Atdec AWM-LR Manuel utilisateur

AWM-LR Page 1 of 4

Installation Guide

AWM-LR

Dual Crossbar

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! Do not remove/ throw away the plastic cap on arm links, channel clamp or base.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can

exceed the capacity of the mount even though the monitor weight may be within the stated range.

! The manufacturer accepts no responsibility for incorrect installation.

! This product is compatible with AWM Series monitor arm products.

COMPONENT CHECKLIST

REQUIRED TOOLS

Crossbar

Assembly

(x1)

VESA Plate

(x2)

Handle

(x1)

Screw

M4x10mm

(x8)

Screw

M4x12mm

(x8)

Screw

M4x16mm

(x8)

Plastic

Washer

(x2)

Hole

Cap

(x2)

Screw

M6x16mm

(x2)

Security

screw

(x2)

4mm

Hex Key

(x1)

3mm

Hex Key

(x1)

• Phillips Head Screwdriver

2 - 7kg

(4.5 - 15lbs)

per monitor

WEIGHT RANGE

Monitor weight should be

within the weight range of all

modular elements that make

up the complete monitor

mounting solution.

AWM-LR Page 2 of 4

3. Attach VESA plates to monitors

1. Mount crossbar onto arm

2. (OPTIONAL) Attach handle

1.1. Push crossbar onto shaft at end

of arm. Do not remove plastic cap.

1.3. Tighten joint

screw to secure

rail to arm.

NOTE: Check the crossbar rotation is

smooth after tightening.

1.2. Ensure crossbar is fully pushed

onto shaft.

3.3. Be sure to use a screw length

that suits the monitor.

3.2. Attach VESA head onto monitor

with provided screws.

NOTE: Spacers may be required

for curved, recessed or uneven

monitor surfaces.

100mm

75mm

100mm 75mm

Too short Too long

3.1. Check VESA mounting compatibility.

NOTE: For other sizes, use a suitable

adaptor plate (sold separately).

2.1. Use the 4mm Hex Key to loosely

fasten the handle onto the crossbar.

2.2. Adjust handle to a height that suits

the monitors, then tighten the two screws.

2.3. If not using handle t hole caps.

M6x16

Screw

Plastic

Washer

AWM-LR Page 3 of 4

5. Adjust the ball joint tension

6. Cable Management

4. Mount monitors onto crossbar

5.1. If the monitors are not holding

position or are stiff to move, adjust

the tension plate by tightening or

loosening the three screws.

NOTE: Adjust 3 screws evenly

in small increments

NOTE: Support the monitor

while making adjustments.

3mm

Hex Key

IMPORTANT!

Ensure enough cable slack is given to allow for movement of the monitors.

4.1. Hook the top of the VESA

plate onto the ball joint mount.

4.2. Gently push the bottom of the

monitor until the VESA plate locks

into place.

4.3. (OPTIONAL) Tilt the monitor

upwards to install the security screw.

Tilt Up

Push

Click

Hook

Repeat steps 4.1 to 4.3 for second monitor

AWM-LR Page 4 of 4

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

+/- 5°

Push

Loosen

Tighten

Adjust level of crossbar

8.1. Rotate the

crossbar so that

it sits parallel to

the worksurface.

OPTIONAL: If the crossbar rotation is

too loose or stiff, adjust the tension

screw under the centre of the crossbar.

7.2. Monitors can also be rotated to portrait position.

ANGLEDFLAT

Adjust monitor angle

7.1. Slide the monitors along the crossbar until they

are positioned centrally in the desired position.

Adjust horizontal position of monitors

7. Adjustments

WARNING: If returning display to landscape orientation, ensure the hook is facing upwards.

Autres manuels Atdec Support et étagère

Atdec

Atdec AWM-P G Manuel utilisateur

Atdec

Atdec AD-TVC-45 Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec APA-B Manuel utilisateur

Atdec

Atdec AWMS-BT40 Manuel utilisateur

Atdec

Atdec AWMS-DW6 Manuel utilisateur

Atdec

Atdec AWM-A46-B Manuel utilisateur

Atdec

Atdec AWM-A71 Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-G Manuel utilisateur

Atdec

Atdec AWM-A46 Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec AWM-A13-B Manuel utilisateur

Atdec

Atdec AWM-P G Manuel utilisateur

Atdec

Atdec Visidec VF-AT-NP Manuel utilisateur

Atdec

Atdec AWM-BT Manuel utilisateur

Atdec

Atdec AWMS-2-4640-C Manuel utilisateur

Atdec

Atdec VFS-DV Manuel utilisateur

Atdec

Atdec AD-AC-PH Manuel utilisateur

Atdec

Atdec ADB-FS Manuel utilisateur

Atdec

Atdec TH-2050-VFM Manuel utilisateur

Atdec

Atdec AF-WD Manuel utilisateur

Atdec

Atdec ADBS-4x1-39TW Feuille d'instructions

Atdec

Atdec Spacedec Acrobat Swing Arm Double Manuel utilisateur

Atdec

Atdec VISIDEC FOCUS ARTICULATED ARM DOUBLE Instructions de fonctionnement

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur