Atdec SPACEDEC ACROBAT Instructions de fonctionnement

Please do not

remove card from the

Spacedec Acrobat

Articulated Wall Arm

For your comfort and safety please take a few

moments to adjust the position of your display

To adjust the Spacedec Acrobat Articulated

Wall Arm, please refer to the instructions in

this User Operating Card

Use the Ergonomic Guidelines overleaf

as a guide for correct positioning

Depending on the weight of the display, it may be

necessary to make adjustments to the Ball Joint

Mechanism. If the display doesn’t hold its position

or is too resistant, adjust the four tension screws

located around the Ball Joint (see diagram) using

the supplied 2.5mm Allen Key.

Check the display, and then adjust again if

necessary.

NOTE: Be sure to adjust screws evenly.

Tighten

Loosen

Tension

Screws (x4)

Ball Joint

2.5mm

Allen Key

It is possible to control the amount of resistance

in the Pivot Head to suit your display.

To increase the resistance of the Pivot Head to

suit heavier displays, use the 5mm Allen Key

supplied in the Desk Clamp Box to tighten the

interscrew in a clockwise direction.

To decrease the resistance of the Pivot Head to

suit lighter displays, loosen the interscrew in an

anti-clockwise direction.

NOTE: It is recommended the Pivot

Head be left at the factory setting for

best performance.

Pivot Head

Interscrew

5mm Allen Key

Loosen

Tighten

Lighter

display

Heavier

display

Raise Gas Strut

to suit lighter

display

Arm

5mm

Allen key

Gas Strut

Lighter

Heavier

Lower Gas Strut to

suit heavier display

B.3.1 Depending on the weight of the display,

it may be necessary to adjust the arm. This can

be done by using the supplied 5mm Allen Key.

B.3.2. If the arm tends to automatically rise

or fall when the display is attached, it will be

necessary to make small adjustments to the gas

strut. (see diagram)

B.3.3. If the arm tends to rise, the gas strut

position should be raised. If the arm tends to

fall, the gas strut position should be lowered.

B.1. Adjusting Ball Joint friction

B.2. Adjusting Pivot Head tension

B.3. Adjusting Gas Strut Resistance

USER

OPERATING CARD

SPACEDEC ACROBAT

ARTICULATED WALL ARM

15°

5°

HORIZONTAL SIGHT LINE (d)

CENTRE OF SCREEN

10°-20°

(h)

Adjusting Display

Due to continuing product development, the manufacturer

reserves the right to alter specifications without notice.

Ergonomic Guidelines

Ergonomists recommend that the optimal position of your screen should be slightly below eye level.

When looking at the screen’s centre the user should have a downward visual angle of approx. 10°-20°.

As a guide, the height (h) of your display should be approximately as follows:

Tall Male (Max): 560mm (22”) Tall Female (Max): 520mm (201/2”)

Short Male (Min): 368mm (141/2”) Short Female (Min): 356mm (14”)

For visual comfort, a viewing distance (d) between 500mm (20”) to 750mm (291/2”) is recommended.

Angular adjustments to reduce reflection on your display should range between 5° forward tilt to 15°

backward tilt.

Mechanical Adjustment

If undesired tilt or pan occurs at any stage, this means the factory settings on your Articulated Wall

Arm requires adjustment. Please refer to adjustment details overleaf.

B.1. Ball Joint friction

B.2. Pivot Head tension

B.3. Gas Strut resistance

Your Articulated Wall Arm should already be preset to accommodate the average

size/weight of a display. To adjust the position of your display for visual comfort,

simply hold both sides of the display and adjust to desired position.

Published: 24.10.07©

atdec.com

SPACEDEC ACROBAT

ARTICULATED WALL ARM

B.1.

B.2.

B.3.

Autres manuels Atdec Support et étagère

Atdec

Atdec TELEHOOK 12/30 Multi Manuel utilisateur

Atdec

Atdec VFS-DV Manuel utilisateur

Atdec

Atdec AWM-A71-B Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-FS Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec AF-MC Manuel utilisateur

Atdec

Atdec AWM-A13-B Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-FS Manuel utilisateur

Atdec

Atdec Freestanding Quad Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-G Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-H Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec AWM-BT Manuel utilisateur

Atdec

Atdec Spacedec SD-POS-VBM-B2B Manuel utilisateur

Atdec

Atdec AWM-A46-B Manuel utilisateur

Atdec

Atdec ADB-FS Manuel utilisateur

Atdec

Atdec AWM-W6 Manuel utilisateur

Atdec

Atdec AWM-FC Manuel utilisateur

Atdec

Atdec Focus VF-AT-NP Manuel utilisateur

Atdec

Atdec SYSTEMA SW6S Manuel utilisateur

Atdec

Atdec ADBS-2x1-17TC Manuel utilisateur

Atdec

Atdec Visidec Focus Articulated Arm Wall Instructions de fonctionnement

Atdec

Atdec AWMS-3-137140-C Manuel utilisateur

Atdec

Atdec VF-AT-NP Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur