Cisco AS5400XM Mode d’emploi

CHAPTER

3-1

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

Installing the Cisco AS5400XM Universal

Gateway

This chapter guides you through the installation of the Cisco AS5400XM universal gateway and includes

the following sections:

•Setting Up the Chassis, page 3-1

•Connecting to the Network, page 3-5

•Connecting the Console Terminal and Modem, page 3-9

•Connecting to the BITS Port, page 3-10

•Connecting to the Alarm Port, page 3-11

•Supplying Power, page 3-12

•Where to Go Next, page 3-15

Warning

Only trained and qualified personnel should be allowed to install or replace this equipment.

Statement 49

Warning

This equipment is intended to be grounded. Ensure that the host is connected to earth ground during

normal use.

Statement 39

Warning

Incorrect connection of this or connected equipment to a general purpose outlet could result in a

hazardous situation.

Statement 87

Setting Up the Chassis

You can set the chassis on a desktop or install it in a rack. Use the procedure in this section that best

meets the needs of your network:

•Setting the Chassis on a Desktop

•Rack-Mounting the Chassis

3-2

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

Chapter 3 Installing the Cisco AS5400XM Universal Gateway

Setting Up the Chassis

Warning

When installing or replacing the unit, the ground connection must always be made first and

disconnected last.

Statement 1046

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be

accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Setting the Chassis on a Desktop

The location of the chassis is extremely important for proper operation. Equipment placed too close

together, inadequate ventilation, and inaccessible panels can cause malfunctions and shutdowns, and can

make maintenance difficult. The following information will help you to plan the location of the chassis:

•Plan for access to both front and rear panels of the chassis.

•Ensure that the room where the chassis operates has adequate ventilation. Remember that electrical

equipment generates heat. Ambient air temperature may not cool equipment to acceptable operating

temperatures without adequate ventilation.

Attach the rubber feet as shown in Figure 3-1. Rubber feet are included in the accessory kit that shipped

with your Cisco AS5400XM universal gateway.

Figure 3-1 Attaching the Rubber Feet

37208

Universal gateway

chassis bottom

3-3

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

Chapter 3 Installing the Cisco AS5400XM Universal Gateway

Setting Up the Chassis

Rack-Mounting the Chassis

This section describes how to rack-mount the chassis. The Cisco AS5400XM universal gateway arrives

with 19-inch (48.26-cm) rack-mount brackets and larger brackets for use with a 23- (58.42-cm) or

24-inch (60.96-cm) rack. (See Figure 3-2.)

The following information will help you plan your equipment rack configuration:

•Enclosed racks must have adequate ventilation. Ensure that the rack is not congested, because each

unit generates heat. An enclosed rack should have louvered sides and a fan to provide cooling air.

Heat generated by equipment near the bottom of the rack can be drawn upward into the intake ports

of the equipment above.

•When mounting a chassis in an open rack, ensure that the rack frame does not block the intake or

exhaust ports. If the chassis is installed on slides, check the position of the chassis when it is seated

in the rack.

•Baffles can isolate exhaust air from intake air, which also helps to draw cooling air through the

chassis. The best placement of the baffles depends on the airflow patterns in the rack, which can be

found by experimenting with different configurations.

•When equipment installed in a rack (particularly in an enclosed rack) fails, try operating the

equipment by itself, if possible. Power down other equipment in the rack (and in adjacent racks) to

allow the unit under test a maximum of cooling air and clean power.

•Install the chassis and external devices to which it will connect in a contiguous stack.

Warning

Before working on a chassis or working near power supplies, unplug the power cord on AC units;

disconnect the power at the circuit breaker on DC units.

Statement 12

Required Tools and Equipment

You need the following tools and equipment to rack-mount the chassis:

•Number 2 Phillips screwdriver (not included)

•Screws for attaching the chassis to the rack (not included)

•Standard rack-mount brackets (included)

Figure 3-2 Standard Rack-Mount Brackets

H6028

Bracket for 23- or 24-inch rac

Bracket for 19-inch rack

3-4

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

Chapter 3 Installing the Cisco AS5400XM Universal Gateway

Setting Up the Chassis

Installing in a Rack

To install the chassis, follow these steps:

Step 1 Attach the brackets as follows with the standard brackets on the side panels of the Cisco AS5400XM

universal gateway and either the front panel forward or the rear panel forward, as shown in Figure 3-3

and Figure 3-4.

Figure 3-3 Standard Bracket Installation—Front Panel Forward

Figure 3-4 Standard Bracket Installation—Rear Panel Forward

Caution Do not use the handles on the dial feature cards to assist in lifting the chassis.

Step 2 After the brackets are secured to the chassis, and using the screws that you provide, attach the chassis to

the rack as shown in Figure 3-5.

H10643

30860

Note: The second bracket attaches to the other side of the chassis.

3-5

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

Chapter 3 Installing the Cisco AS5400XM Universal Gateway

Connecting to the Network

Figure 3-5 Attaching the Chassis to the 19-Inch Rack—Rear Panel Forward

Connecting to the Network

This section describes how to connect the Cisco AS5400XM universal gateway to your network. The

cables required to connect to a network are not provided. For ordering information, contact customer

service (see the “Obtaining Technical Assistance” section on page xvi) or see Appendix C, “Cabling

Specifications,” for cable and port pinouts.

Warning

To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network

voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some

LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.

Statement 1021

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Caution If the Cisco AS5400XM universal gateway is configured with fewer than seven DFCs, make sure that a

blank slot cover is installed over each open slot to ensure proper airflow.

Note The Cisco AS5400XM universal gateway arrives with all carrier cards and DFCs already installed,

unless you order a card separately as a spare. See the Cisco AS5350XM and Cisco AS5400XM Universal

Gateways Card Installation Guide for card installation instructions.

29034

Note: The second bracket attaches to the rack at the other side

of the chassis. The brackets can also be installed with the

front panel forward.

3-6

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

Chapter 3 Installing the Cisco AS5400XM Universal Gateway

Connecting to the Network

Connecting to an Ethernet Network

You can connect the Cisco AS5400XM universal gateway to an Ethernet network by using a

straight-through RJ-45-to-RJ-45 Ethernet cable to connect the Gigabit Ethernet port to an Ethernet hub.

(See Figure 3-6.)

Caution To comply with the intra-building lightning surge requirements of GR-1089-CORE, Issue III, October

2002, you must use a shielded cable when connecting to either of the Cisco AS5400XM universal

gateway Ethernet ports. The cable must consist of shielded cable terminated by shielded connectors on

both ends, with the cable shield material tied to both connectors.

Figure 3-6 Connecting to an Ethernet Hub (10/100BASE-T Shown)

Connecting to a WAN

Warning

The telecommunications lines must be disconnected 1) before unplugging the main power connector

and/or 2) while the housing is open.

Statement 89

Warning

Hazardous network voltages are present in WAN ports regardless of whether power to the router is

OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching

cables, detach the end away from the router first.

Statement 77

Warning

This equipment is to be installed and maintained by service personnel only as defined by AS/NZS 3260

Clause 1.2.14.3 Service Personnel.

Statement 88

1GE1 10/100/1000BASE-T port

2Ethernet hub

3Straight-through Ethernet cable

871

122115

3-7

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

Chapter 3 Installing the Cisco AS5400XM Universal Gateway

Connecting to the Network

Warning

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

Statement 1023

You can connect the Cisco AS5400XM universal gateway to a WAN in the following ways:

•Use a breakout cable and straight-through RJ-45-to-RJ-45 cable for CT1 connections. (See

Figure 3-7.)

Figure 3-7 Connecting to an RJ-45C (T1) Jack

•Use an E1 cable to connect each E1/PRI port to an E1 channel service unit (CSU) or data service

unit (DSU). (See Figure 3-8.)

Note If you choose a port with 75-ohm input impedance, use an RJ-45-to-75-ohm coaxial cable

adapter and plug it into that port. Use software commands to choose a particular port and the line

termination on that port. For information on software commands, see the Cisco AS5350XM and

Cisco AS5400XM Universal Gateways Software Configuration Guide.

Warning

The E1 interface card may only be installed in an ACA-permitted customer equipment or a Data

Terminal Equipment (DTE) that is exempted from ACA’s permit requirements. The customer equipment

must only be housed in a cabinet that has screw-down lids to stop user access to overvoltages on the

customer equipment. The customer equipment has circuitry that may have telecommunications

network voltages on them.

Statement 90

30848

T1/E1 8 PRI

connector

RJ-45 jack

Straight-through

RJ-45-to-RJ-45 cable

3-8

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

Chapter 3 Installing the Cisco AS5400XM Universal Gateway

Connecting to the Network

Figure 3-8 Connecting to an RJ-45 Jack

•Use a serial transition cable to connect one of the two synchronous serial ports to a modem or a

CSU/DSU. (See Figure 3-9.)

Figure 3-9 Connecting to a CSU/DSU

Note For cable and port pinouts for specific dial feature cards, see Appendix C, “Cabling

Specifications,” in the Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card

Installation Guide.

30847

T1/E1 8 PRI

connector

E1 cable

RJ-45 jack

30846

Serial

transition

cable

CSU/DSU or

other DCE or DTE

Synchronous serial

port (DB-26)

EIA/TIA-232, EIA/TIA-449, EIA/TIA-530A,

EIA/TIA-530, V.35, or X.21 connector

Internet

3-9

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

Chapter 3 Installing the Cisco AS5400XM Universal Gateway

Connecting the Console Terminal and Modem

Use the console terminal for local administrative access to the Cisco AS5400XM universal gateway. You

can only connect a terminal to the console port. You can use the auxiliary port to connect a terminal or

a modem for remote access.

Connecting to the Console Port

To connect a terminal (an ASCII terminal or a PC running terminal emulation software) to the console

port, follow these steps:

Step 1 Connect the terminal using an RJ-45 rollover cable and an RJ-45-to-DB-25 or RJ-45-to-DB-9 adapter.

The adapters provided are labeled TERMINAL. Other types of adapters are not included. (See

Figure 3-10.)

Figure 3-10 Connecting the Console Terminal

Note For additional information on rollover cable pinouts, see Appendix C, “Cabling Specifications.”

30845

Console port

(RJ-45)

RJ-45-to-RJ-45

rollover cable

PC (laptop)

RJ-45

3-10

Cisco AS5400XM Universal Gateway Chassis Installation Guide

OL-6418-02

Chapter 3 Installing the Cisco AS5400XM Universal Gateway

Connecting to the BITS Port

Step 2 Configure your terminal or PC terminal emulation software for 9600 baud, 8 data bits, no parity, and

2 stop bits. To configure the console port, see the Cisco AS5350XM and Cisco AS5400XM Universal

Gateways Software Configuration Guide.

Connecting a Modem to the Auxiliary Port

To connect a modem to the auxiliary port, follow these steps:

Step 1 Connect a modem to the auxiliary port using an RJ-45 rollover cable with an RJ-45-to-DB-25 adapter.

The adapter provided is labeled MODEM. (See Figure 3-11.)

Figure 3-11 Connecting a Modem to the Auxiliary Port

Step 2 Make sure that your modem and the auxiliary port on the Cisco AS5400XM universal gateway are

configured for the same transmission speed (38400 baud is typical) and hardware flow control with Data

Carrier Detect (DCD) and Data Terminal Ready (DTR) operations.

Connecting to the BITS Port

Use a coaxial cable to connect a timing signal generator (TSG) to the BITS port. The BITS port is used

for external clocking. (See Figure 3-12.)

30850

RJ-45-to-RJ-45

rollover cable

Modem

RJ-45-to-DB-25 adapter

(labeled MODEM)

T1/E1 8 PRI

connector

Auxiliary port

(RJ-45)

Autres manuels pour AS5400XM

Table des matières

Autres manuels Cisco Porte

Cisco

Cisco Meraki Z3C Manuel utilisateur

Cisco

Cisco ASR 5000 Mode d’emploi

Cisco

Cisco 3825 - Voice Bundle Router Manuel utilisateur

Cisco

Cisco Linksys WAG54GX2 Manuel utilisateur

Cisco

Cisco Small Business Pro series Mode d’emploi

Cisco

Cisco IC3000 Manuel de l'opérateur

Cisco

Cisco Explorer 9800 Manuel utilisateur

Cisco

Cisco S195 Manuel utilisateur

Cisco

Cisco Meraki Z3 Manuel utilisateur

Cisco

Cisco RF Gateway 1 Modules Manuel utilisateur

Cisco

Cisco DPC Manuel utilisateur

Cisco

Cisco DPC3825 Manuel utilisateur

Cisco

Cisco ASR 5000 Series Mode d’emploi

Cisco

Cisco Meraki Z1 Manuel utilisateur

Cisco

Cisco Network Device MGX 8240 Manuel utilisateur

Cisco

Cisco Linksys WPG12 Manuel utilisateur

Cisco

Cisco Expressway Series Manuel utilisateur

Cisco

Cisco ASR 5000 Mode d’emploi

Cisco

Cisco Catalyst CG113-W6 Manuel

Cisco

Cisco Meraki Go Mode d'emploi

Cisco

Cisco Intelligent Wireless Access Gateway Manuel utilisateur

Cisco

Cisco AS5400 Series Manuel utilisateur

Cisco

Cisco RF Gateway 10 Comment utiliser

Cisco

Cisco VG310 Manuel

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur