Emerson Rosemount 3051 Manuel utilisateur

Quick Start Guide

00825-0100-4100, Rev CA

May 2015

Rosemount 3051 Pressure Transmitter and

Rosemount 3051CF DP Flowmeters

with WirelessHART®Protocol

4100_0100_RevCA.fm Page 1 Friday, May 8, 2015 3:03 AM

May 2015

Quick Start Guide

NOTICE

This guide provides basic guidelines for Rosemount 3051 Wireless Transmitters. It does not provide

instructions for configuration, diagnostics, maintenance, service, troubleshooting or Intrinsically Safe (I.S.)

installations. Refer to the Rosemount 3051 Wireless Reference Manual (document number

00809-0100-4100) for more instruction. This manual is also available electronically on

www.rosemount.com.

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate local,

national, and international standards, codes, and practices. Review the approvals section of the 3051

reference manual for any restrictions associated with a safe installation.

Before connecting a HART®-based communicator in an explosive atmosphere, make sure the instruments

in the loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.

Process leaks may cause harm or result in death.

To avoid process leaks, only use the o-ring designed to seal with the corresponding flange adapter.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and the terminals. High voltage that may be present on leads can cause

electrical shock.

NOTICE

Shipping considerations for wireless products.

The unit was shipped to you without the power module installed. Remove the power module prior to

shipping the unit.

Each power module contains one “D” size primary lithium-thionyl chloride battery. Primary lithium batteries

are regulated in transportation by the U.S. Department of Transportation, and are also covered by IATA

(International Air Transport Association), ICAO (International Civil Aviation Organization), and ARD

(European Ground Transportation of Dangerous Goods). It is the responsibility of the shipper to ensure

compliance with these or any other local requirements. Consult current regulations and requirements before

shipping.

Contents

Wireless considerations . . . . . . . . . . . . . . . . 3

Mount the transmitter . . . . . . . . . . . . . . . . . . 4

Connect the power module . . . . . . . . . . . . 8

Trim the transmitter . . . . . . . . . . . . . . . . . . . . 8

Verify transmitter configuration . . . . . . .10

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .13

Product Certifications . . . . . . . . . . . . . . . . .14

4100_0100_RevCA.fm Page 2 Friday, May 8, 2015 3:03 AM

Quick Start Guide

May 2015

Wireless considerations

Power up sequence

The power module should not be installed on any wireless device until the Smart

Wireless Gateway is installed and functioning properly. This transmitter uses the

green power module (order model number 701PGNKF). Wireless devices should

also be powered up in order of proximity from the Smart Wireless Gateway,

beginning with the closest. This will result in a simpler and faster network

installation. Enable Active Advertising on the Gateway to ensure that new devices

join the network faster. For more information, see the Smart Wireless Gateway

Manual (document number 00809-0200-4420).

Connecting the transmitter with a Field Communicator

In order for the Field Communicator to interface with the 3051 Wireless

transmitter, the power module must be connected. This transmitter uses the

Green power module (order model number 701PGNKF). Figure 1 shows how to

connect the Field Communicator to the transmitter. Open the power module

compartment to hook up the leads.

Figure 1. Field Communicator Connections

4100_0100_RevCA.fm Page 3 Friday, May 8, 2015 3:03 AM

May 2015

Quick Start Guide

Step 1: Mount the transmitter

Mounting in liquid flow applications

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Mount the transmitter so that the drain/vent valves are oriented upward.

Figure 2. Liquid Flow Applications

A. Coplanar

B. In-line

Mounting in gas flow applications

1. Place taps in the top or side of the line.

2. Mount beside or above the taps.

Figure 3. Gas Flow Applications

A. Coplanar

B. In-line

Mounting in steam flow applications

1. Place taps to the side of the line.

2. Mount beside or below the taps.

3. Fill impulse lines with water.

Figure 4. Steam Flow Applications

A. Coplanar

B. In-line

Flow

4100_0100_RevCA.fm Page 4 Friday, May 8, 2015 3:03 AM

Quick Start Guide

May 2015

Attaching mounting brackets

Figure 5. Panel and Pipe Mount

Panel mount Pipe mount

Coplanar flange

Traditional flange

In-line

4100_0100_RevCA.fm Page 5 Friday, May 8, 2015 3:03 AM

May 2015

Quick Start Guide

Figure 6. Common Transmitter Assemblies

A. Transmitter with coplanar flange

B. Transmitter with coplanar flange and optional flange adapters

C. Transmitter with traditional flange and optional flange adapters

D. Transmitter with coplanar flange and optional manifold and flange adapters

Bolts are typically carbon steel or stainless steel. Confirm the material by viewing

the markings on the head of the bolt and referencing Table 1 on page 7. If bolt

material is not shown in Table 1, contact a local Emerson Process Management

representative for more information.

Bolt installation

1. Carbon steel bolts do not require lubrication and the stainless steel bolts are

coated with a lubricant to ease installation. However, no additional lubricant

should be applied when installing either type of bolt.

2. Finger-tighten the bolts.

3. Torque the bolts to the initial torque value using a crossing pattern. See

Table 1 for initial torque value.

4. Torque the bolts to the final torque value using the same crossing pattern. See

Table 1 for final torque value.

5. Verify the flange bolts are protruding through the isolator plate before

applying pressure.

Bolting considerations

If the transmitter installation requires assembly of the process flanges, manifolds,

or flange adapters, follow these assembly guidelines to ensure a tight seal for

optimal performance characteristics of the transmitters. Use only bolts supplied

with the transmitter or sold by Emerson Process Management as spare parts.

Figure 6 illustrates common transmitter assemblies with the bolt length required

for proper transmitter assembly.

4 x 1.75-in. (44 mm)

4 x 1.75-in.

(44 mm)

4 x 2.88-in. (73 mm)

4 x 1.75-in. (44 mm)

4 x 1.75-in.

(44 mm)

4 x 2.25-in.

(57 mm)

4100_0100_RevCA.fm Page 6 Friday, May 8, 2015 3:03 AM

Quick Start Guide

May 2015

Table 1. Torque Values for the Coplanar Flange and Flange Adapter Bolts

In-line gage transmitter orientation

The low side pressure port (atmospheric reference) on the in-line gage

transmitter is located in the neck of the transmitter, behind the housing. The vent

path is between the housing and sensor of the transmitter. (See Figure 7.)

Keep the vent path free of any obstruction, including but not limited to paint,

dust, and lubrication by mounting the transmitter so that the process can drain

away.

Figure 7. In-line Gage Low Side Pressure Port

A. Low side pressure port (atmospheric reference)

Consider housing rotation

To improve visibility of optional LCD display:

1. Loosen the housing rotation screw.

2. First rotate the housing clockwise to the desired location. If the desired

location cannot be achieved due to thread limit, rotate the housing counter

clockwise to the desired location (up to 360° from thread limit).

3. Re-tighten the housing rotation screw (see Figure 8).

Bolt material Head markings Initial

torque

Final

torque

Carbon Steel (CS) 300 in.-lbs. 650 in.-lbs.

Stainless Steel (SST) 150 in.-lbs. 300 in.-lbs.

B7M

316

STM

316

B8M

4100_0100_RevCA.fm Page 7 Friday, May 8, 2015 3:03 AM

May 2015

Quick Start Guide

Figure 8. Housing Rotation

A. Housing rotation screw (5/64-inch hex wrench required)

Step 2: Connect the power module

1. Remove the power module cover.

2. Connect the Green power module (see Figure 9).

Figure 9. Power Module

A. Power module

Step 3: Trim the transmitter

Devices are calibrated by the factory. Once installed, it is recommended to

perform a zero trim on gage and differential pressure transmitters to eliminate

error due to mounting position or static pressure effects. A zero trim can be

performed using either a Field Communicator or configuration buttons.

For instructions using AMS®, see the Rosemount 3051 Wireless Product Manual

(00809-0100-4100).

Note

When performing a zero trim, ensure that the equalization valve is open and all wet legs are filled

to the correct level.

4100_0100_RevCA.fm Page 8 Friday, May 8, 2015 3:03 AM

Quick Start Guide

May 2015

Trimming with a Field Communicator

1. Equalize or vent the transmitter and connect Field Communicator.

2. At the menu, input the HART Fast Key sequence.

3. Follow the commands to perform a zero trim.

For connecting with a Field Communicator, refer to Figure 1 on page 3.

Trimming with Digital Zero Trim button

1. Set the transmitter pressure.

2. Remove the electronics housing cover.

3. Press and hold the zero button for two seconds to perform a digital zero trim.

4. Reinstall transmitter housing cover. Ensure a proper seal by installing the

electronics housing cover so that polymer contacts polymer (i.e. no o-ring

visible).

Figure 10. Digital Zero Button

A. Digital zero button

Note

A zero trim can also be completed using AMS Wireless Configurator once the device has joined the

network.

It is not recommended to zero an absolute transmitter, models 3051CA or 3051TA.

From the HOME screen, enter the Fast Key sequence

Device Dashboard Fast Keys 2, 1, 2

Digital Zero

Trim

4100_0100_RevCA.fm Page 9 Friday, May 8, 2015 3:03 AM

May 2015

Quick Start Guide

Step 4: Verify transmitter configuration

Operation can be verified in four locations:

At the device via the Local Display (LCD).

By using the Field Communicator.

Via the Smart Wireless Gateway’s integrated web interface.

Via AMS Wireless Configurator.

Verify transmitter configuration using LCD display

The LCD will display the output values at the same rate as the wireless update

rate. Refer to the Rosemount 3051 Wireless manual for error codes and other

LCD messages. Press and hold the Diagnostic button for at least five seconds to

display the TAG, Device ID, Network ID, Network Join Status, and Device Status

screens.

Verify transmitter configuration using Field Communicator

For HART Wireless transmitter communication, a 3051 Wireless Transmitter

Device Descriptor is required. For connecting with a Field Communicator, refer to

Figure 1 on page 3.

Searching for

Network Joining Network Connected with

Limited Bandwidth Connected

From the HOME screen, enter the Fast Key sequence

Device Dashboard Fast Keys 3, 5

N E T w K

S R C H N G

n e t w k

N E G O T

n e t w k

L I M -O P

n e t w k

O K

4100_0100_RevCA.fm Page 10 Friday, May 8, 2015 3:03 AM

Autres manuels pour Rosemount 3051

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Emerson Émetteur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount MultiVariable 4088A Manuel utilisateur

Emerson

Emerson Rosemount 3051HT Manuel utilisateur

Emerson

Emerson Rosemount 1208 Manuel utilisateur

Emerson

Emerson Rosemount 148 Manuel utilisateur

Emerson

Emerson Rosemount 3100 Series Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Fisher 4200 Manuel utilisateur

Emerson

Emerson Incus GDU-01-TT Manuel utilisateur

Emerson

Emerson Micro Motion IFT9701 Manuel utilisateur

Emerson

Emerson Rosemount 848T Manuel utilisateur

Emerson

Emerson Rosemount 5408 Manuel utilisateur

Emerson

Emerson Rosemount 644 Manuel utilisateur

Emerson

Emerson Rosemount 520 Manuel utilisateur

Emerson

Emerson Rosemount 702 Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Rosemount 702 Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Guide rapide

Emerson

Emerson Rosemount 3051HT Manuel utilisateur

Emerson

Emerson Rosemount 5408 Manuel utilisateur

Emerson

Emerson Rosemount 705 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur