Atdec VFS-Q Manuel utilisateur

VFS-Q Page 1 of 4

Installation Guide

VFS-Q

Freestanding Quad Monitor Mount

COMPONENT CHECKLIST

Crossbar

Arms

(x2)

VESA

Plate

(x4)

Quickshift

Donut

(x4)

Upright

Pole

(x1)

Base

(x1)

(Optional)

Security Screw

(x4)

Cable Ball

(x8)

3/5mm

Allen Key

(x1 each)

M8x50mm

Screw (x1)

M6x25mm

Cap Screw

(x2)

Mounting

Screw

M4x16mm

(x16)

Mounting

Screw

M4x12mm

(x16)

Mounting

Screw

M4x10mm

(x16)

Cable Clip

(x4)

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! Each Quickshift Donut supports a maximum weight of 12kg (26.5lbs).

! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.

! The manufacturer accepts no responsibility for incorrect installation.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can

exceed the capacity of the mount even though the monitor weight may be within the stated range. Please contact

Atdec if you would like further information.

REQUIRED TOOLS

• Phillips Head Screwdriver

WEIGHT RANGE

Per Monitor

Flat Monitor

0 - 12kg

0 - 26.5lbs

Curved Monitor

0 - 6kg

0 - 13.5lbs

VFS-Q Page 2 of 4

1. Attach Upright Pole to Base

1.1 Attach the Upright Pole

to the Base as shown below.

Ensure the Cable Slot faces

towards the rear.

OPTIONAL

BOLT THROUGH &

GROMMET MOUNT

Mount can also be bolted

through work surface or

grommet hole with the Atdec

Grommet Clamp (AC-GC),

sold separately.

Cable Slot

USER

BACK

TIGHTEN

FIRMLY

Upright Pole

M8x50mm Screw

5mm Allen Key

3. Attach the VESA Plate to your monitor (Repeat steps 3 to 6 for each monitor)

NOTE: Be sure to select a screw

length that suits the monitor.

3.1 Check VESA mounting compatibility 3.2 Screw VESA Plate to back of

monitor using provided screws.

100mm

75mm

100mm 75mm

Top of

monitor

Too short Too long

2. Attach Crossbar and Doughnuts

2.1 Attach Crossbar to pole. 2.2 Slide doughnuts onto crossbar.

OPEN

SLIDE

DOUGHNUT

ONTO

CROSSBAR

REPLACE

END CAP

CLOSE DOUGHNUT LEVER ONCE

IN PLACE ON CROSSBAR.

HOLD SUPPORT IN PLACE

TIGHTEN

M6x25mm Cap Screw

5mm

Allen Key

CLAMP

Cable slot to

face back

VFS-Q Page 3 of 4

Cable

Balls

Cable

Clips

4. Attach your Display to the Quickshift Donut

4.1 Hook the top of the VESA plate

onto the Quickshift Mount.

4.2 Press and hold the Release

Buttons. Gently push bottom of

VESA Plate into Quickshift Mount.

Release Buttons to lock in place.

4.3 (Optional) Insert the Security

Screw, and tighten using a

Phillips-head Screwdriver.

5. Adjust horizontal position of monitors

HOOK

Back of

Display

OPEN

LOOSEN

TIGHTEN

SLIDE

Release

Button

PUSH

Phillips-head Screwdriver

TIGHTEN

Security Screw

5.1 Open the lever to loosen

the Quickshift Donut.

5.2 Slide the Quickshift

Donut to desired position.

5.3 If necessary, adjust the

tension between the Donut

and the Pole using the 5mm

Allen Key supplied.

5.4 Close the lever to lock the

Quickshift Donut in place.

6. Adjust the ball joint tension 7. Cable Management

6.1 If the monitors are not holding position or are

stiff to move, adjust the tension plate by tightening

or loosening the three screws.

Note: Adjust 3

screws evenly in

small increments

Note: Support the monitor while making adjustments.

3mm

Allen Key

7.1 Connect cables to your Displays, routing them down

the rear of the poles. Push the cables into the slots, using

either the Cable Balls or Cable Cilps to secure them to the

pole as shown.

Cable

Balls

Cable

Clips

Note Ensure enough slack is left in cables

to allow for movement. When the slot in

each pole cannot be used, use the supplied

Cable Clips to secure the display cables.

VFS-Q Page 4 of 4

8.1 Remove monitors

8.3 Remove crossbar from pole

8.5 Lock Doughnut onto pole

OPTIONAL 8. Switch to a triple, dual or single monitor mount

Example

8.2 Slide off doughnut

8.4 Slide Doughnut onto pole

UNLOCK

REMOVE

END CAP

SLIDE DOUGHNUT

OFF CROSSBAR

Slot

UNLOCK

SLIDE DOUGHNUT

ONTO POLE

(Ensure tongue in

doughnut aligns

with slot in pole)

Tongue

REMOVE

POLE CAP 1

PRESS AND

HOLD BUTTONS

LIFT OFF MONITOR

PULL OUT BOTTOM

OF MONITOR

SUPPORT

CROSSBAR

UN-SCREW

CROSSBAR

(Use 5mm

Allen Key)

REMOVE

CROSSBAR

FROM POLE

REPLACE

POLE CAP

LOCK DOUGHNUT

TO POLE

Reattach monitor

following steps 4.1 to 4.3

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Autres manuels Atdec Support et étagère

Atdec

Atdec AWM-A13-B Manuel utilisateur

Atdec

Atdec AV Cart 75 Manuel utilisateur

Atdec

Atdec Visidec Focus Articulated Arm Wall Instructions de fonctionnement

Atdec

Atdec TH-2050-VFM Manuel utilisateur

Atdec

Atdec AWM-W6 Manuel utilisateur

Atdec

Atdec Levitate L-PB Manuel utilisateur

Atdec

Atdec VF-AT-NP Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec AD-TVC-70R Manuel utilisateur

Atdec

Atdec AD-TVC-70A Manuel utilisateur

Atdec

Atdec SYSTEMA SW6S Manuel utilisateur

Atdec

Atdec TH-3060-UF Manuel utilisateur

Atdec

Atdec Freestanding Quad Manuel utilisateur

Atdec

Atdec Levitate Instructions de fonctionnement

Atdec

Atdec AWM-W6 Manuel utilisateur

Atdec

Atdec AWM-WS Manuel utilisateur

Atdec

Atdec AWM Series Manuel utilisateur

Atdec

Atdec AWM-LR Manuel utilisateur

Atdec

Atdec ADBS-3x1-30TW Manuel utilisateur

Atdec

Atdec 8060 Manuel utilisateur

Atdec

Atdec AD-TVAC-CM Manuel utilisateur

Atdec

Atdec AWMS-46W35 Manuel utilisateur

Atdec

Atdec Spacedec Acrobat Swing Arm Double Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur