Cisco Meraki Z1 Manuel utilisateur
Z1 Installation Guide
This document describes how to install and set up the Z1 teleworker gateway. Additional reference documents are
available online at: www.meraki.com/library/products.
Z1 Overview
The Meraki Z1 is an enterprise teleworker gateway designed for telecommuting employees and IT staff. It is also a great
all-in-one device to test the capabilities of Meraki's cloud-managed networking. This gateway provides the following
features:
• Support for four LAN connections
• Dual-concurrent 802.11n radios for wireless connections
• Wall screws and anchors for mounting drywall surface, either vertically or horizontally
Package contents
In addition to the Z1, the following are provided.
1
The Z1 front panel
Ports and Status Indicators
The Z1 uses a single LED to inform the user of the device's status.
LED Status Meaning
Flashing white Operation in progress
Solid white Power is applied, Fully operational
The Z1 back panel
Additional functions on the back panel are described below, from left to right.
eset button
Insert a paper clip if a reset is required.
• A brief, momentary press: To delete a downloaded
configuration and reboot.
• Press and hold for more than 10 sec: To force the
unit into a full factory reset.
2
LAN ports
These 4 ports provide connectivity to computers,
printers, access points, or Ethernet switches.
A steady green LED indicates bidirectional connectivity,
and flashing green indicates traffic.
WAN / Internet port Provides connectivity to the WAN.
USB port USB 2.0 for 3G/4G wireless cards
Power input Designed for use only with the unit’s power supply.
The Z1 bottom panel
Please note that the serial number is located on the product label at the bottom panel of Z1
Mounting hardware
The supplied wall screws and anchors allow you to mount the gateway on a drywall surface, either vertically or
horizontally.
• For mounting on drywall, use a ¼-in drill bit, then insert the plastic and screw assemblies.
3
• For mounting on wood or a similar surface, use only the screws.
• Allow the heads of the screws to stick out far enough to be inserted securely into the back of the gateway.
Connecting to WAN
All Meraki Z1 devices must have an IP address. This section describes how to configure your local area network before
you deploy it. A local management web service, running on the gateway, is accessed through a browser running on a
client PC. This web service is used for configuring and monitoring basic ISP/WAN connectivity.
Setting up a static IP address
Do the following to configure basic connectivity and other networking parameters:
1. Using a client machine such as a laptop, connect to one of the four LAN ports of the Z1.
2. Using a browser on the client machine, access the gateway's built-in web service by browsing to
http://setup.meraki.com. (You do not have to be connected to the Internet to reach this address)
3. Click Uplink configuration under the Local status tab. The default credentials use the device serial number as
the username, with a blank password field.
4. Choose Static for the IP Assignment option.
5. Enter the IP address, subnet mask, default gateway IP and DNS server information.
Setting up a DHCP IP address
By default all Z1 devices are configured to DHCP from upstream WAN / ISP servers. Simply plug the Z1's WAN /
Internet port to your upstream circuit and wait a few minutes for the unit to negotiate a DHCP address.
Additional settings
Setting VLANs
If your WAN uplink is on a trunk port, choose VLAN tagging > Use VLAN tagging and enter the appropriate value for
VLAN ID for your network.
To ensure that the client PC is redirected to the local web service in the following step, you must disable all
other network services (ex: wi-fi) on your client machine.
When the WAN connection is fully enabled, the device's front LED will be solid white.
4
Setting PPPoE
PPPoE authentication may be required if you are connecting Z1 device to a DSL circuit. You need to know your
authentication option and credentials (supplied by your ISP) in order to complete these steps.
• Choose Connection Type > PPPoE.
• Select your Authentication option.
• If you select Use authentication, enter appropriate values for Username and Password.
Web proxy settings
These settings take effect if the Z1 device has to fall back to using HTTP to contact the Cloud Controller. By default, web
proxy is disabled. To enable web proxy, do the following:
• Choose Web proxy > Yes.
• Enter values as appropriate for Hostname or IP and Port.
• If you require authentication, choose Authentication > Use authentication, and enter appropriate values for
Username and Password.
Configuring physical link settings
To configure physical link settings on the Ethernet ports, click Local status > Ethernet configuration. You can enable
half duplex, full duplex, and autonegotiation, as well as set 10- or 100-Mbps data rates.
Power efficiency modes
The Meraki Z1 Teleworker Appliance has an off mode and a networked standby or efficient idle mode, both with power
consumption less than 12W.
In off mode, the power consumption is a measured 0.3W. In the networked standby or efficient idle mode, the power
consumption is under that of full operation mode, which is a measured 6.6W. This mode is initiated after treating the last
payload packets.
To activate and/or deactivate wireless network ports, you may use the physical on/off switch or deactivate through the
Meraki Dashboard.
To apply all configuration settings to the gateway, be sure to click Save Settings at the bottom of the page.
5
Table des matières
Autres manuels Cisco Porte
Cisco
Cisco IG21-VZ-K9 Manuel utilisateur
Cisco
Cisco Linksys WAG54G2 Manuel utilisateur
Cisco
Cisco AS5400XM Manuel utilisateur
Cisco
Cisco Linksys WAG310G Manuel utilisateur
Cisco
Cisco ASR 5000 Series Mode d’emploi
Cisco
Cisco SPA232D Mode d’emploi
Cisco
Cisco 3527 PRI G Manuel d'installation et d'exploitation
Cisco
Cisco IC3000 Manuel
Cisco
Cisco Linksys SPA8000-XU Instructions d'utilisation d'origine
Cisco
Cisco TelePresence ISDN GW MSE 8321 Manuel utilisateur
Cisco
Cisco TES301 Manuel utilisateur
Cisco
Cisco DPA 7610 Mode d’emploi
Cisco
Cisco 3545 PRI Manuel d'installation et d'exploitation
Cisco
Cisco Small Business Pro series Mode d’emploi
Cisco
Cisco IG21 Series Mode d’emploi
Cisco
Cisco SPA3000 Manuel utilisateur
Cisco
Cisco ATA 186 Manuel de l'opérateur
Cisco
Cisco AS5400XM Mode d’emploi
Cisco
Cisco IG21 Series Manuel
Cisco
Cisco 3522 BRI Manuel d'installation et d'exploitation
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
