Emerson Rosemount 4088B MultiVariable Manuel utilisateur
Quick Start Guide
00825-0200-4088, Rev CB
September 2018
Rosemount™ 4088B MultiVariable™
Transmitter
with Bristol™ Standard Asynchronous/
Synchronous Protocol (BSAP)/MVS
Protocol
Safety messages
NOTICE
This guide provides basic guidelines for the Rosemount 4088 MultiVariable Transmitter. It does not
provide instructions for diagnostics, maintenance, service, or troubleshooting. Reference the 4088
MultiVariable Transmitter Reference Manual for more instruction. All documents are available
electronically at Emerson.com/Rosemount.
Procedures and instructions in this section may require special precautions to ensure the safety of the
personnel performing the operation. Information that raises potential safety issues is indicated with a
warning symbol ( ). Refer to the following safety messages before performing an operation
preceded by this symbol.
WARNING
Explosions could result in death or serious injury.
Installation of this transmitter in an explosive environment must be in accordance with the appropriate
local, national, and international standards, codes, and practices. Review the approvals section of the
4088 MultiVariable Transmitter Reference Manual for any restrictions associated with a safe
installation.
•Before connecting a Field Communicator in an explosive atmosphere, ensure the instruments in
the loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.
•In an Explosion-proof/Flameproof installation, do not remove the transmitter covers when power
is applied to the unit.
Process leaks may cause harm or result in death.
Install and tighten process connectors before applying pressure.
Electrical shock can result in death or serious injury.
Avoid contact with the leads and terminals. High voltage that may be present on leads can cause
electrical shock.
Conduit/cable entries
•Unless marked, the conduit/cable entries in the transmitter housing use a 1/2–14 NPT thread
form. Entries marked “M20” are M20 x 1.5 thread form. On devices with multiple conduit entries,
all entries will have the same thread form. Only use plugs, adapters, glands, or conduit with a
compatible thread form when closing these entries.
•When installing in a hazardous location, use only appropriately listed or Ex certified plugs,
adapters, or glands in cable/conduit entries.
Contents
Steps required for quick installation .............. 5
Mount the transmitter .................................. 6
Consider housing rotation .......................... 13
Set the switches ......................................... 15
Wiring and power up .................................. 16
Verify device configuration ......................... 25
Trim the transmitter ................................... 26
Product Certifications ................................. 27
Quick Start Guide September 2018
2 Rosemount 4088B MultiVariable Transmitter Quick Start Guide
September 2018 Quick Start Guide
Quick Start Guide 3
1 Steps required for quick installation
•Start >
•Mount the transmitter : Mount the Transmitter
•Consider housing rotation : Consider Housing Rotation
•Set the switches : Set the Switches
•Wiring and power up : Wiring and Power Up
•Verify device configuration : Verify Device Configuration
•Trim the transmitter : Trim the Transmitter
•> Finish
September 2018 Quick Start Guide
Quick Start Guide 5
2 Mount the transmitter
2.1 Liquid flow applications
Procedure
1. Place taps to the side of the line.
2. Mount beside or below the taps.
3. Mount the transmitter so that the drain/vent valves are oriented
upward.
A
A. Direction of flow
2.2 Gas flow applications
Procedure
1. Place taps in the top or side of the line.
2. Mount beside or above the taps.
A
A. Direction of flow
Quick Start Guide September 2018
6 Rosemount 4088B MultiVariable Transmitter Quick Start Guide
2.3 Steam flow applications
Procedure
1. Place taps to the side of the line.
2. Mount beside or below the taps.
3. Fill impulse lines with water.
A
A. Direction of flow
2.4 Mounting brackets
Figure 2-1: Mounting Bracket – Coplanar Flange
Panel mount Pipe mount
September 2018 Quick Start Guide
Quick Start Guide 7
Figure 2-2: Mounting Brackets – Traditional Flange
Panel mount Pipe mount
Figure 2-3: Mounting Brackets – In-line
Panel mount Pipe mount
2.5 Bolting considerations
About this task
If the transmitter installation requires assembly of a process flange, manifold,
or flange adapters, follow these assembly guidelines to ensure a tight seal for
optimal performance characteristics of the transmitter. Only use bolts
supplied with the transmitter or sold by Emerson™ as spare parts. Figure 2-4
illustrates common transmitter assemblies with the bolt length required for
proper transmitter assembly.
Quick Start Guide September 2018
8 Rosemount 4088B MultiVariable Transmitter Quick Start Guide
Figure 2-4: Common Transmitter Assemblies
A
4 × 1.75-in.
(44 mm)
D
4 × 1.75-in.
(44 mm)
4 × 2.25-in.
(57 mm)
C
4 ×1.75-in.
(44 mm) 4 ×1.50-in.
(38 mm)
B
4 × 2.88-in.
(73 mm)
A. Transmitter with coplanar flange
B. Transmitter with coplanar flange and optional flange adapters
C. Transmitter with traditional flange and optional flange adapters
D. Transmitter with coplanar flange and optional Rosemount Conventional
Manifold and flange adapters
Note
For all other manifolds, contact Customer Central technical support.
Bolts are typically carbon steel or stainless steel. Confirm the material by
viewing the markings on the head of the bolt and referencing Table 2-1 . If
bolt material is not shown in Table 2-1, contact the local Emerson
representative for more information.
Use the following bolt installation procedure:
Procedure
1. Carbon steel bolts do not require lubrication and the stainless steel
bolts are coated with a lubricant to ease installation. However, no
additional lubricant should be applied when installing either type of
bolt.
2. Finger-tighten the bolts.
3. Torque the bolts to the initial torque value using a crossing pattern.
See Table 2-1 for initial torque value.
4. Torque the bolts to the final torque value using the same crossing
pattern. See Table 2-1 for final torque value.
September 2018 Quick Start Guide
Quick Start Guide 9
5. Verify the flange bolts are protruding through the sensor module
before applying pressure (see Figure 2-5).
Example
Table 2-1: Torque Values for the Flange and Flange Adapter Bolts
Bolt material Head markings Initial torque Final torque
Carbon Steel
(CS)
B7M
300 in-lb 650 in-lb
Stainless Steel
(SST)
316
316
316
SW
316
STM
316
R
B8M
150 in-lb 300 in-lb
Figure 2-5: Proper Bolt Installation
A
B
A. Bolt
B. Sensor module
Quick Start Guide September 2018
10 Rosemount 4088B MultiVariable Transmitter Quick Start Guide
2.6 O-rings with flange adapters
WARNING
Failure to install proper flange adapter O-rings may cause process leaks, which
can result in death or serious injury. Only use the O-ring that is designed for its
specific flange adapter.
A
B
C
D
A. Flange adapter
B. O-ring
C. PTFE-based profile (square)
D. Elastomer profile (round)
Whenever the flange or adapters are removed, visually inspect the O-rings.
Replace them if there are any signs of damage, such as nicks or cuts. If the O-
rings are replaced, re-torque the flange bolts and alignment screws after
installation to compensate for seating of the O-rings.
2.7 Environmental seal for housing
Thread sealing (PTFE) tape or paste on male threads of conduit is required to
provide a water/dust tight conduit seal and meets requirements of NEMA®
Type 4X, IP66, and IP68. Consult factory if other Ingress Protection ratings are
required. For M20 threads, install conduit plugs to full thread engagement or
until mechanical resistance is met.
2.8 In-line gage transmitter orientation
The low side pressure port (atmospheric reference) on the in-line gage
transmitter is located under the sensor module neck label. (See Figure 2-6)
Keep the vent path free of any obstruction, including but not limited to paint,
dust, and lubrication by mounting the transmitter so that any contaminants
can drain away.
September 2018 Quick Start Guide
Quick Start Guide 11
Autres manuels pour Rosemount 4088B MultiVariable
1
Table des matières
Autres manuels Emerson Émetteur
Emerson
Emerson Rosemount 3051 Manuel utilisateur
Emerson
Emerson Rosemount 5300 Series Manuel utilisateur
Emerson
Emerson Micro Motion 3500 Manuel utilisateur
Emerson
Emerson Rosemount 3101 Manuel utilisateur
Emerson
Emerson Rosemount FCL-01 Manuel utilisateur
Emerson
Emerson Rosemount 702 Manuel utilisateur
Emerson
Emerson Rosemount HART Modbus VeriCase 3308 Series Manuel utilisateur
Emerson
Emerson CSI 9420 Manuel utilisateur
Emerson
Emerson Rosemount 8732EM Manuel utilisateur
Emerson
Emerson Rosemount 848T Manuel utilisateur
Emerson
Emerson Rosemount 5408 Manuel utilisateur
Emerson
Emerson Micro Motion 5700 Manuel utilisateur
Emerson
Emerson Rosemount 8750W Manuel utilisateur
Emerson
Emerson Rosemount OCX 8800 Manuel utilisateur
Emerson
Emerson Rosemount 3144P Manuel utilisateur
Emerson
Emerson Rosemount 3144P Manuel utilisateur
Emerson
Emerson Fisher 4200 Series Manuel utilisateur
Emerson
Emerson Rosemount 3051 Manuel utilisateur
Emerson
Emerson Rosemount 5600 Series Manuel utilisateur
Emerson
Emerson Rosemount 248 Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
