Emerson Rosemount 5408 Manuel utilisateur

Quick Start Guide

00825-0100-4408, Rev AD

March 2018

Rosemount™ 5408 and 5408:SIS Level

Transmitters

Cone Antenna

1 About this guide

This Quick Start Guide provides basic guidelines for the Rosemount 5408 and

5408:SIS Level Transmitters. Refer to the Rosemount 5408 and 5408:SIS

Reference Manual for more instructions. The manual and this guide are also

available electronically on Emerson.com/Rosemount.

WARNING!

Failure to follow safe installation and servicing guidelines could result in

death or serious injury.

•Make sure the transmitter is installed by qualified personnel and in

accordance with applicable code of practice.

•Use the equipment only as specified in this manual. Failure to do so may

impair the protection provided by the equipment.

•For installations in hazardous locations, the transmitter must be installed

according to the Rosemount 5408 and 5408:SIS Product Certifications

document and System Control Drawing (D7000002-885).

Explosions could result in death or serious injury.

•Verify that the operating atmosphere of the transmitter is consistent with

the appropriate hazardous locations certifications.

•Before connecting a Field Communicator in an explosive atmosphere,

ensure the instruments are installed in accordance with intrinsically safe

or non-incendive field wiring practices.

•Do not remove the transmitter cover in explosive atmospheres when the

circuit is live.

•Both transmitter covers must be fully engaged to meet explosion-proof

requirements.

Electrical shock could cause death or serious injury.

•Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

•Make sure the mains power to the transmitter is off and the lines to any

other external power source are disconnected or not powered while

wiring the transmitter.

Process leaks could result in death or serious injury.

•Make sure that the transmitter is handled carefully. If the process seal is

damaged, gas might escape from the tank.

Quick Start Guide March 2018

2Rosemount 5408 and 5408:SIS Level Transmitters

CAUTION!

Hot surfaces

The flange and process seal may be hot at high process temperatures. Allow

to cool before servicing.

March 2018 Quick Start Guide

Quick Start Guide 3

2 Confirm approval type

For hazardous locations transmitters labeled with multiple approval types:

Permanently mark the checkbox of the selected approval type(s).

Label with Multiple Approval TypesFigure 2-1:

Quick Start Guide March 2018

4Rosemount 5408 and 5408:SIS Level Transmitters

3 Mount the transmitter

3.1 Flanged version

1. If applicable, assemble the segmented cone antenna (see Chapter 9).

2. Lower transmitter with antenna and flange into the nozzle.

Gasket

3. Tighten bolts and nuts with sufficient torque for the flange and gasket

choice.

4. Align the transmitter head (see Chapter 4).

3.2 Flanged version with air purge ring (option code PC1)

1. If applicable, assemble the segmented cone antenna (see Chapter 9).

March 2018 Quick Start Guide

Quick Start Guide 5

2. Place a suitable gasket on the tank flange.

3. Place the purge ring over the gasket.

4. Place a suitable gasket over the purge ring.

Note

A minimum gasket thickness of 0.125 in. (3.2 mm) is required for flanges

with protective plate design.

5. Lower transmitter with antenna and flange into the nozzle.

Quick Start Guide March 2018

6Rosemount 5408 and 5408:SIS Level Transmitters

Antenna with air purge holes

6. Tighten bolts and nuts with sufficient torque for the flange and gasket

choice.

1.0 in. (25.5 mm)

7. Connect the air purging system. Use thread sealant or suitable gasket

according to your site procedures.

March 2018 Quick Start Guide

Quick Start Guide 7

0.4 in. (10 mm)

G3/8-in.

Incoming Air Supply SpecificationTable 3-1:

Maximum pressure Recommended pressure

190 psi (13 bar) 100 to 115 psi (7 to 8 bar)

8. Align the transmitter head (see Chapter 4).

3.3 Threaded version, antenna diameter (D) < Thread

diameter (d)

3.3.1 Flanged tank connection

1. If applicable, assemble the segmented cone antenna (see Chapter 9).

2. Place a suitable gasket on the tank flange.

3. Place the customer supplied flange over the gasket.

Quick Start Guide March 2018

8Rosemount 5408 and 5408:SIS Level Transmitters

4. Tighten the bolts and nuts with sufficient torque for the flange and

gasket choice.

5. Apply anti-seize paste or PTFE tape on threads according to your site

procedures.

Gasket may be used as a sealant for adapters with 1½- or 2-in. BSPP

(G) threads.

6. Lower transmitter with antenna and flange into the nozzle.

March 2018 Quick Start Guide

Quick Start Guide 9

Gasket

(for 1½-in. and 2-in.

BSPP (G) threads only)

7. Align the transmitter head (see Chapter 4).

3.3.2 Threaded tank connection

1. If applicable, assemble the segmented cone antenna (see Chapter 9).

2. Apply anti-seize paste or PTFE tape on threads according to your site

procedures.

Gasket may be used as a sealant for adapters with 1½- or 2-in. BSPP

(G) threads.

3. Mount the transmitter on the tank.

Quick Start Guide March 2018

10 Rosemount 5408 and 5408:SIS Level Transmitters

Autres manuels pour Rosemount 5408

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Emerson Émetteur

Emerson

Emerson Rosemount 848T Manuel utilisateur

Emerson

Emerson Rosemount 2051 Wireless Series Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Rosemount 702 Manuel utilisateur

Emerson

Emerson Rosemount 644 Manuel utilisateur

Emerson

Emerson Rosemount Wireless Permasense WT210 Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount 2088 Manuel utilisateur

Emerson

Emerson Rosemount 2088 Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount 2051 Wireless Series Manuel utilisateur

Emerson

Emerson Micro Motion 4200 Manuel utilisateur

Emerson

Emerson Rosemount 1056 Manuel utilisateur

Emerson

Emerson Rosemount 2051 Manuel utilisateur

Emerson

Emerson Rosemount 644h Manuel utilisateur

Emerson

Emerson Micro Motion Transmitters and Discrete Controllers Series... Manuel d'exploitation

Emerson

Emerson Rosemount 644h Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount 702DX22 Manuel utilisateur

Emerson

Emerson Rosemount 644 Manuel utilisateur

Emerson

Emerson Rosemount 644 Manuel utilisateur

Emerson

Emerson Rosemount 326P Manuel utilisateur

Emerson

Emerson Rosemount 5408 Manuel utilisateur

Emerson

Emerson Rosemount 4088B MultiVariable Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur