Flashforge Adventurer 4 Pro Manuel utilisateur
用户使用手册
Adventurer 4 Pro / 冒险家4 Pro
User Guide
EN/CN-A04
中文P32
本手册仅适用于闪铸科技 冒险家4 Pro 3D打印机
This guide is only applicable to FLASHFORGE Adventurer 4 Pro 3D printer.
Scan the QR code to view the unboxing
video, which is also accessible on the
USB flash drive.
扫码观看开箱视频
或打开U盘观看
CONTENTS
Notice
Parameters
Chapter 1 Adventurer 4 Pro
1.1 - Component Introduction
1.2 - Packing List
Chapter 2 Unpacking
Chapter 3 Software Installation
Chapter 4 Equipment Preparation
Chapter 5 First Printing
Chapter 6 User Interface Introduction
Chapter 7 Q&A
Chapter 8 Help and Support
06
07
02
05
06
08
09
10
14
17
25
31
17
19
19
20
21
22
22
22
23
24
24
01
6.1 - Build
6.2 - Prepare
6.2.1 - Preheat
6.2.2 - Filament
6.3 - Settings
6.4 - Maintain
6.4.1 - Upgrade
6.4.2 - Log
6.4.3 - Calibration
6.4.4 - Change Extruder
6.4.5 - Maintain
Notice
Safety Notice: please read and strictly follow all the
safety warnings and notice below.
Work Environment Safety
Keep your work place tidy.
Do not operate the device in the presence of flammable liquids, gases or dust.
The high temperature generated by equipment operation may react with
combustible gases, liquids, and airborne dust, thus causing fire.
Keep the device out of children's and untrained people's reach.
Electrical Safety
02
Note: Every printer has been tested before leaving the factory. If there are some filament
residues in the extruder or some tiny scratches on the build plate, it is normal and
won’t affect the printing quality.
Always use the device with a properly grounded outlet. Do not refit the device's plug.
Ungrounded / improperly grounded / refitted plugs will increase the risk of leakage
of electricity.
Do not expose the device to damp or hot-sun environment. Humidity will increase the
risk of electric leakage. Exposure to sunlight will accelerate the aging of plastic parts.
In case of device damage, please use the power cord provided by Flashforge.
Avoid using the device during a thunderstorm.
In case of uncertain accidents, please unplug the device if you do not use it for long.
When grounding, plug the power cord into the three-in-one socket and connect to the
external grounding wire through the grounding terminal of the three-in-one socket.
Check and replace the fuse: To prevent electric shock, please be sure to turn off the
power switch and unplug the power cord before checking or replacing the fuse.
Replace the fuse: Open the fuse box of the three-in-one socket and replace the fuse
with the fuse of 5*20, T10AL250V specification.
03
Environment Requirements
Placement Requirements
The device must be placed in a dry and ventilated environment. The distance of
the left, right and back side space should be at least 20cm, and the distance of the
front side space should be at least 35cm. Device storage temperature: RT 0-40℃.
Temperature: RT 15-30℃; moisture: 20%-70%.
Cautions
Keep the inside of the device clean and tidy. Do not place metal objects into the
chute at the bottom of the platform.
Please clean up the filament debris in time. It is recommended to operate this
outside the equipment.
Any modifications to the device will invalidate the guarantee.
Lower the build plate before loading/unloading filament. The distance between
the nozzle and build plate should be kept for at least 50mm.
Operate the device in a well-ventilated environment.
Never use the device for illegal activities.
Never use the device to make any food containers.
Never put the prints into your mouth.
Personal Safety
Do not touch the nozzle and build plate during printing.
Do not touch the nozzle and plate after printing to avoid high-temperature scalds
or mechanical damage!
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and
gloves away from moving parts.
Do not operate the device while you are tired or under the influence of drugs,
alcohol or medication.
Hot surface
Do not touch
Warning crushing
of hands
Keep this area
clear
Keep body parts away
from moving parts
04
Legal Notice
All the information in this document is subject to any amendment or change
without the official authorization from Flashforge.
FLASHFORGE MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS
DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
FCC Notice
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: [1] This device may not cause harmful interference,
and [2] this device must accept any interference received, including
interference that may cause undesired operation.
Flashforge shall not be liable for errors contained herein for incidental
consequential damages in connection with furnishing, performance or use of
this material.
This document contains proprietary information protected by copyright.
Copyright © 2023 Zhejiang Flashforge 3D Technology Co., Ltd. All Rights
Reserved.
Filament Requirements
Filament Storage
It’s recommended to use the filaments offered by Flashforge, or from the brands
accepted by Flashforge. Due to the different properties of filaments, you need to
modify printing parameters when using those which are not offered by Flashforge.
All polymers degrade with time. Do not unpack filament until necessary. Filament
should be stored in a dry and dust-free environment.
Name
Extruder quantity
Printing precision
Positioning precision
Layer thickness
Build volume
Nozzle diameter
Printing speed
Highest extruder
temperature
Supported filament
Power supply
Device size
Connectivity
Filament run-out reminder
Build plate
Remote camera monitoring
HEPA 13 Air filter
Adventurer 4 Pro
1
±0.1 mm
(test of a 100mm cube)
X/Y-axis：0.011 mm；
Z-axis：0.0025 mm
0.1~0.4 mm
220 x 200 x 250 mm
0.4(default)
0.6/0.3 mm(optional)
10~300mm/s
265℃
ABS/PLA/PETG/PLA-CF/PETG-CF
AC100-240V/DC 24V/
13.3A,320W
500(L)*470(W)*550(H)mm
USB / Wi-Fi/ Ethernet
√
PEI flexible steel platform
√
√
Parameters
05
Chapter 1 Adventurer 4 Pro
5. Filament intake cover
7. Platform base
9. Touch screen
4. Spool holder
1. Power switch
2. Power socket
8. Build plate
6. Front cover
20. Camera
13. Filament guide tube joint
15. Fan for cooling the extruder
11. Ethernet input
12. Extruder
10. USB
16. Fan for cooling the model
21. Air filter
17. Buckle 18. Air duct
3. Filament cover
19. Nozzle
14. Cable slot
21
1.1 Component Introduction
06
1
2
3
4
5
9
10
78
6
11
12
20
13
14
15
16
17
18
19
3D Printer Filament After-Sales
Service Card
Screwdriver
0.6-265 Nozzle
User Guide Unclogging
Pin Tool
Power Cable
Grease
Allen Wrench
Glue Stick
Filament Guide
Tube Joint
Leveling Card
USB Flash Drive
1.2 Packing List
07
1. Open the carton. 2. Take out the top foam box, power
cord, after-sales service card, user
guide and USB flash drive.
3. Take out the printer from the carton,
and remove the bubble wrap around
the printer. Tear off the fixing tapes
and the front door protective bag.
4. Open the front door of the printer
and take out the EPE foam filled
inside and filament.
08
Chapter 2 Unpacking
5. Take out the printer from the carton,
and remove the bubble wrap around
the printer. Tear off the fixing tapes
and the front door protective bag.
Table des matières
Autres manuels Flashforge Imprimante 3D
Flashforge
Flashforge THOR500T Manuel utilisateur
Flashforge
Flashforge Finder Manuel utilisateur
Flashforge
Flashforge Adventurer 4 Manuel utilisateur
Flashforge
Flashforge Inventor Manuel utilisateur
Flashforge
Flashforge Creator3 Manuel utilisateur
Flashforge
Flashforge Adventurer3 Manuel utilisateur
Flashforge
Flashforge Finder Manuel utilisateur
Flashforge
Flashforge Creator Pro 2 Manuel utilisateur
Flashforge
Flashforge Creator 3 Manuel utilisateur
Flashforge
Flashforge Finder Manuel utilisateur
Flashforge
Flashforge ADVENTURER 3 Manuel utilisateur
Flashforge
Flashforge DREAMER Manuel utilisateur
Flashforge
Flashforge Guider II Manuel utilisateur
Flashforge
Flashforge ADVENTURER 3 V2 Manuel utilisateur
Flashforge
Flashforge Adventurer 5M Pro Manuel utilisateur
Flashforge
Flashforge Creator 3 Manuel utilisateur
Flashforge
Flashforge Finder 3 Manuel utilisateur
Flashforge
Flashforge DREAMER Manuel utilisateur
Flashforge
Flashforge DREAMER Manuel utilisateur
Flashforge
Flashforge AD1 Manuel utilisateur
