DMP Electronics 1134 Guide d'installation

INSTALLATION AND PROGRAMMING GUIDE

1134 Wireless

Wiegand Module

About the 1134 ............................................ 1

Power Supply......................................................... 1

Zone Terminals ...................................................... 1

Annunciators.......................................................... 1

LED Indicators ....................................................... 1

LED Survey ............................................................ 2

Form C Relay......................................................... 2

Programming Connection................................ 2

Dry/Wet Contact ................................................. 2

PCB Features...............................................3

Program the 1134 ........................................4

Part 1: Device Setup............................................ 4

Part 2: Zone Information .................................. 5

Install the 1134 ............................................6

Mount the 1134...................................................... 6

Wire the Electronic Lock.................................. 7

Isolation Relay ...................................................... 9

Install the 333 Suppressor ..............................10

Wire the Zone Terminals...................................11

Connect a Card Reader....................................13

TABLE OF CONTENTS

Program the 1134 Options....................... 15

Program Start Display ......................................15

Serial Number Display......................................15

Initialization Option ...........................................15

Initialize Conﬁrm Option .................................16

Activate Zone 2 Bypass ...................................16

Zone 2 Bypass Time .......................................... 17

Relock on Zone 2 Change...............................17

Activate Zone 3 Request to Exit ..................18

Zone 3 REX Strike Time...................................19

Activate Onboard Speaker .............................19

Custom Card Deﬁnitions ........................ 20

Any Card Format...............................................20

Card Formats ......................................................20

Format Name......................................................20

Wiegand Code Length .....................................21

Site Code Position and Length ....................22

User Code Position and Length................... 22

Require Site Code .............................................22

Site Code Display ..............................................23

Number of User Code Digits.........................23

No Communication with Panel ....................24

Remove Keypad.................................................25

Public Card Formats ............................... 26

Product Speciﬁcations ............................27

Readers and Credentials .........................28

FCC Information ...................................... 30

Industry Canada Information.................. 31

Digital Monitoring Products, Inc. | 1134 Installation and Programming Guide 1

ANNUNCIATORS

An on-board programmable piezo provides local

annunciation at the 1134. You can also connect a

variety of switched ground annunciators to the

1134 for remote annunciation.

LED INDICATORS

The 1134 provides two indicator LEDs. The

SURVEY (Red) LED turns on for the same

duration as the door strike relay. The WIEGAND

(Yellow) LED turns on for one second to indicate

receipt of a valid Wiegand input.

The 1134 Wireless Wiegand Module allows you to use the powerful built-in access control capability of

DMP panels. DMP panels provide access control, arming, and disarming using proximity, mag-stripe,

biometric or other Wiegand-output authentication devices.

The 1134 connects and operates wirelessly with DMP panels. A keypad may be plugged directly into

the 1134 for local programming. The 1134 includes the following features:

POWER SUPPLY

The 1134 operates at 12/24VDC from the power

supply supporting a door’s magnetic lock or

door-strikes. It also provides a 10 Amp Form C

relay contact for lock control.

ZONE TERMINALS

The 1134 has four onboard zones that can be

programmed for a variety of burglary or access

control applications.

ABOUT THE 1134

2 1134 Installation and Programming Guide | Digital Monitoring Products, Inc.

LED SURVEY

The 1134 provides a Survey LED capability to

allow one person to conﬁrm communication with

the wireless receiver while the cover is removed.

Mount the 1134 away from large metal objects

because it may impair performance. Do not

mount the 1134 inside a metal enclosure or install

in a drop ceiling.

1. With the cover removed, hold the 1134 in the

exact desired location.

2. Press the tamper switch to send data to the

panel and determine if communication is

conﬁrmed or faulty.

Conﬁrmed: If communication is

conﬁrmed, for each press or release of the

tamper switch, the LED blinks

immediately on and immediately o.

Faulty: If communication is faulty, the

LED remains on for about 8seconds or

ﬂashes multiple times in quick succession.

Relocate the 1134 or receiver until the LED

conﬁrms clear communication.

FORM C RELAY

The 1134’s Form C relay draws up to 35mA of

current. Refer to the NC/C/NO (Dry Contact

Relay) and the Isolation Relay sections in this

document for more information.

PROGRAMMING CONNECTION

The 1134 provides a keypad programming

connection that allows you to use a standard

DMP LCD keypad for initial setup.

DRY/WET CONTACT

Apply power to the door relay (WET setting) or

leave it unpowered (DRY setting).

Digital Monitoring Products, Inc. | 1134 Installation and Programming Guide 3

1234 5 6 7 810 11 12 13 14

LC ASRED WHT GRN BLK Z1 Z2 Z3 Z4RA GND GND

SURVEY

WIEGAND

PROG

DRY

WET

RESET TAMPER

DISABLE

SURVEY

GND

LED Survey

Button

Piezo

Wiegand

Inputs

Status

Indicator

Outputs

Zones

Reset

Tamper

LED

Indicators

Keypad

Programming

Header

Power

Supply

Door Relay

Terminal

Dry/Wet

Contact

PCB FEATURES

Figure 1: PCB Features

4 1134 Installation and Programming Guide | Digital Monitoring Products, Inc.

PROGRAM THE 1134

Refer to the panel programming guide as needed.

1. Reset the panel.

2. At the keypad, enter 6653 (PROG) to access the PROGRAMMER menu.

PART 1: DEVICE SETUP

1. In DEVICE SETUP, press CMD until you get to DEVICE NO: -.

2. Enter a DEVICE NO:- and press CMD.

3. Enter a DEVICE NAME and press CMD.

4. (XT30/XT50 only) Select YES when WIRELESS? displays.

5. (XR150/XR550 only) Select DOOR for DEVICE TYPE and press CMD.

6. (XR150/XR550 only) Select WLS at COMM TYPE and press CMD.

Note: Panel version 191 or higher software is required.

7. Enter the eight-digit SERIAL#:- and press CMD.

Note: Enter the Type 14 serial number found on the 1134 PCB or by connecting a keypad to the

header on the 1134.

8. Enter the SUPRVSN TIME and press CMD.

Digital Monitoring Products, Inc. | 1134 Installation and Programming Guide 5

PART 2: ZONE INFORMATION

1. In ZONE INFORMATION, enter the wireless ZONE NO: - and press CMD.

2. Enter the ZONE NAME and press CMD.

3. Select the ZONE TYPE and press CMD.

4. At NEXT ZN?, select NO.

5. Select YES when WIRELESS? displays.

6. Enter the eight-digit SERIAL#:- and press CMD.

Note: Enter the Type 08 serial number found on the 1134 PCB or by connecting a keypad to the

header on the 1134.

7. Enter the CONTACT number being used.

8. Enter the SUPRVSN TIME and press CMD.

9. At the NEXT ZN? prompt, select YES and continue to program up to three more zones.

Note: Zones must be entered sequentially. For example, if you program zone 71, you need to

program zone 72 as the next contact. Use the same serial number for each contact.

6 1134 Installation and Programming Guide | Digital Monitoring Products, Inc.

INSTALL THE 1134

The 1134 comes in a high-impact plastic housing that you can mount directly to a wall, backboard,

or other ﬂat surface.

For easy installation, the back and ends of the 1134 housing have wire entrances. The back also

contains multiple mounting holes that allow you to mount the 1134 on a single-gang switch box.

DMP recommends mounting the 1134 near the protected door. Remove the PCB from the housing

base to install the housing to the wall. See Figure2 for mounting hole locations.

1MOUNT THE 1134

Mounting Hole

Figure 2: Mounting Hole Locations

Autres manuels pour 1134

Table des matières

Autres manuels DMP Electronics Unité de contrôle

DMP Electronics

DMP Electronics 714N-POE Guide d'installation

DMP Electronics

DMP Electronics Wiegand 734N Manuel utilisateur

DMP Electronics

DMP Electronics RoBoard RM-G146 Manuel utilisateur

DMP Electronics

DMP Electronics 734N-WIFI Guide de l'administrateur

DMP Electronics

DMP Electronics RoBoard RM-G212 Manuel utilisateur

DMP Electronics

DMP Electronics 780 Guide d'installation

DMP Electronics

DMP Electronics 734 Manuel utilisateur

DMP Electronics

DMP Electronics 734 Guide d'installation

DMP Electronics

DMP Electronics 736P Radionics Manuel utilisateur

DMP Electronics

DMP Electronics 734 Guide d'installation

DMP Electronics

DMP Electronics 1116 Manuel utilisateur

DMP Electronics

DMP Electronics 734 Guide d'installation

DMP Electronics

DMP Electronics XR100 Manuel utilisateur

DMP Electronics

DMP Electronics X1 Guide d'installation

DMP Electronics

DMP Electronics 734INT Guide d'installation

DMP Electronics

DMP Electronics 711S Manuel utilisateur

DMP Electronics

DMP Electronics Wiegand 734N Guide d'installation

DMP Electronics

DMP Electronics 738ZplusINT Manuel utilisateur

DMP Electronics

DMP Electronics 738Zplus Manuel utilisateur

DMP Electronics

DMP Electronics RoBoard RM-G211 Manuel utilisateur

DMP Electronics

DMP Electronics 712-8 Manuel utilisateur

DMP Electronics

DMP Electronics Wiegand 734N Manuel utilisateur

DMP Electronics

DMP Electronics 865 Manuel utilisateur

DMP Electronics

DMP Electronics ITI 738I Guide d'installation

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur