supply.

Installing the power supply

CAUTION:

To avoid bodily injury and device damage, strictly follow the procedure in Figure 3 to install the

power supply.

Figure 3 Power supply installation procedure

Install the power supply

Connect the power cord

Turn on the circuit breaker

Start

End

To install the power supply:

1. Wear an ESD wrist strap and make sure the strap makes good skin contact and is reliably

grounded.

2. Unpack the power supply and make sure the power supply model is as required.

Keep the power supply package secure for future use.

3. As shown in Figure 4, correctly orient the power supply (with the lettering on it upwards).

Grasping the module handle with one hand and supporting the module bottom with the other,

push the module slowly into the slot along the guide rails. Make sure the power supply has good

contact with the backplane connectors.

The power supply and power supply slot are designed to prevent disorientation and

misalignment. If you cannot insert the power supply smoothly into the slot, the orientation might

be wrong or the power supply is not aligned correctly with the slot. Pull out the power supply,

reorient the power supply or realign it with the slot, and insert it again.

4. When the power supply is fully seated in the slot, fasten the screw on the power supply.

Figure 4 Installing the power supply

Connecting the power cord

Connecting the AC power cord

WARNING!

•Make sure each power cord has a separate circuit breaker.

•Before connecting a power cord, turn off the circuit breaker for it.

To connect the AC power cord:

1. As shown in Figure 5, pivot up the power cord retaining clip, insert the female connector of the

AC power cord into the AC-input power receptacle on the power supply, and then pivot down

the power cord retaining clip.

Figure 5 Connecting the AC power cord to the power supply

2. Connect the other end of the AC power cord into an AC power source, and turn on the circuit

breaker for the power cord.

3. Turn on the power switch. If the AC OK LED is on, the power cord is connected correctly. If the

AC OK LED is off, the connection might be wrong. Verify the installation and resolve the issue.

Connecting the DC power cord

1. As shown in Figure 6, insert the connector of the DC power cord into the DC-input receptacle on

the power supply. Then fasten the screws on the connector.

The connector of the DC power cord and the DC-input receptacle are designed to prevent

disorientation. If you cannot insert the connector smoothly into the receptacle, the orientation

might be wrong. Remove the connector, reorient it, and connect it again.

2. Use a releasable cable tie to secure the power cord to the handle of the power supply.

Figure 6 Connecting the DC power cord

3. Connect the other end of the DC power cord to a DC power source.

4. Turn on the power switch on the power supply. If the Input LED is on, the power cord is

connected correctly. If the Input LED is off, the connection might be wrong. Verify the

installation and resolve the issue.

Removing the power supply

CAUTION:

To avoid bodily injury and device damage, strictly follow the procedure in Figure 7 to remove the

power supply.

Figure 7 Power supply removal procedure

To remove the power supply:

1. Turn off the circuit breaker for the power cord.

2. Wear an ESD wrist strap and make sure the strap makes good skin contact and is reliably

grounded.

3. Turn off the power switch.

4. Loosen the releasable cable tie that secures the power cord to the handle of the power supply.

5. Loosen the screws on the power cord connector and then remove the power cord.

Figure 8 Removing a DC power cord connector

(1) Loosen the screws on the power cord connector

(2) Pull the connector out

6. As shown in Figure 9, loosen the screwon the power supply. Grasping the powersupply handle

with one hand, pull the power supply part way out of the slot. Supporting the power supply

bottom with the other, pull the power supply slowly out of the slot along the guide rails.

Autres manuels pour SecPath PSR300-12A2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels H3C Unité de contrôle

H3C

H3C PSR250-12A Manuel utilisateur

H3C

H3C PSR750-A Manuel utilisateur

H3C

H3C S9500E Series Manuel de la liste des pièces

H3C

H3C PSR450-12A Manuel utilisateur

H3C

H3C SecPath NSQM2AC1400 Manuel utilisateur

H3C

H3C LSXM1SEERBXD2 Manuel utilisateur

H3C

H3C SecPath PSR300-12A2 Manuel utilisateur

H3C

H3C S9500E LSR1FW2A1 Manuel utilisateur

H3C

H3C LSBM1WCM2A0 Manuel utilisateur

H3C

H3C SecPath DC2400 Manuel utilisateur

H3C

H3C LSVM1S9810FAN Manuel utilisateur

H3C

H3C PSR6000 Manuel utilisateur

H3C

H3C SecPath AC2500 Manuel utilisateur

H3C

H3C SFP-GE-SX-MM850-A Manuel utilisateur

H3C

H3C PSR2400-54A Manuel utilisateur

H3C

H3C SecPath NSQ1FAB08D0 Manuel utilisateur

H3C

H3C SR6600 SPE-FWM Manuel utilisateur

H3C

H3C LSQ1LBSC0 Manuel utilisateur

H3C

H3C PSR180-56A Manuel utilisateur

H3C

H3C SecBlade Manuel utilisateur

H3C

H3C PSR300-12A Series Manuel utilisateur

H3C

H3C SecPath NSQ1FAB04B0 Manuel utilisateur

H3C

H3C PSR2400-12AHAH-B Manuel utilisateur

H3C

H3C SecPath M9000 NSQM1CGQ20 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur