Emerson Rosemount 3051 Manuel utilisateur

Quick Installation Guide

00825-0100-4001, Rev BA

November 2002 Model 3051

www.rosemount.com

¢00825-0100-4001I¤

HART®

Model 3051 Pressure Transmitter

with HART®Protocol

Step 1: Mount the Transmitter

Step 2: Consider Housing Rotation

Step 3: Set the Jumpers

Step 4: Connect the Wiring and Power Up

Step 5: Configure the Transmitter

Step 6: Trim the Transmitter

Product Certifications

Start

End

4001_RevBA.fm Page 1 Monday, November 25, 2002 2:27 PM

Quick Installation Guide

00825-0100-4001, Rev BA

November 2002 Model 3051

Rosemount and the Rosemount logotype are a registered trademarks of Rosemount Inc.

IMPORTANT NOTICE

This installation guide provides basic guidelines for Rosemount® Model 3051

transmitters. It does not provide instructions for configuration, diagnostics,

maintenance, service, troubleshooting, Explosion-Proof, Flame-Proof, or

intrinsically safe (I.S.) installations.

Refer to the Model 3051 reference manual (document number

00809-0100-4001) for more instruction. This manual is also available

electronically on www.rosemount.com.

WARNING

Explosions could result in death or serious injury:

Installation of this transmitter in an explosive environment must be in

accordance with the appropriate local, national, and international standards,

codes, and practices. Please review the approvals section of the

Model 3051 reference manual for any restrictions associated with a safe

installation.

• Before connecting a HART-based communicator in an explosive

atmosphere, make sure the instruments in the loop are installed in

accordance with intrinsically safe or non-incendive field wiring practices.

• In an Explosion-Proof/Flame-Proof installation, do not remove the

transmitter covers when power is applied to the unit.

Process leaks may cause harm or result in death.

• Install and tighten process connectors before applying pressure.

Electrical shock can result in death or serious injury.

• Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

Rosemount Inc.

8200 Market Boulevard

Chanhassen, MN USA 55317

T (US) (800) 999-9307

T (Intnl) (952) 906-8888

Fax (952) 949-7001

Fisher-Rosemount

GmbH & Co.

Shipping Address:

Argelsrieder Feld 3

82234 Wessling

Germany

Tel 49 (8153) 9390

Fax 49

(

8153

)

939172

Emerson Process

Management Asia Pacific

Private Limited

1 Pandan Crescent

Singapore 128461

T (65) 6777 8211

F (65) 6777 0947/65 6777 0743

4001_RevBA.fm Page 2 Monday, November 25, 2002 2:27 PM

Quick Installation Guide

00825-0100-4001, Rev BA

November 2002 Model 3051

STEP 1: MOUNT THE TRANSMITTER

Liquid Flow Applications

1. Place taps to the side of the line.

2. Mount level or below the taps.

3. Mount the drain/vent valve

upward.

Gas Flow Applications

1. Place taps in the top or

side of the line.

2. Mount level or above the taps.

Steam Flow Applications

1. Place taps to the side of the line.

2. Mount level or below the taps.

3. Fill impulse lines with water.

Flow

4001_RevBA.fm Page 3 Monday, November 25, 2002 2:27 PM

Quick Installation Guide

00825-0100-4001, Rev BA

November 2002 Model 3051

Panel Mount(1)

(1) Panel bolts are customer supplied.

Pipe Mount

Coplanar Flange

Traditional Flange

Model 3051T

Model 3051H

4001_RevBA.fm Page 4 Monday, November 25, 2002 2:27 PM

Quick Installation Guide

00825-0100-4001, Rev BA

November 2002 Model 3051

STEP 2: CONSIDER HOUSING ROTATION

STEP 3: SET THE JUMPERS

If alarm and security jumpers are not installed, the transmitter will

operate normally with the default alarm condition alarm high and the

security off.

Housing Rotation

To improve field access or to

better view the optional LCD

meter:

1. Loosen the housing rotation

set screw.

2. Turn the housing left or right up

to 180° from its original

position. Over rotating will

damage the transmitter.

3. Retighten the set screw.

Figure 1. Transmitter Electronics Board

Without LCD Meter With LCD Meter

Housing Rotation Set

Screw (9/64-inch)

Alarm Jumper

Security

Alarm Jumper

Security

4001_RevBA.fm Page 5 Monday, November 25, 2002 2:27 PM

Quick Installation Guide

00825-0100-4001, Rev BA

November 2002 Model 3051

STEP 4: CONNECT THE WIRING AND POWER UP

Use the following steps to wire the transmitter:

1. Remove the housing cover on the side marked FIELD

TERMINALS.

2. Connect the positive lead to the "+" terminal, and the negative lead

to the "–" terminal.

NOTE

Do not connect the powered signal wiring to the test terminals. Power

could damage the test diode in the test connection. Shielded, twisted

pair cable should be used for best results. Use 24 AWG or larger wire

and do not exceed 5,000 feet (1 500 meters).

3. Plug and seal unused conduit connections.

4. If applicable, install wiring with a drip loop. Arrange the drip loop

so the bottom is lower than the conduit connections and the

transmitter housing.

Figure 2 shows wiring connections necessary to power a Model 3051

and enable communications with a hand-held HART communicator.

For low-power transmitters, refer to the reference manual.

Figure 2. Transmitter Wiring Diagrams

Wiring in the Field Transient Wiring

Installation of the transient protection terminal block does not provide

transient protection unless the Model 3051 case is properly grounded.

Current

Meter

RL ≥ 250 Ω

Power

Supply

RL ≥ 250 Ω

Current Meter

24 V dc

Supply

4001_RevBA.fm Page 6 Monday, November 25, 2002 2:27 PM

Quick Installation Guide

00825-0100-4001, Rev BA

November 2002 Model 3051

Power Supply

The dc power supply should provide power with less than two percent

ripple. The total resistance load is the sum of the resistance of the

signal leads and the load resistance of the controller, indicator, and

related pieces. Note that the resistance of intrinsic safety barriers, if

used, must be included.

Figure 3. Load Limitation

Maximum Loop Resistance = 43.5 (Power Supply Voltage – 10.5)

The HART communicator requires a

minimum loop resistance of 250Ω.

Voltage (V dc)

Load (Ohms)

Operating

Region

10.5 20 30 40 50

42.4

1935

1500

1000

500

4001_RevBA.fm Page 7 Monday, November 25, 2002 2:27 PM

Quick Installation Guide

00825-0100-4001, Rev BA

November 2002 Model 3051

STEP 5: CONFIGURE THE TRANSMITTER

NOTE:

A check (⻫) indicates the basic configuration parameters. At minimum,

these parameters should be verified as part of the configuration and

startup procedure.

Table 1. The Model 275 HART Communicator Fast Key Sequence

Function Fast Key Sequence

Alarm and Saturation Levels 1, 4, 2, 7

Analog Output Alarm Type 1, 4, 3, 2, 4

Burst Mode Control 1, 4, 3, 3, 3

Burst Operation 1, 4, 3, 3, 3

Custom Meter Configuration 1, 3, 7, 2

Custom Meter Value 1, 4, 3, 4, 3

⻫Damping 1, 3, 6

Date 1, 3, 4, 1

Descriptor 1, 3, 4, 2

Digital To Analog Trim (4-20 mA Output) 1, 2, 3, 2, 1

Disable Local Span/Zero Adjustment 1, 4, 4, 1, 7

Field Device Information 1, 4, 4, 1

Full Trim 1, 2, 3, 3

Keypad Input – Rerange 1, 2, 3, 1, 1

Local Zero and Span Control 1, 4, 4, 1, 7

Loop Test 1, 2, 2

Lower Sensor Trim 1, 2, 3, 3, 2

Message 1, 3, 4, 3

Meter Options 1, 4, 3, 4

Number of Requested Preambles 1, 4, 3, 3, 2

Poll Address 1, 4, 3, 3, 1

Poll a Multidropped Transmitter Left Arrow, 4, 1, 1

⻫Range Values 1, 3, 3

Rerange 1, 2, 3, 1

4001_RevBA.fm Page 8 Monday, November 25, 2002 2:27 PM

Quick Installation Guide

00825-0100-4001, Rev BA

November 2002 Model 3051

Scaled D/A Trim (4–20 mA Output) 1, 2, 3, 2, 2

Self Test (Transmitter) 1, 2, 1, 1

Sensor Info 1, 4, 4, 2

Sensor Temperature 1, 1, 4

Sensor Trim Points 1, 2, 3, 3, 5

Status 1, 2, 1, 1

⻫Tag 1, 3, 1

⻫Transfer Function (Setting Output Type) 1, 3, 5

Transmitter Security (Write Protect) 1, 3, 4, 4

Trim Analog Output 1, 2, 3, 2

⻫Units (Process Variable) 1, 3, 2

Upper Sensor Trim 1, 2, 3, 3, 3

Zero Trim 1, 2, 3, 3, 1

Table 1. The Model 275 HART Communicator Fast Key Sequence

Function Fast Key Sequence

4001_RevBA.fm Page 9 Monday, November 25, 2002 2:27 PM

Quick Installation Guide

00825-0100-4001, Rev BA

November 2002 Model 3051

STEP 6: TRIM THE TRANSMITTER

NOTE

Transmitters are shipped from Rosemount Inc. fully calibrated per

request or at the factory default of full scale.

Zero Trim

A zero trim is a single-point adjustment used for compensating

mounting position effects. When performing a zero trim, ensure that

the equalizing valve is open and all wet legs are filled to the correct

level.

If zero offset is less than 3% of true zero, follow the “Using the Model

275 HART Communicator” instructions below. If zero offset is greater

than 3% of true zero, follow the “Using the Transmitter Zero

Adjustment Button” instructions below to rerange.

Using the Model 275 HART Communicator

Using the Transmitter Zero Adjustment Button

Fast Keys Steps

1, 2, 3, 3, 1 1. Vent the transmitter and connect HART communicator.

2. At the menu, input the HART Fast Key sequence.

3. Follow the commands to perform a zero trim.

1. Loosen the certifications label screw and

rotate the label to expose the zero

adjustment buttons.

2. Set the 4 mA point by pressing the zero

button for 2 seconds. Verify that the output

is 4 mA. A meter will display ZERO PASS.

Zero Adjustment Button

4001_RevBA.fm Page 10 Monday, November 25, 2002 2:27 PM

Autres manuels pour Rosemount 3051

Table des matières

Autres manuels Emerson Émetteur

Emerson

Emerson Micro Motion 2400S Manuel utilisateur

Emerson

Emerson Rosemount 3144P Manuel utilisateur

Emerson

Emerson Rosemount 3051G Manuel utilisateur

Emerson

Emerson Rosemount 3051HT Manuel utilisateur

Emerson

Emerson Rosemount 4088B MultiVariable Manuel utilisateur

Emerson

Emerson Rosemount 2088 Manuel utilisateur

Emerson

Emerson Rosemount 3051HT Manuel utilisateur

Emerson

Emerson Micro Motion 5700 Manuel utilisateur

Emerson

Emerson MICRO MOTION 2700 Guide rapide

Emerson

Emerson Rosemount 3144P Manuel utilisateur

Emerson

Emerson Rosemount 702 Manuel utilisateur

Emerson

Emerson Rosemount 248 Manuel utilisateur

Emerson

Emerson Rosemount 148 Manuel utilisateur

Emerson

Emerson Rosemount 2051HT Manuel utilisateur

Emerson

Emerson Rosemount 3308 Series Manuel utilisateur

Emerson

Emerson Rosemount 2090P Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount 3144P Manuel utilisateur

Emerson

Emerson Rosemount 5408 Manuel utilisateur

Emerson

Emerson Rosemount 4088B MultiVariable Manuel utilisateur

Emerson

Emerson Rosemount 8712C Guide de configuration

Emerson

Emerson Rosemount Ultrasonic 3107 Manuel utilisateur

Emerson

Emerson Rosemount MultiVariable 3051SMV Manuel utilisateur

Emerson

Emerson Rosemount 2088 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur