Cisco SPA3000 Manuel utilisateur

Table des matières

Autres manuels Cisco Porte

Cisco

Cisco Firepower 1600 Manuel utilisateur

Cisco

Cisco VG202 Manuel

Cisco

Cisco Firepower 2100 Manuel utilisateur

Cisco

Cisco TelePresence Advanced Media Gateway 3610 Manuel utilisateur

Cisco

Cisco Linksys SPA400 Manuel d'utilisation

Cisco

Cisco Intelligent Wireless Access Gateway Manuel utilisateur

Cisco

Cisco Physical Access Gateway Manuel utilisateur

Cisco

Cisco VG420 Mode d’emploi

Cisco

Cisco DPC Manuel utilisateur

Cisco

Cisco Small Business Pro SA520 Guide de dépannage

Cisco

Cisco VG200 Manuel utilisateur

Cisco

Cisco Small Business Pro series Mode d’emploi

Cisco

Cisco Explorer 9800 Manuel utilisateur

Cisco

Cisco S195 Manuel utilisateur

Cisco

Cisco 450 Manuel

Cisco

Cisco 545 Serial Manuel d'installation et d'exploitation

Cisco

Cisco REN301 Manuel utilisateur

Cisco

Cisco DPC2425 Manuel utilisateur

Cisco

Cisco WAG54G Manuel utilisateur

Cisco

Cisco Meraki Go Mode d'emploi

Cisco

Cisco 3521 Manuel de service

Cisco

Cisco DPC Manuel utilisateur

Cisco

Cisco VG248 - Gateway Manuel

Cisco

Cisco VG350 Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur

Set Up the SPA3000

Document ID: 108740

Contents

Introduction

How do you initially set up an SPA3000?

Related Information

Introduction

This article is one in a series to assist in the setup, troubleshooting, and maintenance of Cisco Small Business

products (formerly Linksys Business Series).

Refer to Cisco Technical Tips Conventions for more information on document conventions.

Q. How do you initially set up an SPA3000?

A. In setting up the SPA3000, make sure you have a one touch tone analog phone, your

NodePhone account details, and access to a standard phone port. You should also have these

package contents:

Phone Adapter Unit♦ Ethernet Cable Standard Phone Cable♦ A 5 Volt Power Adapter♦

Note: This guide has been prepared with firmware 2.0.13, the current supported firmware

release for NodePhone. If you are using an earlier firmware, the web configuration screen

might not look the same as the images in this document. Cisco recommends upgrading your

SPA3000 to version 2.0.13, which is available from the Cisco Download Center ( registered

customers only) .

In order to set up the SPA3000, complete these steps:

Ensure the SPA3000 Power Supply is Connected Properly1. Connect the SPA30002.

Ensuring the SPA3000 Power Supply is Connected Properly

Make sure the power adapter is plugged to an available power outlet.1.

After the plug is connected to the power adapter, connect the SPA3000. For

instructions, complete the next steps.

2.

Connecting the SPA3000

Connect the phone cable to the wall jack with ADSL service, and then connect the

other end to the LINE port of the gateway. Then, connect the Ethernet cable from the

SPA3000 to one of the Ethernet ports (1,2,3 or 4 ) of the Linksys gateway.

1.

Connect the phone cable to the wall jack with ADSL service, then connect the other

end to the line port of the ADSL line filter.

2.

Connect the ADSL modem line to the ADSL port of the ADSL router, and the local

phone line should be connected to the LINE port of the SPA3000.

3.

Connect the phone to the PHONE port on the SPA3000.4.

The PSTN phone line goes from the Local phone port of the Line Filter to the Line

port on the SPA3000. The Phone is connected to the Phone port of the SPA3000. The

Ethernet cable is connected between the ADSL router and the SPA3000.

5.

Related Information

Technical Support & Documentation − Cisco Systems•

Contacts & Feedback | Help | Site Map

© 2013 − 2014 Cisco Systems, Inc. All rights reserved. Terms & Conditions | Privacy Statement | Cookie Policy | Trademarks of

Cisco Systems, Inc.

Updated: Dec 12, 2008 Document ID: 108740